Question about 1994 Mitsubishi Montero

1 Answer

My 94 Montero shifting problem.

My 94 Montero had an electrical problem that I've fixed but I'm pretty sure it fried the shift-control module for the transmission. Where can I send it to be rebuilt reasonably and reliably? Thanks.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 523 Answers

It may be tough to have this rebuilt; I'd look to a wrecking yard, ebay or craiglist to find a used one. In the end this probably be a cheaper route with good results.

I hope this may have assited you,
Tom

Posted on Nov 20, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

When i put my car in park or drive it feels like it is hard to move the shifter. 2008 saturn aura


Safety system , shift lock . Has locking solenoid's that won't allow shifting from park to gear without the diver pressing on the brake pedal . Electrically controlled , brake switch , body control module .
Your best bet would be to take it to a qualified repair shop .
The automatic transmission shift lock control system is a safety device that prevents an inadvertent shift out of PARK when the engine is running. The driver must press the brake pedal before moving the shift lever out of the PARK position. The system consists of the following components:
• The automatic transmission shift lock solenoid (serviced as the automatic transmission shift lock actuator), as well as the body control module (BCM) and the engine control module (ECM). The shift lock solenoid is located within the floor shift control assembly with vehicles equipped with floor shift.
• The BCM controls the voltage supply circuit of the shift lock control solenoid. The following conditions must be met before the BCM will supply voltage to the shift lock control solenoid.
The BCM controls the voltage to the shift lock control solenoid through the shift lock control solenoid controlled voltage circuit. The following conditions must be met before the BCM will supply voltage to the shift lock solenoid:

Sep 19, 2017 | Saturn Cars & Trucks

1 Answer

2005 gmc sierra 4wd warning light on and will not shift into 4wd


been here /transfer case control module/ electric -shift /actually easy fix /under left sideof instrument panel.behind headlight switch.if thats not it/electric shift motor and encoder assembly /sounds confusing but its easy fix to .get u a repair manual youll see.good luck.

Jan 08, 2013 | 2005 GMC Sierra

1 Answer

I have a 1994 ford tempo that has issues shifting. It starts fine goes into all gears . it shifts from first to second gear at 35mph then shifts again at 45mph. What could be the issue? I changed the...


You may need a transmission shop for this.
Some older cars used a vac modulator to control shift time, but I don't see one listed for a 94 Tempo. Whatever Ford uses to control shift time may be faulty, or the kickdown cable to the throttle body may be sticking. It could have a solenoid inside that does what the modulator once did.

Dec 12, 2012 | 1994 Ford Tempo

1 Answer

Transfer case grinds truck only runs in 4wheel low nothing in 4wheel high or 2wheel drive


Manual or electronic t case?

Section 07-07: Transfer Case, 4x4 System, Service 1994 Bronco/Econoline/F-Series Workshop Manual
DESCRIPTION AND OPERATION Electronic Shift Operation The transfer case is equipped with a magnetic clutch, similar to an air conditioning compressor clutch, which is located inside the transfer case adjacent to the lockup collar. The clutch is used to spin up the front drive system from zero to vehicle speed in milliseconds. This spin-up allows the shift between 2-high and 4-high to be made at vehicle speeds listed in the vehicle owner's guide. The spin up engages the front lock hubs. When the transfer case rear and front output shafts reach synchronous speed, the spring-loaded lockup collar mechanically engages the mainshaft hub to the chain drive sprocket and the magnetic clutch is then deactivated. Shifts between 4-high and 4-low can only occur with the transmission safety switches closed. The vehicle's speed must also be within specified limits as determined by the transfer case speed sensor (3 mph or under). Electronic Shift Control System
This system consists of a two-switch control system, an electronic control module, an electric shift motor (7G360) with an integral shift position sensor, and a speed sensor. Switch Control System
There are two control switches located on the upper right corner of the instrument panel for fingertip shift control. The two switches are mounted horizontally and are identified as "4x4" and "LOW RANGE". Two indicator bar lamps are located in the instrument cluster.

