Question about 2006 Nissan Murano

1 Answer

How do i access the fog lamps - 2006 Nissan Murano

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 819 Answers

You need to remove the splash panel under the bumper around the fog light area. you can then reach up and the bulb should twist out. its a little tricky and hard on the wrists.

Posted on Nov 20, 2009

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 840 Answers

SOURCE: Changing fog lamp in 2002 corvette

you need to take off the lower splash sheilds on bumper they are retainer or bolted 10mm or retainers just pull the center and then pull out/ Please rate my response thank you very much

Posted on Jan 31, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace bulb on fog lamps suzuki xl7 2003


this info is in the operators guide, lost that? in the glove box.
my 07 manual shows no fog , lamp instructions
it says contact dealer and as you know they are DOA. Chapter 11.
any mech can do this..
some fogs are optional added lamps to some years, and makes and in some countries (not stated)
but in general its 3 ways.
Look at the lamp , see it?
does the front have screws on the lens. , remove it.
if not its a rear access lamp
gain access to the rear and remove the socket, and replace the lamp,
if all this is too hard, and still a wana DIY,
you could go to alldata.com and read how. under lighting,.
or post a photo of said fog lamp.. my 04 has no such lamp. BTW.
if the lamp need body panel removal. then in the FSM (or above link) you'd read the section under body. for how todo that.

Oct 17, 2013 | 2002 Suzuki XL-7

1 Answer

I have toyota 2011 RAV4.and want to know how to install fog lamps and new wireing


This is a social web site,not an automotive
repair shop or tech line, with access to free info

On the fog lamp assy,I would crawl under a similar
vehicle & see if all you need to do is remove a cover
plate or drill some holes

On the wiring,I think the dealer parts dept will provide
some harness, that should plug in somewhere on yours

May 24, 2012 | 2011 Toyota RAV4

1 Answer

2003 buick regal fog lamp replacement


For fog lamp replacing procedure,click the link below :---http://technoanswers.blogspot.in/2012/03/to-access-back-of-fog-light-there-is.html
--------This will help.Thanks.

Mar 05, 2012 | 2003 Buick Regal

1 Answer

How do I replace the fog light? what needs to be removed to access fog lights and side marker lights.?


SECTION 417-01: Exterior Lighting 2000 Taurus/Sable Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 08/27/1999 Fog Lamp Removal and Installation
  1. Raise and support the vehicle. For additional information, refer to Section 100-02.
  1. Remove the aeroshield-to-sub frame screws.
    a0008736.gif
  1. Remove the seven screws and remove the aeroshield.
    a0009383.gif
  1. Disconnect the fog lamp assembly electrical connector.
    a0011782.gif
  1. Remove the fog lamp assembly.
    1. Remove the screws.
    1. Remove the lamp assembly.
    a0011783.gif
  1. To install, reverse the removal procedure.

2010&c18=modelyear&c20=n161420&c35=wsm%2cfog%20lamp%2csyh%2c417-01%2cremoval%20and%20installation&s=1249x702&c=32&j=1.3&v=y&k=y&bw=910&bh=359&ct=lan&hp=n&[aqe]

Mar 05, 2011 | 2000 Mercury Sable

1 Answer

Fog lamp replacement


there is an access panel located in the wheel well,behind the fog light. it has plastic screw heads ,they don't turn out so just pry them out and u can reuse them . the fog light is now accessible

Nov 22, 2010 | 2007 Hyundai Santa Fe Limited

1 Answer

I need to replace a foglamp bulb right side.I have fairly easy access to & can see the rubber housing for the bulb,but cannot figure out how to remove it.Do I need to rermove the entire assembly in...


Typically the fog lamp is located in the front bumper assembly. It's usually fairly easy to access and replace these.

Place the car is park, secure parking brake. Use a creeper to scoot under the front end of the car, look up into the bumper. Located the backside of the fog lamp holder. You would usually grab and twist counter clockwise about an inch, then pull straight out. Push in on the bulb while turning counter clockwise until it pulls out of the lamp holder.

