Question about 1999 Chevrolet Silverado 1500

1 Answer

Is there a torque spec on the spindle nut for the rear caliper on a 1999 Chevy Silverado 4x4 V8 5.3

Posted by on

  • jeremy_d_dod Nov 19, 2009

    HOw about a torque spec on the spindle nut for the rear rotor?

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chevrolet Master
  • 2,984 Answers

  1. nstall the caliper mounting bolts. Perform the following procedure before installing the caliper guide pin bolts (15 Series only).
  2. Remove all traces of the original adhesive patch.
  • Clean the threads of the bolt with brake parts cleaner or the equivalent and allow to dry.
  • Apply Red Loctite#272 to the threads of the bolt.
  1. Install the caliper mounting bolts (25 series). Tighten the caliper guide pin bolts to 42 Nm (31 ft. lbs.) on the 15 series; 108 Nm (80 ft. lbs.) on the 25 series.

Posted on Nov 19, 2009

Testimonial: "thank you that was very helpful"

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Front wheel bearing replace 4x4


It's pretty simple. -Remove the tire -Install a punch into the fins of the rotor. Rotate the rotor counterclockwise until the punch hits the caliper and remove the axle nut. - I like to remove the outer tie rod end from the knuckle. This makes it easier to get at the caliper bracket bolts and the wheel hub bolts - remove the caliper and the rotor - unplug the abs harness - remove the three bolts that hold the hub to the knuckle. - remove the hub/bearing from the knuckle. The hub may be corroded and frozen a little to the knuckle. Sometimes it can take a bit of hammering to get them to pop. Also make sure you torque the axle nut to the correct torque spec. Failure to do this will causing the bearing to fail early! Let me know if you have any questions and I'll do my best to answer them. Thank you for using FixYa.com!

Feb 25, 2012 | 1999 Chevrolet Silverado 1500

1 Answer

Replace front hub assembly


I don't want to leave you hanging out there but you would be better off buying the repair manual for this repair.
You will have a little more to do if it is 4X4, But the jest of it is, first if it is 4X4, remove the nut that hold the CV axle into the hub, the wheel comes off, brake caliper is unbolted and moved out of the way, then the brake support bracket, then slide the spline of the CV inside the hub, Then remove the four bolts that hold the hub to the spindle. Then reverse for reassembly. Note: The hub may be rusted to the spindle so you may want to try soaking that area with a good penetrating oil.
Remember the repair manual. You will need it for the torque specs. for the hub, the brakes, the lug-nuts, and the nut for the CV.

Apr 27, 2010 | 2004 Chevrolet Silverado 2500HD

1 Answer

Replacing front hub on a 2001 Chevy Silverado 1/2 ton 4 x 4. need to know torque for retaining nut


The torque for the front drive shaft and hub retaining nut is 155ft.lbs. But if you are on the metric system,
it's 210N.m . These specs are for both 1999 and 2001
Hope this helps. Good luck.

Jan 24, 2010 | 1999 Chevrolet Silverado 1500

2 Answers

Front Hub Bearing Torque specs to complete replacement


THE LUG NUT TORQUE SPEC - 140FT/LBS\
CALIPER MOUNT - 80FT/LBS
CALIPER BRACKET 129FT/LBS
AXLE NUT 177FT/LBS

Apr 24, 2009 | 2003 Chevrolet Silverado 1500

1 Answer

2005 chevy 4x42500hd


Hi..
On your 05 Chevy 4X4 2500HD.
The Pinion Yoke Nut, 9.75" Axle. the torq spec. is 370 Nm. -- 273 Lb ft.

I hope this help on your question.

Thank you for use fixya...

Nov 04, 2008 | 2008 Chevrolet Silverado 2500HD 2WD

Not finding what you are looking for?
1999 Chevrolet Silverado 1500 Logo

426 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8152 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...