c11148a.gif

When either of the two switches on the instrument panel control are depressed, the first thing that happens is that the electronic control module receives input from the transfer case shift position sensor to verify what position the transfer case is in (2H, 4H or 4L). Next, the electronic control module looks at the speed sensor and the park/neutral position switch or clutch pedal position switch (depending on transmission type). If all conditions are correct to allow the desired shift, the electronic control module will tell the electric shift motor to execute the shift. After the shift has been made and the electric shift motor is off, the control module again looks at the shift position sensor to make sure the proper shift has been accomplished. Finally, the dash indicator light and the pushbutton light on the control panel will be illuminated by a signal from the electronic control module indicating the desired function has been completed.
Electronic Control Module
The electronic control module, located on the passenger side, controls the operation of the transfer case in response to inputs to the pushbutton control by the vehicle operator, the speed sensor, shift position sensor and the park/neutral position switch. Speed Sensor
The speed sensor, mounted on the rear of the transfer case , tells the electronic control module the speed of the vehicle to allow range shifts (in or out of 4L) to occur. Shift Position Sensor
The shift position sensor, an integral part of the electric shift motor , tells the electronic control module the shift position of the transfer case . Electric Shift Motor
The electric shift motor , mounted externally at the rear of the transfer case , drives a rotary helical cam which moves the 2W-4W shift fork and 4H-4L reduction shift fork to the selected vehicle drive position.

Nov 12, 2010 | 1994 Ford F250 Supercab

1 Answer

Dies when shifted in to drive 94 bronco


pcm problem. the EEC has some control on the transmission. PCM- power train control module. EEC IV Electric engine control. they both play together. Check engine light on

Sep 28, 2010 | 1994 Ford Bronco

1 Answer

Does not shift from 1st to 2nd to 3rd...


It have valve bodies that control shifting. The only way to properly correct is to rebuid trans

Jan 06, 2010 | 1994 Ford Explorer Limited

1 Answer

Trans


replace the Vehicle speed sensor (VSS) on the transmission, it senses when trans should be shfited to overdrive by the Transmission control module.

Oct 06, 2009 | 1991 Mitsubishi Montero

2 Answers

94 dodge neon auto tranny


Hi,

Here is some possible reasons why your transmission is having those problems .

* The gear shift linkage is binding
* There is an internal problem in the transmission
* The throttle cable is broken or disconnected
* The vacuum modulator on the transmission is faulty or the vacuum line is damaged
* The electronic transmission control circuit may be faulty

Feb 26, 2009 | 1995 Dodge Neon

1 Answer

I need to locate the 4 wheel drive control module on a 2002 Chevy Silverado. can you tell me where to look


  1. Remove the IP trim bezel.
  2. Pull out the lamp switch, 4WD shift buttons, cargo lamp and air deflector louver assembly in order to disconnect the electrical connectors.
  3. Disconnect all the electrical connectors from the lamp switch, cargo lamp and 4WD shift buttons assembly.
  4. Remove the lamp switch, 4WD shift buttons, cargo lamp and air deflector louver assembly from the vehicle
  5. Remove the electrical harness retainer from the IP support beam.
  6. Disconnect the 2 electrical connectors from the transfer case shift control module.
  7. Move the electrical harness to the left side in order to make room to turn the transfer case shift control module.
  8. Rotate the transfer case shift control module about 45 degrees counter clockwise while pulling out at the same time until the module is approximately 90 degrees from the original position.
  9. Pull out the module from the vehicle

Jan 02, 2009 | 2002 Chevrolet Silverado

2 Answers

1994 Dodge Spirit Automatic Transaxle


Yes the computer uses TPS (throttle position sensor) and VSS (vehicle speed sensor) sensors information as well as fluid temp and other factors to determine shift points based on the info stored in the PROM (memory) IC chip, if it is not shifting then you either have a poor connection at the trans case electrical connector or a sticking shift solenoid inside the trans, I would pull the trans connector off and make sure it is clean and properly installed, look for a broken connector retainer as well, this is very common and can cause a loss of signal from the PCM (power train control module) module to the transmission shift solenoids. Most likely the 3rd gear shift solenoid is sticking off from sitting so long, had this happen on my truck, cleared itself.

Sep 18, 2008 | 1994 Dodge Spirit

Not finding what you are looking for?
1994 Mitsubishi Montero Logo

121 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

77202 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8743 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...