Question about 1992 Mitsubishi 3000GT

2 Answers

1991 mitsubishi 3000 hard to start when cold.

Posted by on

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 560 Answers

There should be a 2 pin sensor located in or near to the thermostat housing. This sensor informs the ECU of the engine temp. If faulty it won't choke when cold so it would become difficult to start.

Posted on Nov 19, 2009

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Mitsubishi Master
  • 17,970 Answers

Keep in mind, this is a general diagnosis. Your car may not have the parts we list as potential problems. If you're not sure if your car has a particular part, check your owner's manual, service's manual or visit your mechanical service.

1991 mitsubishi 3000 hard to start when cold. - d838295.jpg

Hope helped with this. Good luck (remember rated this help).

Posted on Nov 19, 2009

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

witchertorqu
  • 63 Answers

SOURCE: 1991 mitsubishi might max hard to start when its

problems with the choke, to low fuel float level in carburator, timing to retarded or just problems with your battery or starter if it doesnt crank fast enough

Posted on Dec 08, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1991 mitsubishi mighty max want start in cold weather but will when its warm outside what could be the problem?


if this is carb motor than it needs a manual choke that mounts on inside of lower dash, the kind you see on lawn mowers,,,push and pull.

Mar 11, 2011 | 1991 Mitsubishi Mighty Max

1 Answer

The oil sensor lite is on and the oil gauge is reading zero on the tach we just replaced the crank and rods, the car is hard to start and hasnt ran in a while it has been a project car, when the car does...


you need to find the oil pressure sending unit and wiring that threads into the block and see if its plugged in, if it is, get an oil pressure tester that threads into place of the sender and check for oil pressure.

Jan 27, 2011 | 1991 Mitsubishi 3000GT

3 Answers

I need firing order diagram for 1991 mistubishi 3000 gt vr4


1991 Mitsubishi 3000GT AWD 3.0 liter DOHC V-6

14f3d03.gif

Hope helps (remember rated this).

Jul 21, 2010 | 1991 Mitsubishi 3000GT

1 Answer

Motor quit running


check timing belt if broke ??? maybe crank sensor ??

May 31, 2010 | 1994 Mitsubishi 3000GT

1 Answer

1991 mitsubishi might max hard to start when its cold out side.the colder the harder.now it wont start at all and its real cold!


problems with the choke, to low fuel float level in carburator, timing to retarded or just problems with your battery or starter if it doesnt crank fast enough

Dec 08, 2009 | 1991 Mitsubishi Mighty Max

2 Answers

Hard starting when cold ( engine cranks normally )


see if your engine has a ECT sensor (temp sensor that delivers information to your ECM) they are installed on the intake side of the cylinder head, it usually has 2 cables, have it checked replace if necesary

Nov 19, 2009 | 1991 Jeep Wrangler

1 Answer

Torque specs for mighty max


Per my Chilton's manual tehe bolts should be (cold engine) 65 to 72 FT. Pnds., the cam shaft bearing bolts should be 8x25 = 15 - 19 Ft pnds and the 8x65 should be 14 - 15 Ft Pnds.

The sequence is as follows for the (10 ) head bolts:

7 - 5 - 2 - 4 - 10

9 - 3 - 1 - 6 - 8

I hope this may help,
Tom

Oct 12, 2009 | 1991 Mitsubishi Mighty Max

Not finding what you are looking for?
1992 Mitsubishi 3000GT Logo

Related Topics:

193 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8210 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...