Question about Dodge Pickup

2 Answers

Spinning sound when pushing gas peddle, sitting

Spinning sound in engine when pushing gas peddle, when sitting still or moving.

Posted by on

  • MARCOS ACEVEDO May 11, 2010

    what year, model, engine, and where/what area spinning sound comes from?

×

Ad

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Mine was low oil, it was making this spinning sound, i added oil and it went away right away.

Posted on Jan 16, 2010

Ad
  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sergeant:

    An expert that hasĀ over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 226 Answers

Try it with the belts off you can start it and see if the spinning noise goes away then it's accessory's like bad alternator or power steering pump but dont run it more than a minute or two or it will start to overheat. and if it still makes spinning noise make sure it's not coming from the transmission /use a broomstick against the engine block near each piston to hear the condition of the pistons if there scored real bad it makes noticable diff noise than a diff piston will make. check the front of the engin the water pump sometimes needs to be replaced because the bearing in it drys up and fails / there sealed bearings in a water pump than go make noise . good luck give you stuff to think about.

Posted on Nov 19, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to reset accelerator on a 2012 dodge avanger


Try this. If tps is positioned correctly and idle is correct.

You can recalibrate the throttle yourself to eliminate flat spots or pauses in its response curve.

This should work on most Fly by wire cars, they work on chevy and dodge for a fact

1-ignition to RUN but do not start
2-wait until all the dash warning lights go out (engine light should be the only one to remain on)
3-slowly depress the gas peddle to the floor (take at least 15 seconds to gradually push it to the floor, do not waver as you push)
4-slowly release gas peddle to full up (again, take at least 15 seconds to gradually let it back up, do not waver as you let up)
5-ignition to off
6-DO NOT START IMMEDIATELY! Allow to sit for up to 10 mins+, then start and check for difference in response and linearity.

Sep 07, 2016 | 2012 Dodge Avenger

1 Answer

Car wont move


Check your throttle cable . sounds like it might be broken

Nov 11, 2013 | 1998 Lexus Gs 300

1 Answer

Looses power under a load put in neutral give gas runs good


sound like fuel filter stopped up.if you have distributor type engine your idle speed could be too low and ignition timing off a little.

Dec 11, 2011 | 1995 Toyota Camry

2 Answers

I cant push my brake peddle down ?


sounds like the break booster or master cylinder. Also maybe a vacumm issue with the break booster make sure the line is hooked from the booster to the engine intake

Feb 02, 2011 | 1992 Ford F250

1 Answer

When push brakes you have to push really hard to make them go in then the truck barely stops. Replaced the MC and bled the brakes now every time push brakes truck acts like its going to die. Brake light...


Sounds like you will have to bleed your brakes again, but thats not the problem og hard brake peddle, need to check your power brake booster, sit right in back of master cylinder, check make sure it has vacum going to it, also to test it with engine off, press on brake peddle three time, then state engine with foot on peddle, peddle should go down a few inches, also with engine of peddle should feel soft for three pumps, if you have none of this , power brake booster is bad.

Jul 04, 2010 | 1995 Toyota 4Runner

1 Answer

Car won't start


try this, if the car wont start push the pedal all the way to the floor and hold it ther while you crank. It sounds like you are flooding the car some how. Pushing the pedal to the floor puts the car into clear flood mode and it shuts off the fuel flow. try and see just a suggestion

Jan 18, 2009 | 1999 Ford Taurus

1 Answer

96 Jeep Grand Cherokee wont go into reverse


chheck your tranny fluid. if it's ok, probably need tranny work done.

Jan 10, 2009 | 1996 Jeep Grand Cherokee

1 Answer

I have a 95 Lincoln Continetal and I can't push the gas peddle down without force. When i pull the cable from the engine the peddle moves fine. Also when I try to move the throttle it will not move.


Hi if the cable is moving freely than it will be either the throttle body jammed or the throttle pedal has ceased, also check nothing has got jammed behind or above the pedal, hope this helps

Dec 10, 2008 | 1995 Lincoln Continental

1 Answer

1999 rodeo 6 cyl


hello from what you explained i take it theres no check engine lights on what it sounds like is a basic increase on your idle screw get somone to help push pedal down underhood look to see where gas cable pulls back when gas pedals appled have them release slowly now watch where it stops against a set screw that is your adjustment rpm range should be somewhere between 750-900 rpm depending on vehicle if this doesnt solve most likely tps sensor{ throttle position sensor} goodluck

Aug 10, 2008 | 1999 Isuzu Rodeo

1 Answer

Break/Gas peddles hit at same time


the Brake pedal is a huge Pedal. Move your foot over.. Be less lazy in your foot placement. Its an 08 so i'm assuming fairly new to you.. Its gotta be different from what your used too. Sit up straight, slide your seat up..move your foot over, and drive. Sleeping is for Beds..

Jun 17, 2008 | 2008 Ford F-350

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

178 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

79865 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...