Question about 2000 Volvo V70

1 Answer

2000+ v70 whats involved to change drivers side head light ,i cant see were it fixes to exept two bolt at the top ,do i need to remove bumper?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 560 Answers

Yes, screws underneath too.

Posted on Nov 20, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to remove 1996 accord fender


Remove bumper only the side u need,bolts or plastics clips on top, two or three under the radiator support for bumper, remove head light, under the fender by the end of the bumper is a bolt for the bumper and other for the fender, 4 bolts on top, one bolt inside bi the door hinge, one or two in the bottom under the side plastic skirt .

Jun 04, 2014 | 1996 Honda Accord

1 Answer

Chevrolet tracker front bumper removal


the front grille is held on by two bolts on top and the rest are pull tabs holding it on. I would use a flat head screw driver and pop the center one out first then the two on each side under the head lights

Feb 16, 2013 | 2002 Chevrolet Tracker

1 Answer

2003 escalade how to remove front bumper.


I just took this one on today. You'll need a flat head screw driver (a clip puller if you have one) a 15mm socket with a 10" extension and 10mm socket. Pop the hood, remove the plastic guard over the radiator and grill. Remove the 10mm bolt in the center of the grill. Remove the grill by popping the clips off each side then the grill will remove by pulling up. Remove the headlights by removing the two pins, one on top one on the inside of the lamp assembly. Remove 4, 15mm bolts from the top side of the bumper (2 upper, 2 lower that require the extension). From underneath the vehicle remove 2 more 15mm bolts (one from each side). The bolts are located just outside of the fog light assembly and sit horizontally. The bumper is now ready to be uncliped. From the inside of the wheel well use a Flathead screw driver to push in the clip while pulling the bumper away from the mounts. I used a large floor mat to keep the bumper from hitting the ground directly. It's helpful to have a second person to help on the last step.
Good Luck!

Aug 16, 2010 | 2004 Cadillac Escalade

1 Answer

Change head lite bulbs 2000 toyota GTA


The easiest way to change them is to remove the 3 bolts that hold the headlight in place, 1 is directly on top of the headlight, 1 can be seen thru the upper radiator support(of course be sure to remove the plastic engine compartment covers if they are installed), and the 3rd is hidden underneath the front bumper cover, to remove the front bumper cover, move aside the inner wheel well panel nearest the sidemarker lights, pull the bumper cover off slighty fron a plastic snap lock that lines up the bumper with the fender, you should see the bolt as soon as you pull the bumper cover. Each bolt is a 10mm patern so I recommend a small ratchet with extension, once you remove the bolts, the headlights come right off. You might have a rubber cover over where the headlight bulbs are located, simlpy unscrew it, or pull it off whatever your vehicle has, I believe the bulb type is H7, its a standard low-beam bulb, keep in mind the passengerside headlamp is attached to the windshield washer refill reservoir which snaps in and out of place. Install is reverse procedure, I hope this helps, and if you need, go to Newcelica.org for ANYTHING Celica related.

Aug 11, 2010 | 2000 Toyota Celica

2 Answers

Need to change the passenger side headlight


This video will show you how to change the headlight in your Accord.">

May 19, 2010 | 1996 Honda Accord

1 Answer

How do you remove headlight unit on volvo v70 2002


Hedadlight removel Volvo V70 2002

Yes the full front bumper has to be removed. Not as bad as it sounds just take your time. One fixing screw in each wheel arch, two bolts behind black bumper trim each side of no. plate, and five or six plastic
plugs on slam panel. Remember to unplug fog lights if fitted. The lamp unit can then be removed secured by thee bolts two on slam panel and one on the inner side of the lamp near the radiator and a clip on the outer side, obvious when you take a good look and dont try to rush.
I hope this will help anyone else.

Nov 01, 2009 | 2002 Volvo V70

1 Answer

Need to remove bumper of 2000 Honda Accord Coupe


i think there just bulbs unless u have damage and your replacing .i have a 98 also owned 92,94 i just started removing bolts attached to bumper but putting on a little tougher start one top center bolt then do the one on each sidein wheel wells to fit it in there ask someone to help hold while your bolting then do rest of bolts wamo bamo....

Mar 14, 2009 | 1998 Honda Accord

1 Answer

Replace headlight caseing


well you need to take off the front bumper to do this there are retainers up top and their are retainer on bottom of bumper or 10mm bolts and also at the fender edge to bumper bolts same 10mm slide the bumper off then you can put the light in

Jan 26, 2009 | 1991 Honda Civic

2 Answers

How to change the whole headlight assembly on a 05 Honda CRV


You have to remove the front bumper and grill etc

There are 5 bolts holding the headlight assembly in place. 2 at the top and 3 underneath.

Remove the plastic cross piece by prising out the clips and then the grille clips too then unbolt the bolts eithr side under the wheel arch. The bumper is still fastened using cips. Pull the bumper forward to unclip.

Dec 23, 2008 | 2005 Honda CR-V

3 Answers

Side light bulb change on hyundai terracan


hi there
the solution is simple,
you only need to undo the screw on top of the side light/indicator. then facing the head light place a flat headed screw driver under the bottom lip of side light. the bottom of the lihgt is on a small push fit stud, use a sponge or cloth to protect your bumper paint work then just apply pressure gently to lever side light out towards you, It will come dont worry, you may then change your bulbs if you wish remove the whole light unit you will see the bottom bolt as soon as you release the side light. to replace just push back into place then replace screw. whole job takes about five minutes

hope this helps kevan hildred

Nov 23, 2008 | 2003 Hyundai Tucson

Not finding what you are looking for?
2000 Volvo V70 Logo

Related Topics:

50 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volvo Experts

yadayada
yadayada

Level 3 Expert

75842 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8215 Answers

Are you a Volvo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...