Question about 2005 Dodge Neon

1 Answer

Check engine lite came on, cam sensor was replaced. Should anything else be checked/changed? Any problem with the cam shaft now? 2005 Dodge Neon. Also, all the door handles/latches stick. One has had to be replaced all ready. WD40 has helped to a certain exent, but does not loosen them to the point where they work right. Bought the car new, do not recommend it.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 422 Answers

No problems with the cam these sensors just go out sometimes and for the door handle (made in china)

Posted on Nov 20, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 2005 dodge neon that will crank but wont start. I have replaced the cam shaft sensor, crank sensor and the coil pack. Iam also not getting spark to the coil pack. Any suggestions?


Primary voltage to several systems, including the ignition coil, dark green wire with orange tracer. That voltage comes from asd relay. There is a fuse for asd relay. To check for voltage the engine has to cranking. The control side of asd relay, the computer has to ground it before it will energize. Did you check wiring circuits for cam and crank sensor connectors before replacing sensors? Are there any applicable trouble codes?
Are you ok with testing wiring circuits?

Feb 16, 2017 | 2005 Dodge Neon

2 Answers

Turn on ignition turn key to start position and engine is not cranking over


run the fault codes to check cam/crank position sensor. Check that the cam shaft is turning (broken timing belt /chain) check immobiliser operation

Aug 16, 2014 | 2005 Dodge Neon

1 Answer

I have 2 engine codes on my 2005 dodge neon. they are p0325 and p0340. the car has problem starting and misses badly for a while. What is the problem and how do i fix it? thanx for the help!


the p0325 code pertains to a knock censor. the p0340 is for your cam shaft sensor. i've had this problem before. try replacing the cam shaft censor first and run the codes again to see if the other still comes up. it should fix the problem. hope this helps

Jun 24, 2014 | 2005 Dodge Neon SXT

3 Answers

My 2005 dodge neon sxt wont start, no spark, changed cam shaft sensor, coil is good, cant find the crankshaft sensor, also wondered if it could be the timing belt, what do you think?


the crank sensor is on the back side of the engine just above the oil pan there will be two sensors there one is the crank sensor and the other is oil presser sensor. All so check the wires from the crank sensor to the cam sensor. If you think it is the timing belt pull the cover and check it. hope this helps.

May 22, 2012 | 2005 Dodge Neon SXT

1 Answer

2000 dodge neon will not start unless the cam shaft sensor is unplugged


I would go and but a cam sensor from the dealer. Aftermarket cam sensors can be slightly irregular. I had this happen to me with an aftermarket ABS sensor on a chevy. The whole problem was a gap difference equal to two sheets of paper. Whats happening is there is an open circuit in your old sensor that causes the check engine light but the new one has a good circuit but bad reading. I would say that is your problem.

Jan 29, 2012 | 2000 Dodge Neon

1 Answer

Crank shaft sesor/cam sensor problem?


If you had a fault with the crank sencer your car would not start.Sounds like the air flow meter is giving you the problems.

May 28, 2009 | 2005 Dodge Neon

1 Answer

Cam sensor causing other probelems


the cam sensor definitly can cause the problem. pull the trouble code and make sure the check engine light is for the cam sensor. if so, replace it and retest

May 11, 2009 | 2005 Dodge Neon

2 Answers

Blinking Check Engine light


This is typically a sign of a "detrimental misfire". A blinking check engine light means DON'T DRIVE ME! You may want to have your coil pack checked, plugs replaced or gapped properly, or wires replaced. Would also have to do with the camshaft sensor causing your timing to be off.

Mar 17, 2009 | 2002 Dodge Neon

2 Answers

Cam timing


usually when that code comes on after a belt change its because the cam or crank gear moved during tensioning,the cam and crank sensors are not in sync

Jan 18, 2009 | 1998 Dodge Neon

Not finding what you are looking for?
2005 Dodge Neon Logo

215 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8210 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...