Question about 2004 Mazda 6

Open Question

Wiring diagram for fog light install

Wiring diagram for fog lights install on 2005 mazda 6i with sport bumper

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

ButtFuzz
  • 463 Answers

SOURCE: i need a wiring diagram for fog lights oem to my toyota

The link below is a Typical fog lamp / driving lamp hookup. Keep in mind that in most states, for these lamps to be 'legal' (and thus pass inspection), you must wire them such that:

1. You can cut them off (in other words, there must be a switch installed to turn them off)

and

2. They may only be operated with the low beams. (therefore, you must power your on/off switch from the low beam circuit)

http://www.accessconnect.com/fog_driving_lights_wiring.htm

Posted on Feb 28, 2009

rogrrabbit
  • 986 Answers

SOURCE: need a tail light wiring diagram for 2005 Jeep Liberty

I advice you don’t cut into the wiring harness but get the proper kit that is plug and play.

Posted on Jun 14, 2009

bschilz
  • 2049 Answers

SOURCE: serpentine belt diagram mazda 6 2005

Here are links to the diagram...

If your engine is the 2.3L 4 cyl... http://www.gates.com/common/part_locator/view_diagram.cfm?id=S7042

If your engine is the 3.0L V6... http://www.gates.com/common/part_locator/view_diagram.cfm?id=S6036

Posted on Sep 01, 2009

dttech
  • 4803 Answers

SOURCE: how can fix code P0703 on mazda 6i v6 2005

The conditions that set this code are as follows:

The PCM monitors changes in input voltage on Brake Switch No. 1. If the PCM does not sense voltage changes at PCM terminal 82 when alternately accelerated and decelerated 8 times, the PCM determines that brake switch No. 1 has a malfunction

Possible Causes are:

  • Brake Switch malfunction
  • connector or terminal malfunction
  • Short to power circuit between Brake Switch terminal D and PCM terminal 82
  • Open circuit between Brake Switch terminal D and PCM terminal 82
  • Malfunctioning PCM

Posted on Nov 11, 2009

  • 2 Answers

SOURCE: change fog light bulbs in Mazda 6

Hi, I have a 2003 Mazda 6 which also has the fog light in the headlight assembly. I'm not sure but I would imagine the design is similar to yours. I had the left side blown and it took me roughly 10 minutes to get the bulb out. The cover on the back of the assembly has a push tab in the centre at the top and two locating tabs on the bottom. I had to push down fairly hard on the air filter side of the top tab while at the same time carefully levering the cover off with a flat blade screwdriver. There isn't a lot of room between the headlight and the air filter box but just enough that you can tilt the back cover over a bit and lift it straight up, out from the bottom locating tabs. Pull this cover right out and then you can see inside the back of the headlight assembly. The bulb has a wire retainer clip that you can push in with your fingers to unhook it and hinge it over. You may have to pull a wire terminal off to get at this clip better.You can now just pull the bulb out and remove the approx 5cm wire tail on the bulb out from it's terminal. Should be able to get a replacement bulb just about anywhere. Replacement would be the opposite only be careful not to touch the glass of the bulb with your fingers as this is detrimental to the life of the bulb. Don't forget to put the other wire terminal back on if you had to remove it. As far as the right side goes, I have never replaced the fog light but I have replaced the headlight bulbs which are also behind this cover so it should be possible. It was a while ago for that but if I remember rightly, I had to use a little mirror sometimes on the right headlight-bit of a pain. By the way, unlike me, before you ever replace a headlight bulb, check that the fuse isn't blown first. There is a fuse for low and high beam for both left and right headlights. I don't think that is the case with the fog lights. Hope this helps you or whoever else.
Cheers,Peter.

Posted on Mar 05, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Driver side fog light wont stay on


CLearly a connecting issue. Check wiring pins

Mar 12, 2014 | Mazda MAZDA3 Cars & Trucks

1 Answer

The best way to replace the headlght bulb


In my opinion, the BEST way is to get somebody else to do it for free!...LOL

However, that is not very likely to happen in this millenium, so I have provided the pictures below.

