Question about 1990 Nissan Pulsar

Open Question

How easy is it to replace a clutch cable on my 1999 Nissan Pulsar Plus???

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 104 Answers

SOURCE: need to change the clutch

No, piece 'o cake! Like some other Nissans, but smaller.

Posted on Feb 03, 2009

Ad
BCAS1298
  • 3092 Answers

SOURCE: clutch pedal goes to floor and stays 1999 Nissan

ON A 2000 MAX 6 CYLINDER HAS CLUTCH MASTER CYLINDER AND SLAVE CYLINDER, CHECK FLUID LEVEL AND BLEED CLUTCH SYSTEM AT SLAVE CYLINDER BLEEDER. HAVE NOT HEAR OF CABLE CLUTCH SYSTEM. ONLY HYDO.& LINKAGE. GOOD LUCK

Posted on Nov 05, 2009

  • 171 Answers

SOURCE: 1988 Nissan Pulsar will not engage clutch. Engine

You need to replace the clutch and pressure plate --your clutch is worn out. Plus other parts like throw-out bearing ,pilot bearing and may even need the flywheel machined flat.
You need to take it to a shop or if you are mechanicaly minded could do it your yourself,

Posted on Nov 15, 2009

alicantecoli
  • 22246 Answers

SOURCE: instructions on replacement of a Nissan Pulsar N13 transmission?

manual or auto

Posted on Dec 19, 2009

  • 593 Answers

SOURCE: Clutch cable just fixed and just started to stick to floor again

Check each end of the cable, there should be a clamp that holds the cable casing in place. If the
clamp became loose, when you step on the peddle
it would pull the cable and case not the clutch fork.
And the result would be, what you have now.
I hope this was of some help.

Posted on Jan 28, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Can you adjust the clutch on a 1999 Nissan pulsar ?


if its a hydraulic clutch no, so if you have a problem with engaging the trans you will need a clutch. first check clutch fluid level and for leaks in system.. if its cable you can adjust.

Jun 30, 2015 | Nissan Cars & Trucks

1 Answer

How much does it cost to replace a clutch on 1987 nissan pulsar


clutches cost $700.0 plus original, around $500 after market ( (original equipment in a different box) and the labour costs depend on if the flywheel needs surfacing Time will be around 6 hours at local labour time rate.
Are you sure it is the clutch as problematic master cylinders will make a clutch slip
Get a second opinion from an accredited clutch specialist before you spend money.

Feb 26, 2015 | Nissan Cars & Trucks

1 Answer

1988 nissan pulsar n13 keeps getting stuck in first gear


YOUR CLUTCH CABLE MAY NEED ADJUSTING,HERE'S A LINK ON IT,

Feb 12, 2014 | 1988 Nissan Pulsar

1 Answer

Just replaced my clutch cable in my nissan pulsar n14 1994 mdl and are having difficulty getting the clutch to engage and can't get into gear I can easily once cars of ?


the clutch adjustment will be at the end of the cable . to make the clutch release better the outer cable has to be shortened so see how this can be done . Either by a screw adjustment on the end of the cable or adjusting slots and brackets.. If you do not have a manual as to how to do it then talk with a service department or brake shop and have it explained to you

Dec 25, 2013 | Cars & Trucks

1 Answer

My sons Nissan pulsar n14 clutch is slipping, how hard is this to adjust?


hi, that is an auto adjusting clutch. If it is slipping then either the adjusting mechanism is broken or your clutch is worn out and needs replaced.

Sep 19, 2010 | 1990 Nissan Pulsar

1 Answer

Clutch cable just fixed and just started to stick to floor again


Check each end of the cable, there should be a clamp that holds the cable casing in place. If the
clamp became loose, when you step on the peddle
it would pull the cable and case not the clutch fork.
And the result would be, what you have now.
I hope this was of some help.

Jan 28, 2010 | 1990 Nissan Pulsar

1 Answer

1996 nissan maxima..clutch is slipping is there an adjustment


That is an auto adjusting clutch. If it is slipping then either the adjusting mechanism is broken or your clutch is worn out and needs replaced.

Dec 04, 2009 | 1990 Nissan Pulsar

1 Answer

1988 Nissan Pulsar will not engage clutch. Engine


You need to replace the clutch and pressure plate --your clutch is worn out. Plus other parts like throw-out bearing ,pilot bearing and may even need the flywheel machined flat.
You need to take it to a shop or if you are mechanicaly minded could do it your yourself,

Nov 15, 2009 | 1988 Nissan Pulsar

Not finding what you are looking for?

Open Questions:

See all 1990 Nissan Pulsar Questions

1990 Nissan Pulsar Logo

Related Topics:

322 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...