Question about 1996 Audi A4

Open Question

Audi 80 Drivers side door wont open...cant open it from the inside or out how do i get it open and remove the inner door panel to access the Door latch..Thanks

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 4 Answers

SOURCE: I need to remove the drivers internal door panel

Remove plastic studs from door closer. Unscrew three retaining screws. remove grab.
Unhook window winder retaining clip. Best done with small long-nose pliers. window winder retaining clip located inside plastic winder handle section. Will need to prise away winder handle from door slightly to expose clip. locate and gently pull clip from winder shaft.
unscrew door opener / lock assembly retaining screw.
gently prise lower trim retaining press studs from door. remove lower trim.
gently , from rear of door, pull upper trim from door and similtaniously prise upper trim press studs from door.
gently giggle door opener / lock assembly through upper trim . remove trim
gently with flat blade, peel off plastic dust sheeting.
access to inside off door is now possible.
Reassembly reverse of above

Cheers !

ozzy11

Posted on Feb 22, 2009

  • 295 Answers

SOURCE: how remove the rear inside door panel on a 2001 oldmobile aurora

The inner door panel is held in by clips and screw.
Look at the door near the door handle there should be screws holding it in and along the outer edge of the door. Once loose, and the door handle removed or the arm rest removed. The door panel then prys out , because of the clips that hold it on. Then pops out by applying pressure to the panel upward to the top of the door. The clips always break because of the design and plastic.

Good luck

Posted on Mar 21, 2009

  • 236 Answers

SOURCE: Audi A6 door handle cable broken - how do you

there are little plastic attachments at the end of the cables. pull those down to unlock the cable

Posted on Jun 17, 2009

  • 1986 Answers

SOURCE: 1999 Volkswagen Passat inside inner door panel

You'll need to remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. If needed, you can pull back the weather seal (can't reuse it, but it's not that important) and you will be able to access everything inside the door

Posted on Aug 14, 2009

  • 1986 Answers

SOURCE: 94 LeSabre inner door panel removal

On the inside trim, you can remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Then you'll need to manipulate the panel and disconnect the door handle linkage from the door handle and disconnect the wiring for your controls

Posted on Sep 23, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

The right passenger door does not open from inside and out side


Find someone with a suitable door release jemmy or entry tool that can release the door lock down the window edge. When open, remove the door trim, access the lock and work out what's wrong. There are rods from the door button and inner handle that may have come adrift.

Jun 02, 2015 | 2004 Audi A6

1 Answer

2003 Ford Galaxy wont open the door from the inside


Remove the inner door panel check the liver latch broken, replace that it will be ok

Jan 14, 2013 | Cars & Trucks

1 Answer

I just obtained a 1989 Cadillac Deville...The drivers door wont open....Locks go up and down...trying to open it form the outside...there is no tension in the handle or from the handle inside either......I...


if you remove the cover that is behind the inside door handle and look you may see the arm that connects to the handle.if its connected then you will have to remove the inner door panel,if its come off the handle and you get a hold of it you can pull on it and the door should open.you have to be patient to remove the door panel with the door closed.you will need to remove some screws to loosen the panel from the steel door inner panel.(arm rest,cover behind the handle).pop up the power door/window switch control and remove the plug attached.pull out the inner door panel to unhook the clips around the outside edge of the panel,you will have to move the seat to get better access to some,then remove the panel and reach into the inner door and move the unlock arm to open the door.you move have clips that are broken that allowed the arms to come off that need replacing to fix the problem.

Jul 16, 2011 | 1989 Cadillac Sedan DeVille

2 Answers

My driver side door will not open. All the other doors open.


you should write a more detailed description but it could possibly be the pin in the hunge that keeps the door propped open, that could be jammer or if the handle/latch is the part that isnt opening then get in through the passenger side and pop off the door panel to the drivers side door and make sure the lines are connected from the door handle to the latch, and if you were in an accident recently depending on the severity it could be a bent frame/door depending where hit

Sep 10, 2010 | 2000 Chevrolet Malibu

1 Answer

Audi a3 r reg remove inner door panel drivers side


On the inside trim, you can remove screws (these screws may be covered by filler pieces or may be visible, or they may require you pry a plastic piece off that covers the screws) that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Then you'll need to manipulate the panel and disconnect the door handle linkage from the door handle and disconnect the wiring for your controls.

Oct 30, 2009 | 2005 Audi A3

1 Answer

The front passenger door will open from the inside but not from the outside.


