Question about 1999 Volkswagen Passat

1 Answer

1645 throttle munfunction - 1999 Volkswagen Passat

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 364 Answers

I assume this is a question?
Shoot down to the mechanics who should have a code reader, he will be able to read and reset any error codes for you. Most mechanics won't charge for looking. Good luck

Posted on Nov 20, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the Engine Throttle Position Sensor located in my 2007 Cadillac DTS


It is located in the throttle body assembly . Your vehicle has electronic throttle control .
Throttle Body Assembly
The throttle body assembly contains the following components:
?€¢
The throttle blade


?€¢
The throttle actuator motor


?€¢
The throttle position (TP) sensor 1 and 2

The throttle body functions are similar to a conventional throttle body with the following exceptions:
?€¢
An electric motor opens and closes the throttle valve.


?€¢
The throttle blade is spring loaded in both directions and the default position is slightly open.


?€¢
There are 2 individual TP sensors within the throttle body assembly.


Oh yea it has two TPS - throttle position sensors ! An you have to replace the whole assembly !

Oct 19, 2015 | Cadillac Cars & Trucks

1 Answer

L300 Saturn 2003 trying to replace my throtter sensor. Can't figure out where to start from. Have no idea where's it located.


Your vehicle has electronic throttle control an the Throttle position sensor's are internal to the throttle body assembly ! Your vehicle has two throttle position sensors .
Throttle Body Assembly
The throttle assembly contains the following components:
?€¢ The throttle blade ?€¢ The throttle actuator motor ?€¢ The throttle position (TP) sensor 1 and 2 You have to replace the Throttle Body Assembly !
Disconnect the negative battery cable. Remove the inlet hose assembly from the throttle body. Disconnect the throttle body electrical connection. Disconnect the hose clamps from the plenum-to-runner connector using theJ 43914 .
Remove the intake plenum bolts. Remove the EGR passage bolt. Rotate the plenum up and remove the throttle body coolant hoses, EVAP hose, and vacuum line from the throttle body.
Remove the throttle body nuts. Remove the throttle body.

Aug 05, 2015 | Saturn Cars & Trucks

2 Answers

How do I solve for My Hyundai sonata model 2009 code P2110 , P2118 in scaning. I changed throttle body and TP sensor. after change of these even I am getting problem in accelerator not increases above


P2110...Faulty Throttle Actuator Control Module
- Throttle Actuator Control Module harness is open or shorted
- Throttle Actuator Control Module circuit poor electrical connection

P2118 - Electronic Throttle Control(ETC) system is made of the components throttle body, Throttle Position Sensor(TPS)1&2 and Accelerator Position Sensor(APS) 1&2. The throttle body contains the actuator, the throttle plate and the throttle position sensor (potentiometer), which are integrated in one housing. The actuator consists of a DC motor with a two-stage gear. The opening angle of the throttle valve is detected by the throttle position sensor which is mounted on the throttle body. And it provides feedback to the ECM to control the throttle motor in order to control the throttle valve opening angle properly in response to the driving condition.

Jan 06, 2015 | 2009 Hyundai Sonata

2 Answers

While starting vehicle ETC warning display vehicle not throttle


This is a warning that something needs to be checked. This happens a lot when a vehicle is jumped with a dead battery. You may have to take to dealer and have ETC reprogramed.
Throttle Control Warning Light More and more vehicles are doing away with the mechanical throttle cable between the driver's foot and the engine throttle body, replacing it with a "drive-by-wire" system. In this system, a throttle pedal sensor sends data to an electronic throttle control computer, which evaluates and relays the throttle request to a specialized electronic throttle motor on the engine throttle body.
The throttle motor opens or closes the actual throttle blade, which increases or decreases the power output of the engine. The throttle control warning light illuminates when a problem is detected in the electronic throttle system.

Jan 04, 2015 | Cars & Trucks

1 Answer

Throttle body sensor location 2005 uplander


the sensor is part of the throttle body and not replaceable here is the throttle body replacement instructions as you will have to replace the entire throttle body it is a very common issue with these
THROTTLE BODY ASSEMBLY REPLACEMENT

REMOVAL PROCEDURE
  1. Remove the air cleaner intake duct.
120434113
  1. Disconnect the electronic throttle control (ETC) electrical connector (1) from the throttle body (2).
113356645
  1. Remove the heater pipe nut at the throttle body.
  2. Remove only the heater inlet pipe.
113356646
  1. Remove the nuts and the bolts from the throttle body.
  2. Remove the throttle body assembly.
  3. Remove the throttle body gasket.
  4. Clean and inspect the throttle body gasket mating surfaces.
NOTE: Do not use solvent of any type when cleaning the gasket surfaces on the intake manifold and the throttle body assembly, as damage to the gasket surfaces and throttle body assembly may result.

