Question about 1997 Oldsmobile Cutlass Supreme

1 Answer

How to install a cv joint, 1997 olds cutlass

How to install a cv joint, 1997 olds cutlas. I cant find any "snap ring" that i have heard about close to the transmission.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 7,353 Answers

Just pull or pry the axle out of the trans, the clip is on the end of the axle. It just has a groove to retain the axle in so it doesnt just slide out on its own.

Posted on Nov 20, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Do you have to remove the snap ring on 1994 saturn sl 2 to get axel out


The left axle is a little tricky I use a crow bar and tuck the curved end in behind the cup of the axle then look for a good sturdy position on the transmission and do a quick snap on the crowbar and the axle pops out. Be ready with an oil pan if you did not drain the transmission oil as it will come out. Also Saturn transmissions get serviced with dexron III even the manual transmissions. When reinstalling the new axle place the transmission end in first and get the snap ring to hold before re-assembling the rest of it. Is best to insert the end of the axle into the transmission, then hold the axle straight while pushing inward on the axle until you feel the cv joint bottom out inside the cup then with a dead blow hammer, strike the outer end of the cv joint and you should be able to feel the inner snap into place. To make sure that it is reach in and grab the inner axle you should not be able to pull it back out by hand. If you try to hammer on the inner cv joint during installation you take the chance of damaging the boot. And causing premature failure of the inner axle cv joint. Hope this helps.

May 27, 2016 | Saturn SL2 Cars & Trucks

1 Answer

How to remove the cv joint boot on hyundai accent


If you clean away the grease inside the boot and look where the axle goes into the joint there is a snap ring there. Spread the snap ring and pull the joint off the axle.

Oct 02, 2012 | Cars & Trucks

1 Answer

How do you change a cv joint on a 04 kia optima


The CV joints snap ring usually pop when you strike the joint squarely with a hammer. take care not to pop the shaft . If you clean the back of the CV joint you will see if it is a snap ring or a horseshoe type clip (that has to be compressed) either way you strike the CV joint from behind.

Aug 26, 2012 | 2004 Kia Optima

2 Answers

How to change cv joints


I would replace the complete axle assembly,
it would be cheaper and come with a warranty.

Instructions
  1. Remove the CV Joint
    • Remove the boot straps from the CV joint using a standard screwdriver or a pair of diagonal cutting pliers.
    • Slide the boot back over the interconnecting shaft.
    • Get Chevrolet Info at InsideLine Free News, Videos, Photos & More!
      Detach the stop ring at the base of the CV joint assembly using a pair of snap ring pliers.

    • Pull the CV joint assembly from the interconnecting shaft to force the snap ring at the top of the shaft through the CV joint assembly.
    • Tilt the inner cage (the cage holding the balls in place inside the housing) in different angles to remove the six balls. Use your thumb or a hammer and a wooden dowel, if necessary.
    • Tilt the inner cage enough to remove it from its housing.
    • Rotate the race inside the cage--the part that holds the balls against the inner cage--and remove the race from the cage.
      Replace the CV Joint
      • Apply a thick coat of grease to the new CV joint race using special high temperature/high pressure grease (see Tips below).
      • Install the race inside the new cage. Then install the cage/race assembly inside the CV joint housing.
      • Tilt the cage at different angles and fit the new balls in place.
      • Slide a new CV joint rubber boot over the interconnecting shaft.
      • Install a new snap and stop ring on the interconnecting shaft.
      • Push the interconnecting shaft through the CV joint assembly to force the snap ring through the assembly.
      • Apply a thick coat of CV joint grease to all moving parts of the assembly.
      • Apply a coat of CV joint grease to the inside of the rubber boot. Then slide the boot over the CV joint assembly.
      • Install the boot straps at each end of the boot, and tighten the straps using a clamp tool or screwdriver, depending on the type of clamp.


Mar 22, 2012 | 1997 Chevrolet Cavalier

1 Answer

I've got a 1999 2500 Chevy Silverado , that I need to change a cv boot on , can u assist me.?


CV-Joints
Overhaul
These vehicles use several different types of joints. Engine size, transaxle
type, whether the joint is an inboard or outboard joint, even which side of the
vehicle is being serviced could make a difference in joint type. Be sure to
properly identify the joint before attempting joint or boot replacement. Look
for identification numbers at the large end of the boots and/or on the end of
the metal retainer bands.

The 3 types of joints used are the Birfield Joint, (B.J.), the Tripod Joint
(T.J.) and the Double Offset Joint (D.O.J.).

NOTE: Do not disassemble a Birfield joint. Service with a new joint or
clean and repack using a new boot kit.

The distance between the large and small boot bands is important and should
be checked prior to and after boot service. This is so the boot will not be
installed either too loose or too tight, which could cause early wear and
cracking, allowing the grease to get out and water and dirt in, leading to early
joint failure.

NOTE: The driveshaft joints use special grease; do not add any grease
other than that supplied with the kit.

Double Offset Joint
To Remove:

NOTE: The Double Offset Joint (D.O.J.) is bigger than other joints
and, in these applications, is normally used as an inboard joint.


  1. Remove the halfshaft from the vehicle.
  2. Side cutter pliers can be used to cut the metal retaining bands. Remove the
    boot from the joint outer race.
  3. Locate and remove the large circlip at the base of the joint. Remove the
    outer race (the body of the joint).
  4. Remove the small snap ring and take off the inner race, cage and balls as an
    assembly. Clean the inner race, cage and balls without disassembling.
  5. If the boot is to be reused, wipe the grease from the splines and wrap the
    splines in vinyl tape before sliding the boot from the shaft.
  6. Remove the inner (D.O.J.) boot from the shaft. If the outer (B.J.) boot is
    to be replaced, remove the boot retainer rings and slide the boot down and off
    of the shaft at this time.