These fog lamps usually have a little bit of cushioning grease in the socket. Do not remove the grease or connectivity problems will result with the new fog lamp. Push the new bulb in, turn clockwise until bulb stops turning, release hand pressure.

Installation is the reverse of removal.

May 25, 2010 | 1999 Oldsmobile Eighty Eight

1 Answer

How to replace fog light bulb on an '03 Jeep


There is a small square "trap door" in each wheel well directly behind the fog lamps. You can pry it open and access the fog lamps. They just twist loose.

Feb 11, 2010 | 2003 Jeep Wrangler

1 Answer

How do I replace the fog light assembly on a 2000 Olds Alero?


you replace the fog lamps by going under front bumper fascia.remove the pushpins and take down the splash shield to access the back of the fog lamps.then you remove two bolts retaining the fog lamp to the back of front bumper.besure to wear clean gloves.because fog lamps is halogen bulbs.if you touch with bare hands the oils from hands will make the bulbs over heat and blow out.

Dec 03, 2009 | 1999 Oldsmobile Alero

1 Answer

Fog lamp assembly


I apologize if i had not answered this earlier... if the lamp is mounted in the bumper you often have to remove the plastic covering on the bumper to gain access.

you can also try to see if there are mounting bolts that you can access under the car and to the rear of the lamp.

Robert

Sep 05, 2008 | 2005 Ford Escape

1 Answer

HOW TO REPLACE HEADLIGHTS ON 2000 CHRYSLER LHS


ATTN: NIKKICARROLL

here is how to replace the bulb in your vehicle


  1. Release the hood latch and open the hood.
  2. Remove the radiator closure panel sight shield as necessary to gain access to the headlamp.
  3. Remove the screws holding the headlamp module halves together.
  4. Separate the module halves.
  5. Disengage the wiring from the headlamp bulb.
  6. Remove the retaining ring from the back of the headlamp bulb.
  7. Pull the bulb from the lamp.
To install:
  1. Push the bulb into the lamp.
  2. Install the retaining ring to hold the bulb in the lamp.
  3. Engage the wire connector to the back of the headlamp bulb.
  4. Place the module into position on the vehicle.
  5. Install the screws to hold the module to the vehicle.
  6. Install the radiator closure panel sight shield.
  7. Check the headlamp alignment and operation.
88176gb1.gif Exploded view of the fog lamp with the bulb removed
Click to Enlarge

  1. Release the hood latch and open the hood.
  2. Remove the radiator closure panel sight shield as needed to gain access to the headlamps.
  3. Remove the screws holding the headlamp module halves together.
  4. Separate the halves.
  5. Remove the fog lamp wire connector cover.
  6. Disconnect the wires from the fog lamp bulb.
  7. Disengage the retainer clip holding the bulb to the fog lamp.
  8. Remove the bulb from the fog lamp.
To install:
  1. Place the bulb into position in the fog lamp.
  2. Engage the retainer clip to hold the bulb to the fog lamp assembly.
  3. Attach the wire connectors to the fog lamp bulb.
  4. Install the fog lamp wires connector cover.
  5. Place the module halves together.
  6. Install the screws to hold the headlamp module halves together.
  7. Install the radiator closure panel sight shield.
  8. Verify the fog lamp operation and alignment

ATTN: WDSNEED1

Removal & Installation 88176g87.gif Remove the screws retaining the headlamp module to the mount adapter
Click to Enlarge

  1. Release the hood latch and open the hood.
  2. Remove the radiator closure panel sight shield as necessary to gain access to the headlamp fasteners.
  3. Remove the screws holding the headlamp module to the mount adapter.
  4. Separate the headlamp module from the mount adapter.
  5. Disengage the wiring from the headlamp and foglamp.
  6. Remove the headlamp from the vehicle.
To install:
  1. Attach the wires to the headlamp and foglamp assembly.
  2. Place the headlamp module into position on the mount adapter.
  3. Install the screws to hold the headlamp module to the mount adapter.
  4. Install the radiator closure panel sight shield.
  5. Check the headlamp alignment and operation.

Jul 28, 2008 | 1994 Chrysler New Yorker

Not finding what you are looking for?
2006 Nissan Murano Logo

Related Topics:

95 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

723 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...