Question about 2000 Land Rover Range Rover

4 Answers

Range rover p38 radiator removal info - 2000 Land Rover Range Rover

Posted by on

Ad

4 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 275 Answers

First, remove the grille, then the top panel. Remove the viscous coupling and fan. Remove the top radiator mounts, Remove the coolant hoses and oil pipes, remove 4 bolts holding the A/C and intercooler/or PAS radiators (depending if yours is diesel or petrol.) then lift up and out the radiator. Fitting is reversal of removal.
Hope this helps

Posted on Nov 20, 2009

Ad
  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 25 Answers

Almost none of the above is necessary. If it's a petrol engine, remove the top fan cowl (clipped). Remove the fan and viscous coupling - undo the nut in the same direction that the fan rotates. Unclip and remove the remaining fan shroud. Disconnect the top and bottom radiator hoses. Undo one bolt either side near the bottom of the radiator. Lift the radiator out. I can pull mine out in about 5 minutes - I've done it a number of times..

Posted on Dec 11, 2009

  • weric Dec 23, 2010

    is it the same as the p38 diesel with aircom or do you have to pull it all out

×

Ad
  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

How to remove a radiator from freelander 1.9 diesel 2003

Posted on Mar 09, 2010

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

How do i remove the turbo intercooler from diesel p38 rangerover,

Posted on Mar 20, 2011

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1757 Answers

SOURCE: how do i change drive belt on p38 range rover

My sincere apologies for the delayed response.
I am personally going back to answer your unanswered questions.
I have only been a free contributor to this site for the past 4-months.

Not sure if this what you need for the "P38" but it is for the 1996 Range Rover.

I do not know if you still need this information, but I am going ahead and answering it anyway.


Click on the following Link. It has the several Serpentine Belt Diagrams, one of which matches your specific vehicle with your particular options (AC, Power Steering etc..).

Regarding HOW:
Standard Rule to Removal the Serpentine Belt:
1. Find the Tensioner(s). (See Diagrams on Link)
2. Rotate/Move the Tensioner away from contact with the belt and towards the area where the belt is not in contact with the Tensioner Pulley. The Tensioner is spring loaded, and is hard to rotate/move.
3. Remove the loosened belt off one of the other more easily accessed Pulleys
.
Standard Rules for Installing the Serpentine Belt:
a. Pick a Pulley that is most easily accessed. This will usually be on top. This will be the last Pulley that the belt will go on.

b. Using the Diagram: Install the new Serpentine Belt on the remainder of the Pulleys....over, under, left right.
c. Using a Serpentine Belt Tensioner Tool or Wrench or Ratchet Tool: Rotate/Move the Tensioner Pulley/Arm "away" from Belt contact area on the Tensioner. This spring is pretty hard and with a new belt, it will be even harder to install. Rotate/Move this to as-close to the maximum allowed inorder to have enough slack in the belt to get it up and over the last pulley.
d. Using your other hand - Pull the Belt up and over the Last remaining Pulley.
e. Before releasing the pressure on the Tensioner, visually inspect the remainder Pulleys and the Belts' Positioning on them.
Let me know if this helped...

http://www.2carpros.com/car_repair_information/year/1996/make/land_rover/model/range_rover/1996_land_rover_range_rover_drive_belt_routing_diagram.htm

Posted on Mar 13, 2010

alicantecoli
  • 22156 Answers

SOURCE: can i remove radiator from p38 range rover 2.5

play it by ear but i would imagine so providing that the AC pipes are not running in front of the access to take the radiator out

Posted on Dec 23, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why is heater blower on high speed range rover p38 ?


Sounds like a faulty switch pack or the resistor pack. Strongly suggest you do not try to fix it yourself, but you insist on doing so, you will get more info on www. rangerovers.net

May 25, 2014 | 2000 Land Rover Range Rover

1 Answer

Can i remove radiator from p38 range rover 2.5 diesel without aircon being moved


play it by ear but i would imagine so providing that the AC pipes are not running in front of the access to take the radiator out

Dec 23, 2010 | 2000 Land Rover Range Rover

1 Answer

Where is the crank position sensor in a 1996 Rang Rover P38 4.6? How do you replace the crank position sensor in a 1996 Rang Rover P38 4.6? Thanks In Advance For You Help. Greg


sensor should be next to harmonic balancer.usually bolted to motor.balancer has fins behind it which run through crank sensor magnets to send signals to onboard computer.ensure to replace as per removal method

Feb 28, 2010 | 1996 Land Rover Range Rover

1 Answer

How do i resolve Range Rover p38 immobilisor


sounds like keyfob has lost its sync with the car, look online lots of places tell you how to re-ai.lgn them

Jan 08, 2010 | 1999 Land Rover Range Rover

Not finding what you are looking for?
2000 Land Rover Range Rover Logo

2,230 people viewed this question

Ask a Question

Usually answered in minutes!

Top Land Rover Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

yadayada
yadayada

Level 3 Expert

76164 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Land Rover Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...