Question about 1993 Isuzu Rodeo

1 Answer

Replacing a new starter on a 93 isuzu rodeo - 1993 Isuzu Rodeo

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Isuzu Master
  • 2,984 Answers

Don't know what size motor you have because you didn't post it so please pick the proper one:

This is for the 4 cylinder motor--

replacing a new starter on a 93 isuzu rodeo - 8e64f3e.gif
4-cylinder engine starter connections



  1. Disconnect the negative battery cable.
  2. Raise and safely support the vehicle on jackstands.
  3. If equipped, it may be necessary to disconnect and remove the EGR pipe to access all the starter bolts.
  4. Tag and disconnect the starter battery and control wiring at the starter.
  5. If equipped, remove the starter bracket and/or heat shield.
  6. Remove the starter-to-engine bolts.
  7. Move the starter away from the engine and down to remove from the vehicle. Some starter may be installed with shims between the starter and engine. When the starter is removed, these shims may fall out. Do not loose them.
To install:
  1. Install the starter and shims, if equipped to the engine. Align the mounting bolt holes and insert the bolts. Hand-tighten the bolts.
  2. Tighten the starter mounting bolts to 30–34 ft. lbs. (39–44 Nm).
  3. Install the starter bracket and/or heat shield, if equipped.
  4. Connect the battery and starter control electrical wires to the starter.
  5. If the EGR pipe was removed, install it.
  6. Lower the vehicle.
  7. Connect the negative battery cable.
  8. Start the vehicle to make sure the starter functions correctly.
This is for the V6 motor--

8fdc27b.gif
6-cylinder engine starter installation


  1. Disconnect the negative battery cable.
  2. Raise and safely support the vehicle on jackstands.
  3. Label and disconnect the battery and starter control wires from the starter.
  4. If equipped, remove the starter bracket and/or heat shield.
  5. Remove the starter-to-engine mounting bolts.
  6. Lower the starter from the engine. If any shims are present, keep them for reinstallation purposes.
To install:
  1. Install the starter and shims, if equipped, to the engine. Tighten the mounting bolts to 30–34 ft. lbs. (39–44 Nm).
  2. Install the starter bracket and/or heat shield, if equipped.
  3. Reconnect the electrical connectors to the starter.
  4. Lower the vehicle.
  5. Connect the negative battery cable.
  6. Start the vehicle to make sure the starter functions correctly.

Posted on Nov 19, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What does the starter relay fuse for a 1998 Isuzu rodeo look like and where is is located in the fuse box


Crystal, this is what I found on the Rodeo starter fuse/relay.
Check the attached links,instruction and guides, Good luck
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."
99 Isuzu Rodeo LS Underhood Fuse Box Diagram Circuit Wiring Diagrams
1997 Isuzu Rodeo Question Fuse Box Diagram Electrical Problem
1999 Isuzu Rodeo Main Fuse Box Diagram Circuit Wiring Diagrams
1998 Trooper Relay Solenoid Starter 1998 Isuzu Trooper All of

Jul 06, 2016 | Isuzu Cars & Trucks

1 Answer

COST OF STARTER REPLACEMENT ON ISUZU RODEO 1998


costs vary by a zillion factors.
country
city.
shop
taxes, rent, labor costs, insurance.
and if the parts are rusty. or related parts are destroy'd.
and if old parts have core value.
why ask here, we know NONE of this,
ask your mech. ask them, in your town.

Jul 14, 2014 | 2003 Isuzu Rodeo

1 Answer

2000 Isuzu Rodeo intermittent starter spins no start


This is very common bad starter, replace the starter and the problem will be solved, some of these isuzu starter are a pain to replace, good day

Dec 25, 2012 | 2000 Isuzu Rodeo

1 Answer

I have a 1999 isuzu rodeo 2WD 3.2L V6. What are the steps in replacing my starter. My car is stranded and i need to try to replace it myself?


The repair manual book says first disconnect the battery , then lift the car to have more space to work on it make sure that is secure if you liftit ,remove the nut to Starter ,also nut to solenoid cable ,or if you think it is easier take off starter first and then after remove nuts to starter and solenoid ,then you ready to install you new or rebuilt starter ,,good luck

Nov 26, 2010 | 1999 Isuzu Rodeo

1 Answer

'93 Isuzu Rodeo, CV Joint replacement.


unbolt the tie rod end and the lower a arm and it should slide out of there

Jan 26, 2010 | 1999 Isuzu Rodeo

1 Answer

How to remove the starter in my 93 isuzu trooper?


I can hook you up!! lol Go to the autozone website at autozone.com and register your vehicle. It's free and you will have access to an online repair manual for your vehicle. The step by step instructions for removing the starter on your vehicle is there. ( I checked). Hope this helped and best wishes.

Jul 30, 2009 | 1993 Isuzu Rodeo

1 Answer

How to remove the starter in my 93 isuzu?


Yes you can do it....just remove the positive lead off of your battery first of all. Those bolts you see is what you have to remove. That should let the starter come down a little so you can take the wires off of the starter. Keep track of where they go so you can put them back on the new starter. When you are done putting the starter in place and tightened all the bolts you can hook the positive wire back to your battery.

Jul 30, 2009 | 1993 Isuzu Rodeo

1 Answer

Car takes 3 times key turn to start. no starter


Sounds to me to be the ignition switch, its going bad.

Jul 07, 2009 | 1993 Isuzu Rodeo

1 Answer

TIMING BELT


broke the timming belt on my 93 isuzu rodeo how do I line everything up for the new belt?

Apr 09, 2009 | 1993 Isuzu Rodeo

Not finding what you are looking for?
1993 Isuzu Rodeo Logo

1,301 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...