To Install:

NOTE: Be sure to tape the shaft splines before installing the boots.
Fill the inside of the boot with the specified grease. Often the grease supplied
in the replacement parts kit is meant to be divided in half, with half being
used to lubricate the joint and half being used inside the boot.


  1. Install the cage onto the halfshaft so the small diameter side of the cage
    is installed first. With a brass drift pin, tap lightly and evenly around the
    inner race to install the race until it comes into contact with the rib of the
    shaft. Apply the specified grease to the inner race and cage and fit them
    together. Insert the balls into the cage.
  2. Install the outer race (the body of the joint) after filling with the
    specified grease. The outer race should be filled with this grease.
  3. Tighten the boot bands securely. Make sure the distance between the boot
    bands is correct.
  4. Install the halfshaft to the vehicle.

Except Double Offset Joint
To Remove:


  1. Disconnect the negative battery cable. Remove the halfshaft.
  2. Use side cutter pliers to remove the metal retaining bands from the boot(s)
    that will be removed. Slide the boot from the T.J. case.
  3. Remove the snap ring and the tripod joint spider assembly from the
    halfshaft. Do not disassemble the spider and use care in handling.
  4. If the boot is be reused, wrap vinyl tape around the spline part of the
    shaft so the boot(s) will not be damaged when removed. Remove the dynamic
    damper, if used, and the boots from the shaft.

To Install:


  1. Double check that the correct replacement parts are being installed. Wrap
    vinyl tape around the splines to protect the boot and install the boots and
    damper, if used, in the correct order.
  2. Install the joint spider assembly to the shaft and install the snap ring.
  3. Fill the inside of the boot with the specified grease. Often the grease
    supplied in the replacement parts kit is meant to be divided in half, with half
    being used to lubricate the joint and half being used inside the boot. Keep
    grease off the rubber part of the dynamic damper (if used).
  4. Secure the boot bands with the halfshaft in a horizontal position. Make sure
    distance between boot bands is correct.
  5. Install the halfshaft to the vehicle and reconnect the negative battery
    cable.






Check the CV-boot for wear
tccs7030.jpg








Removing the outer band from the CV-boot
tccs7031.jpg








Removing the inner band from the CV-boot
tccs7032.jpg








Removing the CV-boot from the joint housing
tccs7033.jpg








Clean the CV-joint housing prior to removing boot
tccs7034.jpg








Removing the CV-joint housing assembly
tccs7035.jpg








Removing the CV-joint
tccs7036.jpg








Inspecting the CV-joint housing
tccs7037.jpg








Removing the CV-joint outer snap ring
tccs7038.jpg








Checking the CV-joint snap ring for wear
tccs7039.jpg








CV-joint snap ring (typical)
tccs7040.jpg








Removing the CV-joint assembly
tccs7041.jpg








Removing the CV-joint inner snap ring
tccs7042.jpg








Installing the CV-joint assembly (typical)
tccs7043.jpg




prev.gif next.gif

Oct 07, 2010 | 2002 Chevrolet Silverado 2500HD

1 Answer

Need to know how to remove cv joint for clutch replacement in 2004 toyota corolla s


Take out the drive-axle. Cut the old rubber-boot clamps off and discard them.
Remove the boot from the inner CV joint nnd slide the tripod from the joint housing.
Remove the snap-ring with a pair of snap-ring pliers.
Drive the tripod the tripod joint from the drive-axle with a brass punch and hammer; careful not to damage the bearing surfaces or splines on the shaft.


Oct 31, 2009 | 2004 Toyota Corolla

1 Answer

How does the outer cv joint come apart on a 1992 lexus es300


you have to take the boot off. clean off all the grease. there is a snap ring holding the cv joint to the axle. release the snap ring and joint will slide off.

Oct 03, 2009 | 1992 Lexus Es 300

1 Answer

Cv boot clamp came off somehow from the outer hub assembly


athere is a snap ring within the CV joint the nedds to be spread OPEN to release CV joint from axle, Once CV is cleaned and repacked with grease rintall onto axle by again spreading apart clamp. Prior to installing CV joint slide NEW CV joint boot onto axle, Cleanly intall add'l grrease and reinstall CV boot.

Apr 04, 2009 | 1996 Buick Century

1 Answer

Inner cv joint disassembly


If you are changing the CV joint with shaft, after getting the outer end of the shaft out of the hub, Take a small pry-bar and pry the shaft out of the tranny.

Mar 14, 2009 | 1997 Chevrolet Cavalier

1 Answer

Cv joint replacement


Remove the tire and tighten 2 lugnuts onto the brake rotor. remove the axle nut in center of the brake rotor and drive the axle out of the spindle. If the ball joint is original, you have to grind out the rivets on the lower control arm. Remove and replace the ball joint with the hardware included with the ball joint. Next, pry-unsnap the axle end from the transaxle with a prybay and drive-snap in the new axle shaft into the transaxle. reverse to assemle, align front end and wholla! your done. 1 hour,15 min. $115.00 to do it yourself.

Mar 07, 2009 | 1995 Oldsmobile Cutlass Supreme

Not finding what you are looking for?
1997 Oldsmobile Cutlass Supreme Logo

Related Topics:

193 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7754 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...