Question about 1993 Ford F150 SuperCab

1 Answer

Started my truck this morning..it was stalling out 2-3 times.. then the cluch pedel went to the floor. pulled it back up with my foot. now it is working fine. ?

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sergeant:

    An expert that hasĀ over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 205 Answers

Sounds like your clutch master cylinder, or slave cylinder or actuator seals failed. Most likely the actuartor. Check the clutch lines for fluid leaks. It could probably happen again and you might not be so lucky this time.

Posted on Nov 19, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

2004 f150 ,replaced all brakes and parts,replaced all flex lines.Worked fine for 3 months,pedal start feeling spongy again,we rebled the system again follow produce.Got 2 weeks out of it,now the pedel is...


If you haven't refilled the resovoir for the brake fluid and it's running out again you have a leak in hte brake line somewhere. Even if you replaced the brake lines you might still have a leak somewhere. It just takes time to find it

Thanks Terry

Mar 14, 2014 | Cars & Trucks

1 Answer

1999 dodge durango soft brake pedal only wen i start it


have someone have there foot on the brake & start vehicle, inspect the flexible brakelines to see if any are balooning out. You could also clamp off one flexible line at a time & press brake & when you find the brake at fault the pedal will go hard.

Oct 12, 2012 | 1999 Dodge Durango

1 Answer

Took RAV 4 to NC mountains and back twice this weekend. It ran fine but started it this morning and it would stall when I took my foot off gas pedal


I would change your fuel filter. The mountains, and the sudden jerking would provide a great chance for the fuel to pull up any nasties, and then run them through the line.

Dec 22, 2011 | Toyota Cars & Trucks

2 Answers

I was parked on the side of the road in my ford ranger ute for about 3 to 4 minutes with the clutch pedal to the floor i was on the phone and then i could smell the clutch burning. I took my foot off the...


The clutch might be a hydraulic system. When it's leaking oil the pedal sticks to the floor and has to be pulled back manually. Because it's designed to be fail safe, it still works but only for some time till all the oil has leaked out.

The burning smell might be clutch oil dripping on the exhaust - meaning the seal on the clutch servo is leaking oil.

There are repairkits for clutch servo's - usually it's suggested to replace the cylinder seal on the clutch pedal also.

Jul 01, 2011 | Ford Ranger Cars & Trucks

1 Answer

We just bought a 2000 Suzuki esteem, the problem is whenever we start the car, it becomes very difficult to shift between gears when the car is idle, but when the car is on the freeway, shifting works...


The cluch not fully disingaging , ( carpet under the pedel, pedel bent , bushing worn out of pedal, low on fluild in clutch master ( brake fluid ) and bad cluch master or slave or air in system. A damaged clutch will drag too. If it shifts OK with the car shut off standing still trans lube is likly OK too. If it has a clutch cable it may need to be adjusted pull up on the clutch pedal as high as it can go then pust down with your hand it should only go down an inch before it gets harder to pust down as it openes the clutch and shoul continue to go down about 4 or more inches. The pedal should be as high or a little higher than the break paedal. If not the pedal height may be needing to be adjusted higher. Some slave master hydrolic sysems aren't adjusted and have to be replaced to fix lack of enought movement Clutes that are hard to pust in or get much harder as you get closer to the floor the cluch is likly to be worn out and need to be changed with a new clutch kit and resurface the flywheel. The flywheel can change to unflatand the cluch can drag. engine oil getting into the clutch though a leak in the valve cover or rear main can get on the cluch and make it drag and grab.

Mar 21, 2010 | 1996 Suzuki Esteem

1 Answer

My 99 Expedition it act like it want to cut off while I'm drivivg


if u are getting a fault code saying it is the air flow sensor u need to replace it a reset the computer memory

the airflow sensor is between the throtle body and the the filter

once u have done that road test truck and check codes again

let me know how u went

Dec 21, 2008 | 1999 Ford Expedition

1 Answer

Clutch pedal goes to the floor(new clutch installed 2 wks ago)


that cable fited one side to cluch pedel and ather side fited gear box side where palte which is relecing clutch bearing. dont forget to adjust.

Dec 01, 2008 | 1985 Volkswagen Quantum

Not finding what you are looking for?
1993 Ford F150 SuperCab Logo

Related Topics:

89 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5520 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...