Question about 2001 Ford F250 Super Duty Super Cab

1 Answer

Changing water pump. which direction losens the fan nut?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 74 Answers

As far as i know lefty loosey righty tighty hard to say without seeing it good luck. also try calling ford they might be able to help you too if you havent already. best of luck

Posted on Nov 19, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I`m changing the water pump in my 1999 dodge ram 1500, but I can`t lose the fan nut that is attach to the water pump.please help.


Those fan nuts are just tough to get off, however it may have "left-hand" threads. If you can see any threads, look straight down at them...if threads are going "downhill" from right to left, then they are common right-hand threads, Lefty lucy-Righty tighty. However if the threads are going "downhill" from left to right, then they are left-hand threads, and you will need to turn the nut "clockwise" to loosen it. Hope this helps....let me know either way!!

Aug 12, 2011 | 1999 Dodge Ram

1 Answer

How to replace water pump on japanese 1996 bmw 318i


u will have to 1st remove the clutch fan, and losen the belt by turning the tensioner,then remove the fan shroud,this will allow you to remove the fan completely,then once the fan is removed this will allow you ful access to the water pump.at times the pump will be seized onto the engine block so it may require some shaking back and forth.once removed,you can use a thin coat of vascaline to seat the new gasket onto the new pump...good luck.

Aug 04, 2011 | 1996 BMW 318

1 Answer

Need to know how to remove nut on water pump to remove fan/ clutch. have wrenchs


That is about a 36 mm wrench,which is close to
1 7/16".
You will have to borrow one,then use a long pry bar to hold the
nuts on the pulley to pump,so it won't turn

The fan screws on normal direction, as I recall

Mar 06, 2011 | 1996 Dodge Ram 1500 Club Cab

1 Answer

How do you change your water pump, what needs to come off during this process


DRAIN WATER FROM RADIATOR, REMOVE WATER PIPES THEN RADIATOR. LOSEN THE ALTERNATOR BELT AND OTHER BELTS AND REMOVE. LOSEN FAN THEN REMOVE AND THEN YOU HAVE ACESS TO THE WATER PUMP.

Dec 13, 2010 | 2003 Toyota Tacoma

1 Answer

I am trying to remove the fan to replace the water pump, but I can not losen the nut.


try putting wrench on it and smacking it with a mallet,it will come loose may take a few hits

Mar 27, 2010 | 1999 Dodge Ram

2 Answers

Which way do you turn bolt on fan clutch to remove while changing water pump


i do not know but give these websites atry www.alldatadiy.com and www.autozone.com if all fails stop by your local GM-dealership in the parts department and they be able to print you off the pictures and diagrams you will need wish you the best of luck Michigan Man.

Jan 11, 2010 | 2001 Chevrolet Blazer

1 Answer

Remove water pump have removed outer plastic blades of viscous fan and the four small bolts behind the water pump it seems loose but will not come away, is it just the internal impeller blades dont want to...


what's up led, the large viscous nut is loosened in the clockwise direction. after you remove the 4 nuts on the water pump, you should see one hole on each side of the water pump body. if you take 2 bolts out of the thermostat housing, you can use those to thread in the pump body holes.slowly tighten each bolt equally and the pump should come out. to install a new pump, lubricate the o-ring on the new pump and just push in by hand.

Mar 21, 2009 | 1996 BMW 318

1 Answer

Changing the water pump on 2000 Jeep Grand Cherokee V6


WATER PUMP
The water pump is bolted directly to the engine timing chain case/cover.

A gasket is used as a seal between the water pump and timing chain case/cover.

If water pump is replaced because of bearing/shaft damage, or leaking shaft seal, the mechanical cooling fan assembly should also be inspected. Inspect for fatigue cracks, loose blades, or loose rivets that could have resulted from excessive vibration. Replace fan if any of these conditions are found. Also check condition of the thermal viscous fan drive. Refer to Viscous Fan Drive in this group.

The water pump can be removed without discharging the air conditioning system (if equipped)

REMOVAL
Disconnect negative battery cable from battery.
Drain cooling system. Refer to Draining Cooling System in this group.
Do not waste reusable coolant. If solution is clean, drain coolant into a clean container for reuse.

