Question about 2005 Ford Five Hundred

Open Question

How to access the high level brake light on a ba 2 falcon to replace bulb

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

moparownr
  • 667 Answers

SOURCE: Ford Expedition brake light replacement

once those two screws are removed grab both sides of the light and pull out, the lights are held in with to pop locking pins and those two bolts

Posted on Mar 26, 2009

  • 1 Answer

SOURCE: ba falcon - wish to remove steering wheel

ave aproblem wit my air bag the light turn on and off quen you help me please

Posted on Mar 28, 2009

bluexr6
  • 2 Answers

SOURCE: ba falcon heater

You see ford charge 8 hours labour for replacing the shaft!
A job that at most should take 3 hours. I would hunt around and get some quotes from a Radiator Repair shop or Air con specialist rather then Ford dealerships.

Posted on May 18, 2009

  • 191 Answers

SOURCE: Have BA Ford Falcon with tail lights that are

sounds as though the brake light switch is stuck it's down behind the brake pedal arm try removing it and cleaning around the plunger where it goes into the switch also look at and see if the plunger has became bent from years of use you may need to just replace the switch.

Posted on Dec 28, 2009

  • 92 Answers

SOURCE: i have a 2002 ba falcon my abs light comes on and

The wheel bearing needs to be replaced (hub assembly) Its dangerous.

Posted on Jan 01, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My brake pedal is sitting too high on my au series 2 just replaced brake booster with a ba v8 brake booster can anyone help me please :


i was wrong no pedal height adjustment ??

AU to BA falcon forum
fordforums com au

repair manual one download allowed only not for resale etc etc
1b118bf5-0c8f-43fa-8cb6-32cb85feafdf.jpg

Oct 17, 2016 | Cars & Trucks

1 Answer

Change bulb 2004 ford falcon ba xr6


Remove the battery if it is RH side bulb then remove dust cover and you are at the rear of the bulb

Apr 30, 2014 | 2005 Ford Falcon

1 Answer

We're is fuse for brake lights? I don't have a owners manual to look at its a ba falcon


Google ba falcon fuse diagram & click on the images. I thought the images weren't clear but when you click on them they are. Hope this helps!

Jan 01, 2013 | Cars & Trucks

1 Answer

Left brake light on falcon ba not worken i put new bulb still not worken Any ideas thank you


Possible problem with the light socket ? Bad ground connection ?

Jun 27, 2012 | Cars & Trucks

2 Answers

I need a manual for a 2004 Ford Falcon BA Futura


Hello,
Please kindly follow the link below to get the manual you requsted for;
http://fitripdf.com/books/ba-gt-ford-falcon-service-manual-2.html


thank you for using fixya

Dec 19, 2010 | Ford Futura Cars & Trucks

1 Answer

Rear side brake lights won't work after fuses/bulbs replacement


If the high level brake lamp works and the other 2 lamps have good bulbs, then there is a power loss, most propably with the installation. You should go to an auto electrician to see where the break is.
If someone has recently done any work on the electrics, you should recheck. It is not a seperate fusable power supply system or brake switch for the high level brake lamp, it will take its power from the fused system that the other 2 have.
Hope this helps

Oct 04, 2009 | 1998 Land Rover Discovery

2 Answers

My high level brake light has bruned out,(third brake light). I was informed by the dealer the back window panel has to be removed to replace the 3.00 dollar bulb, total cost 75.00 dollars. With some


replace the bulb...??? This requires you remove the rear package deck (to access the bulb & socket). to do this, remove the seat bottom (two bolts hold the rear seat bottom to the chassis, then remove the bolts which hold the shoulder cushions (LH & RH - 12mm bolts) then remove the cosmetic molding around the trunk access (7 to 8 screws) then remove the "C" pillar covers (SRS curtain airbag LH & RH) to access the rear deck package & access the third brake lamp bulb. replace it, then reassemble.

May 26, 2009 | 2006 Hyundai Sonata

1 Answer

High Level Brake bulb replacement


If memory serves, there are two screws holding this light assy to the rear package deck. They are covered (LH and RH side of this assy). remove the covers and using a phillips screwdriver, remove the screws and lift the assy up and away from the rear glass. you now have access to the bulb and socket.

May 18, 2009 | Hyundai Motor 2004 Accent

2 Answers

Changing rear brake bulb for a ford falcon EL


I have a '98 build EL Falcon. If the tail light assembly hasn't been out before, inside the boot there are these 2 locating pins coated in plastic. These are attached near the outer edge of the assembly, running inside the boot. The square shaped hard plastic bits protruding inwards are for screws to attach to - so don't remove these. I had to get the plastic off to free the locating pins to remove the assembly. The second part is the 2 screws towards the reverse light end of the assembly. You access these from the outside of the car. Once these are undone the assembly should come out far enough to access the bulbs - as wiring is attached. There are 3 accessible bulbs available to replace. The brake light and the indicator bulb holders are in line with each other and you twist them out of the assembly, then remove the actual bulb and replace. To replace the assembly, put the locating pins into position and then the rest until sitting correctly and re-install the 2 screws.

May 08, 2009 | Ford Fairmont Cars & Trucks

1 Answer

Hyandia Accent


not sure which top tail light you mean? do you wish to replace bulb or actual lamp on the rear screen? this is the high level brake light ! OR do you wish to replace bulb in one of the rear tail lamps offside/nearside ? which ever ? the h/level brake light bulb is accessable for bulb from the rear panel on hatch behind lamp bulb is 16 watt capless push in type

Nov 10, 2008 | 2003 Hyundai Accent

Not finding what you are looking for?
2005 Ford Five Hundred Logo

Related Topics:

134 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5467 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...