Question about 2000 Chrysler Sebring

1 Answer

2000 sebring conv. I am trying to replace the input speed sensor and I cannot figure out how to get to it. I know where it is (I think) but its too hard to get to. Any advice?

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 65 Answers

If you are talking about the sensor for the speedometer, the only way I know to access it is from underneath the car. Be sure to disconnect the electrical connector first with a flat blade screw driver to lift the retaining tab. Then take your box end wrench, feel for the bolt head and remove it.

Posted on Nov 19, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 2000 Mazda 626 LX 2.5 L automatic transmission with the code p0715. Any help?


no
a vehicle speed sensor ( VSS) reports on the vehicle speed to the ECM, speedo and TCM
the turbine speed sensor reports on the input shaft speed so that the TCM knows when to change ratios against the VSS reports
the sensor is readily available from dealer spares , transmission shops , e-bay or the wreckers / junk yards
talk with an accredited transmission specialist shop

Jul 07, 2017 | Mazda Cars & Trucks

1 Answer

Car shuts off while driving now won't start check engine light came on while driving


check code probable p0340 camshaft position sensor. I have the same problem on 2005 sebring sedan. I was told to check the circuit at the crankshaft and camshaft sensors for the proper voltage. I'm still trying to figure mine out. If you find your answer, let me know.

Nov 21, 2010 | 2005 Chrysler Sebring Conv

1 Answer

2005 Chrysler Sebring - engine stumbles and won't excel. and has the engine codes P0016, P0300, P0339


I wasn't able to find out the first engine code, but the other one is a multiple or random misfire. and crankshaft position sensor a circuit. If the car has a distributor you could tried replacing the cap rotor and also wires first. Next you would look at the crankshaft position sensor try unplugging and plugging it back in. Look at the connection and wires to make sure they look OK. If you do not know how to test this you could also just replace the sensor. Good luck.

Jun 25, 2010 | 2005 Chrysler Sebring Conv

1 Answer

Where is the crankshaft position sensor located on a 2000 Sebring Conv.


removal steps (CPS) -remove air intake hose -Battery tray -Crankshaft position sensor

Apr 27, 2010 | 2000 Chrysler Sebring

1 Answer

2008 sebring convertivble -m wont shift


if was running fine and and next day just wont go y woulthink is probably oyu input or output speed sensor,oyu need to check it with scanner and see if is that is the problem and not you tranny brain

Sep 27, 2009 | 2008 Chrysler Sebring Convertible

1 Answer

2000 chrysler sebring conv


this is the diagnostic procedure for your problem. (this is actually from a 3.0L engine but the procedure is exactly the same for the 2.5L)

click for full size
3f6ba68.jpg
2627050.jpg

5e54c06.jpg

Jan 20, 2009 | 2000 Chrysler Sebring

1 Answer

Throttle position sensor


its located on the opposite side of the throttle body as the throttle cable. remove the whole throttle body then remove the TPS from it.

Jan 15, 2009 | 2000 Chrysler Sebring

1 Answer

Ecm


you need the new controller initialized from the dealer or a garage that has a DRB.

Jan 10, 2009 | 2000 Chrysler Sebring

Not finding what you are looking for?
2000 Chrysler Sebring Logo

133 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8518 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...