Also please note that there is a Mazda 6i and a Mazda 6s But there is no Mazda MX6 in 2005. There is, however, a Mazda MX5...so assuming this is what you meant, the pictures are for the MX5.

If you meant Masda 6i or Mazda 6s, these pictures are not even close because the 6-series requires removal of the front bumper to remove the head lights.


12_4_2011_2_50_48_pm.jpg

12_4_2011_2_51_44_pm.jpg

Dec 03, 2011 | 2005 Mazda MX6

1 Answer

Can factory foglights be installed in a 2008 Hyundia Veracruz? Knockouts are in the bumper and a knockout is in the dash. Is the existing wiring harness ready to just plug the fog lights in under the...


Not sure about Veracruz, but most of modern cars have the harness pre-installed to have additional factory things fitted, my Trajet had a plug behind the bumper, my Mazda had a plug for fog light just above the front wheel behind a cover. So I presume that your vehicle will have the same.

Feb 10, 2011 | 2008 Hyundai Veracruz

1 Answer

Need a fuse box diagram to wire in fog lights


Fog lamps are installed on the front bumper. The switch is located to the left of the steering column on the dash panel. The fog lamps are turned off by the circuit relay when the high beam driving lamps are turned on. The circuit relay is located on the right front wheelhouse panel near the blower motor.

Good luck, and remember rated this help.
Removal & InstallationFog Lamp Element
See Figure 1
558610d.gif
Fig. 1: Exploded view of a fog lamp assembly

  1. Remove the lamp stone shields, the four bezel attaching screws, and the bezel.
  2. Remove the reflector assembly from the lamp body.
  3. Remove the bulb holder from the assembly. Remove the element from the bulb.

DO NOT handle elements with your bare hands, always handle with a clean cloth. Oil from your hands will cause the element to fail.
  1. Installation is the reverse of removal.

Fog Lamp Switch
The fog lamp switch is removed and installed by simply prying the switch from the instrument panel and unplugging the electrical connector.
FOGLAMP BEAM ADJUSTMENT

  1. Position the vehicle on a level surface, facing a wall approximately 25 feet away. Remove the lamp stone shields and loosen the adjustment nuts.
  2. Turn the fog lamps ON and adjust as follows:
    1. Distance between the light beam centers should be equal to the distance between the lamp assemblies on the bumper.
    2. Height of the light beams on the wall should be 4 inches less than the center of the lamp assemblies when mounted on the bumper.
  3. Install all previously removed items after turning OFF the fog lamps.

1995 Cherokee Chassis Schematic
8e08df0.gif

www.autozone.com

Aug 11, 2009 | 1995 Jeep Cherokee

2 Answers

I need a wiring diagram for fog lights oem to my toyota


The link below is a Typical fog lamp / driving lamp hookup. Keep in mind that in most states, for these lamps to be 'legal' (and thus pass inspection), you must wire them such that:

1. You can cut them off (in other words, there must be a switch installed to turn them off)

and

2. They may only be operated with the low beams. (therefore, you must power your on/off switch from the low beam circuit)

http://www.accessconnect.com/fog_driving_lights_wiring.htm

Feb 28, 2009 | 2005 Toyota Corolla

1 Answer

Need wiring shematic for fog lights 2005 toyota corolla


im pretty sure these cars were already prewired for fog lights .there should be some plugs behind the bumper to fit them.if not get back i will explain how to wire them up.best of luck.

Sep 04, 2008 | 2005 Toyota Corolla

2 Answers

How do I change fog lights on my 2005 durango


On my Durango ther was one long screw that pivoted the broken unit out. Unscrew the one screw until it comes out. I found this out after removing my bumper cover. Good Luck Hope this helps

Aug 02, 2008 | 2005 Dodge Durango

Not finding what you are looking for?
2004 Mazda 6 Logo

Related Topics:

427 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7726 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...