Use care in cleaning the gasket surfaces on the intake manifold and the throttle body assembly, as sharp tools may damage the gasket surfaces.

INSTALLATION PROCEDURE
113356646
  1. Install a new gasket, if necessary.
  2. Install the throttle body assembly.
  3. Install the throttle body nuts and the bolts.
NOTE: Refer to Fastener Notice in Service Precautions.

Tighten the nuts and the bolts to 10 N.m (89 lb in) .
113356645
  1. Install the heater inlet pipe.
  2. Install the heater pipe nut to the throttle body.
Tighten the nut to 25 N.m (18 lb ft) .
120434113
  1. Connect the ETC electrical connector (1) to the throttle body (2).
  2. Install the air cleaner intake duct.

Feb 03, 2014 | 2005 Chevrolet Uplander

2 Answers

My 2006 Hyundai sonata reading on a code reader P2118, P2119, P2110


P2118 - Electronic Throttle Control(ETC) system is made of the components throttle body, Throttle Position Sensor(TPS)1&2 and Accelerator Position Sensor(APS) 1&2. The throttle body contains the actuator, the throttle plate and the throttle position sensor (potentiometer), which are integrated in one housing. The actuator consists of a DC motor with a two-stage gear. The opening angle of the throttle valve is detected by the throttle position sensor which is mounted on the throttle body. And it provides feedback to the ECM to control the throttle motor in order to control the throttle valve opening angle properly in response to the driving condition.

P2119 - associated

P2110 - A bulletin provides the procedure to clean the Electronic Throttle Control (ETC)
throttle body of Theta-2.0L/2.4L engine equipped vehicles. If a vehicle exhibits the
condition(s) listed below and deposits are found at the valve-to-bore interface inside the
ETC throttle body, clean the throttle body using the procedure described in this bulletin.

This throttle body cleaning procedure should be performed when diagnosing
the conditions listed below. Do not replace the throttle body prior to performing
this procedure.

Any of the following conditions may be caused by throttle body deposits:
• No start (due to throttle valve stuck closed or air flow signifcantly restricted)
• Rough idle or fluctuating engine speed at idle (due to air flow restriction)
• MIL "On" with DTC P2118 or P2119 occurring along with P2110:
• P2118: Throttle Actuator Control Motor Current Range/Performance
• P2119: Throttle Actuator Control Throttle Body Range/Performance
• P2110: Throttle Actuator Control System-Forced Limited Power

It seems CLEAR you have a STICKING butterfly plate in the throttle body.

Mar 24, 2011 | 2006 Hyundai Sonata

1 Answer

2005 Ford Expedition (4wd) with trouble codes p2104 and p2112 completely cuts off at low speeds. All signs point to throttle position sensor, but want to make sure I'm on the right track.


Shown here is the P2104 obd2 code and their general meaning. For a brief description of any particular OBD2 code and how to fix the obd2 trouble code, please browsw below. P2104 Engine TP Actuator Cntl System
This obd2 code is very common on newer vehicles which contain new design of throttle positioner sensor. Instead of putting a tps sensor at the side of your throttle body as in older engines, a throttle actuator control system is installed which eliminates the mechanical linkage (cable) between the throttle body and the throttle pedal. Under the throttle pedal, a throttle switch is installed and a throttle module or actuator is incorporated beside the throttle body. Because there is no mechanical device that wears out, it is more effecient in delivering better mileage and performance torque (besides...the actuator module performs better in getting all throttle signals to the ecm and trany).
To test this code, check the integrity of the wires going to both the throttle body actuator and the ecm including the throttle switch. Most of the time, if you have symptoms like trany going to a limp mode, the culprit originates from the trany circuit. However, if the symptom is engine related like hesitation, the problem resides in the throttle actuator itself which may sometimes includes the replacement of the whole throttle body assembly. Contact ATS if you need a wiring diagram or detailed fixes for your throttle actuator control system.
TIP:
Before replacing the throttle control actuator and throttle body, try cleaning the throttle plates and all plug-in wiring connections. Also, watch out the throttle body mounting bolts which can easily break (use care) when removing them.

P2112 Throttle Actuator Control System - Stuck Closed

Jan 12, 2010 | 2005 Ford Expedition

3 Answers

What dose the code p1000 mean and p1645


P1645 EVAP Solenoid Output Circuit
P1000 Scan not complete. meaning it didnt finish scanning

Sep 14, 2009 | 2002 Jaguar X-Type

2 Answers

Location of throttle position sensor


the throttle position sensor is located on the side of the throttle body even with the throttle plate.

Jul 08, 2009 | 2003 Jeep Grand Cherokee

Not finding what you are looking for?
1999 Volkswagen Passat Logo

Related Topics:

84 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volkswagen Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

yadayada
yadayada

Level 3 Expert

74945 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7697 Answers

Are you a Volkswagen Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...