Requires removing inside panel to gain access to latching mechanism. Most likely a part has broken. Make sure window is raised. Examine all four sides of inner door panel. Look for screws and or screw caps. Remove all screws including door handle, power window and remote mirror controls. Gently pry bottom edge of panel away from door while feeling for resistance (be certain all screws are removed). When inner panel is released, raise panel up and remove. Inspect outer door and inner door latch to determine malfunction (working both controls one at a time). Replace defective parts from dealer or junk yard. Reinstall is reverse.

Jul 09, 2009 | 1992 Buick Park Avenue

3 Answers

How do i replace the window motor


This is a common problem with driver side window. Its just a wear and tear problem. Don't go to the dealership, the Regulator will cost you over $230. Go to Amazon.com and search for the part number which should cost you only $70-80 or so. If you go to a glass place they will charge you dealership price plus $150 per hour. I say do it yourself which goes a little something like this.

TRIM PANEL
REMOVAL

(1) Remove the plug and remove screw attaching
door pull cup to inner door panel.
(2) Remove switch bezel and disconnect power window/
memory switch.
(3) Remove screws attaching trim panel to door
from below map pocket.
(4) If equipped, remove window crank. (Refer to 23
- BODY/DOOR - FRONT/WINDOW CRANK -
REMOVAL)
(5) Remove screw holding door trim to door panel
from behind inside latch release handle.
(6) Disengage clips attaching door trim to door
frame around perimeter of panel.
(7) Lift trim panel upward to disengage flange
from inner belt molding at top of door.
(8) Tilt top of trim panel away from door to gain
access to latch linkage.
(9) Disengage clip attaching linkage rod to inside
latch release handle (Fig. 13).
(10) Separate linkage rod from latch handle.
(11) Disconnect the power door switch, courtesy
lamp electrical connectors.
INSTALLATION
(1) Hold top of trim panel away from door to gain
access to latch linkage.
(2) Place linkage rod in position on latch handle.
(3) Engage clip to hold linkage rod to inside latch
release handle.
(4) Place front door trim panel in position on door.
(5) Install trim panel into inner belt molding at
top of door.
(6) Install clips to attach door trim to door frame
around perimeter of panel.
(7) If equipped, install screw to attach door trim to
door panel behind inside latch release handle.
(8) If equipped, connect power switch into wire
connector.
(9) Place power accessary switch in position on
door trim.
(10) Connect wire connector into memory seat/mirror
switch and install switch into trim panel.
(11) Install screws to attach accessary switch
panel to door trim.
(12) Install screw cover into switch panel.
(13) If equipped, install window crank.
(14) If equipped, install screws to attach trim
panel to door inside map pocket.
(15) If equipped, install screw to attach door pull
cup to inner door panel.
(16) If equipped, install screws to attach door
assist handle to inner door panel.
(17) Connect wire connector into courtesy lamp.
(18) Install lamp in door trim.
(19) Install switch bezel.

WINDOW REGULATOR
REMOVAL

(1) Remove the watershield. (Refer to 23 - BODY/
DOOR - FRONT/WATERSHIELD - REMOVAL)
(2) Remove door glass retaining clips and secure
the window in the up position using masking tape or
equivalent (Fig. 15).
(3) Disconnect wire connector from power window
motor, if equipped.
(4) Loosen screws attaching front and rear window
guide rails to inner door panel (Fig. 16).
(5) Remove screw heads on guide rails from key
hole slots in inner door panel.
(6) Loosen screws attaching regulator to inner door
panel.
(7) Remove regulator from inner door panel.
(8) Extract rear guide rail through inner door
panel rear access hole (Fig. 17).
(9) Extract front guide rail through front access
hole.
INSTALLATION
(1) Insert front guide rail through front access
hole.
(2) Insert rear guide rail through rear access hole.
(3) Place window regulator in position on inner
door panel.
4) Place screw heads on guide rails in position
through key hole slots in inner door panel.
(5) Tighten screws to attach front and rear guide
rails to inner door panel.
(6) Connect wire connector into power window
motor, if equipped.
(7) Install door glass.
(8) Verify door glass alignment and operation.
(9) Install sound shield and door trim panel. __________________
Avatar: EconoVoyager Concept
2001 Dodge Grand Caravan Sport 3.3L
2004 Chrysler Pacifica AWD 3.5L post_thanks.gif quote.gif

Apr 05, 2009 | 1998 Dodge Grand Caravan

3 Answers

1999 Volkswagen Passat inside inner door panel


You'll need to remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. If needed, you can pull back the weather seal (can't reuse it, but it's not that important) and you will be able to access everything inside the door

Mar 25, 2009 | 1999 Volkswagen Passat

Not finding what you are looking for?
1996 Audi A4 Logo

Related Topics:

214 people viewed this question

Ask a Question

Usually answered in minutes!

Top Audi Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

yadayada
yadayada

Level 3 Expert

74896 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14184 Answers

Are you an Audi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...