The thermal viscous fan drive is attached (threaded) to the water pump hub shaft. Remove fan/viscous fan drive assembly from water pump by turning mounting nut counterclockwise as viewed from front. Threads on viscous fan drive are RIGHT HAND. Using special tool spanner wrench 6958 with adapter pins 8346 and a suitable fan wrench loosen the fan drive Viscous Fan and Fan Drive Do not attempt to remove fan/viscous fan drive assembly from vehicle at this time.
WARNING: CONSTANT TENSION HOSE CLAMPS ARE USED ON MOST COOLING SYSTEM HOSES. WHEN REMOVING OR INSTALLING, USE ONLY TOOLS DESIGNED FOR SERVICING THIS TYPE OF CLAMP, SUCH AS SPECIAL CLAMP TOOL (NUMBER 6094) SNAP-ON CLAMP TOOL (NUMBER HPC-20) MAY BE USED FOR LARGER CLAMPS. ALWAYS WEAR SAFETY GLASSES WHEN SERVICING CONSTANT TENSION CLAMPS.

CAUTION: A number or letter is stamped into the tongue of constant tension clamps. If replacement is necessary, use only an original equipment clamp with matching number or letter.

If water pump is being replaced, do not unbolt fan blade assembly from thermal viscous fan drive.
Remove two fan shroud-to-radiator nuts Fan Shroud Mounting Hardware Do not attempt to remove fan shroud at this time.
Remove fan shroud and fan blade/viscous fan drive assembly from vehicle as a complete unit.
After removing fan blade/viscous fan drive assembly, do not place thermal viscous fan drive in horizontal position. If stored horizontally, silicone fluid in viscous fan drive could drain into its bearing assembly and contaminate lubricant.
Remove accessory drive belt as follows: The drive belt is equipped with a spring loaded automatic belt tensioner. Relax tension from belt by rotating tensioner clockwise (as viewed from front) Automatic Belt Tensioner - When all belt tension has been relaxed, remove accessory drive belt.
Remove lower radiator hose clamp and remove lower hose at water pump.
Remove seven water pump mounting bolts and one stud bolt
CAUTION: Do not pry water pump at timing chain case/cover. The machined surfaces may be damaged resulting in leaks.

Remove water pump and gasket. Discard gasket.
INSTALLATION
Clean gasket mating surfaces.
Using a new gasket, position water pump and install mounting bolts as shown. Water Pump Installation - Tighten water pump mounting bolts to 54 N·m (40 ft. lbs.) torque.
Spin water pump to be sure that pump impeller does not rub against timing chain case/cover.
Connect radiator lower hose to water pump.
Relax tension from belt tensioner Automatic Belt Tensioner - Install drive belt
CAUTION: When installing the serpentine accessory drive belt, belt must be routed correctly. If not, engine may overheat due to water pump rotating in wrong direction. Refer to Belt Routing for correct belt routing. Or, refer to the Belt Routing Label located in the engine compartment. The correct belt with correct length must be used.

Position fan shroud and fan blade/viscous fan drive assembly to vehicle as a complete unit.
Be sure the upper and lower portions of the fan shroud are firmly connected. All air must flow through the radiator.
Install two fan shroud-to-radiator nuts Fan Shroud Mounting Hardware
Be sure of at least 25 mm (1.0 inches) between tips of fan blades and fan shroud.
Install fan blade/viscous fan drive assembly to water pump shaft.
Fill cooling system. Refer to Refilling the Cooling System in this group.
Connect negative battery cable.
Start and warm the engine. Check for leaks

Jan 10, 2009 | 2000 Jeep Grand Cherokee

1 Answer

Im changeing the water pump on a 199 gmc 3500 and I cat get the cooling fan off. There is a large nut attaches the fan to the water pump that turns everything but wont break free. what is the trick?


You can get the special tools to remove it or some people take a air hammer with a pointed bit and give the edge of the nut a quick hit in the direction the fan spins to break loose the nut.And to tighten it thread it back on half way then start the engine and when it spins it will tighten it up.

Nov 29, 2008 | 1999 GMC Sierra 3500

Not finding what you are looking for?
2001 Ford F250 Super Duty Super Cab Logo

Related Topics:

39 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

fordexpert

Level 3 Expert

5495 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...