Question about 2007 BMW 525xi Sedan

1 Answer

I've just bought a new Uni take and talk Nokia

My car has a Bury UNI system 8 fitted and I've I've just bought a new Uni take and talk cradle for my Nokia 6300 and problem is I can hear dial and ringing tones and the other person very clearly but it seems if my microphone doesn't work as they can not hear me. Also the phone button on my steering wheel doesn't seem to activate the phone in either answer or dial mode or interrupt radio.

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.


    An expert that has over 500 points.

  • Expert
  • 436 Answers

There are two cradles available for the 6300, one has two connectors should work when you put the phone in the cradle and switch on the key, the other has one connector and is bluetooth, this requires pairing, you will need to search for bluetooth devices and pair using code 1234. The use of steering wheel controls is not possible with bury car kit. hope this helps. dan

Posted on Mar 03, 2010


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

What's the best way to get too the top starter bolt on a 2001 X j 8 jaguar

use a 13mm socket and a uni joint with extension bar plus ratchet its not that bad to get to

Jul 07, 2017 | Jaguar Cars & Trucks

1 Answer

Do i need to completely remove uni joints to change tailshaft centre bearing on 2003 BA falcon XL sedan

As the "U" joints are bigger than the shaft in the bearing , you will have to pull that joint apart

Mar 14, 2015 | Cars & Trucks

1 Answer

My 2001 silverado 4wd 5.3, hums noticeably in the cab when accelerating around 30mph + I do have a leak rear t-seal and both front t axles and have filled the front thinking that was the problem however...

when you say humming as if out of balance you may have ansqwered your own question. Tail shaft vibration comes in aroun 30 mph and the points I would look for are loose uni joints or a lost balance weight from the tail shaft. To check uni joints look for rust streaks from cross.The next step is to grab firmly either side of the joint and see if there is any movement while twisting you hands in opposite directions. next lift one half of the cross and check for movement in the bearings repeat this at all uni joints check the tail shaft slip joint by trying to twist each half and check for up and down movement at this spline. front shafts fail more readily than rear ones

Jan 06, 2013 | Chevrolet Silverado 1500 Cars & Trucks

2 Answers

What is a sub frame on a auto

The Subframe is a metal frame like enclosure that surrounds the Engine /Transmission. The Engine/ Trans drops into the Subframe and in turn is bolted to it via Engine Mounts and the Subframe is in turn bolted to the uni-body of your car via Subframe Mounts.

Feb 05, 2011 | 1997 Pontiac Sunfire

1 Answer

Car has been lying idle for almost two years while I was at Uni.

gas has a short shelf life so it in a way goes bad you can try some gas conditioner/stablizer and maybe some water remover. try also changing the fuel filter. As a last resort drain the tank but be very carful.

Jul 18, 2010 | 2000 Volkswagen Golf

1 Answer

Can i fit a freelander engine and axles to my series 3

in a word no the freelander is a uni body construction,and most freelander owners would prefer to go for the defender set up not the other way round, you would be better of looking at coil sprung hi breed kits for your s3 and maybe a mitsubshi diesel for economy.

Dec 12, 2009 | 2002 Land Rover Freelander

2 Answers

Shakes at high speeds. 4 New tires, all road force balanced. Wheels aligned.

check your tail sharft uni joints if it is them you will feel it more when you jump off the gas

Nov 21, 2009 | 1995 Buick Park Avenue

1 Answer

Oil leak at rear of gearbox it is a new exchange just fitted I also replaced the slip yoke and uni joint and fitted the genuine seal. toyota hilux with w58 5 speed

well, after all that, it should not leak a drop. if the yoke is new, then either the seal is bad/damaged or the bushing has too much play, allowing the yoke to "wobble" and the seal is unable to contain the oil. another thing to verify is that the vent is open and not plugged.

Oct 01, 2009 | 1997 Toyota Tacoma

1 Answer

How to replace center bearing and the rubber housing that holds it in place

mark the uni joints so you can fit the tail shaft back in the same point, remove the shat and put it on the bench mark both ends of the shaft and undo the bolts fit new joint and re bolt it up making shore to align the marks refit the shaft making shore to align all your markings and tighten up all bolts properly take the truck for a drive and get it up to speed and check for vibrations if all is aligned properly there should be no vibs...

good luck let me no if you need more info and ill try to help

Sep 28, 2009 | 1990 Nissan Hardbody King Cab

Not finding what you are looking for?
2007 BMW 525xi Sedan Logo

648 people viewed this question

Ask a Question

Usually answered in minutes!

Top BMW Experts

Frankie B

Level 2 Expert

65 Answers

Fred Sops

Level 2 Expert

272 Answers


Level 2 Expert

254 Answers

Are you a BMW Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides