Question about 2001 Hyundai Accent

1 Answer

Need pin-out for 2001 hyundai accent o2 sensor on exhaust. wirers pulled out from connector their are two white one black and one grey

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

For $29.99 I will tell you. bite me

Posted on Nov 20, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2001 Hyundai Accent Output shaft speed sensor


output shaft speed sensor on top transmission. just depress the release tab disconnect electrical connector then remove output shaft sensor bolt.remove sensor.

Jul 15, 2013 | 2001 Hyundai Accent

2 Answers

2001 Cadillac Deville oxygen sensor wiring diagram


The wiring diagram shows the wiring color code, Power rating and connector plug used. The wiring diagram explains the vehicle's electrical connections with color code. It's a bit complicated to understand.

6d70bec4-a83f-4733-a114-8a73592152a7.jpg

Apr 07, 2013 | 2001 Cadillac DeVille

1 Answer

O2 sensor wire connections.my original o2 sensor adaptor got melted by my exaust,so it was cut off the original wiring harness which had 4 wires which are red/white, orange,grey/white and grey. But the...


Ford Explorer is equipped with two oxygen sensor positioned on the exhaust manifold. Its necessary to replace the oxygen sensor at the first sign of failure. You can get all necessary details about o2 sensor at http://www.wholesalesensors.com/ford-oxygen-sensor/

Jun 23, 2011 | 2003 Ford Explorer

1 Answer

Where are the o2 sensors on 1999 hyundai accent


the lambda probe is situated between the exhaust manifold and the FIRST box on the exhaust system.looks like a pen cap with a couple of wires hanging off.

Apr 03, 2011 | 1999 Hyundai Accent

1 Answer

My 2001 hyundai accent has suddenly started to stall itself it can be running then just all of a sudden stall but it also can do this while driving along but would kick back in again while driving but its...


i think you need to go back to basics.if here is no obd fault codes in the system to give you a clue. then use a multimeter and have a good look at the wiring for corroded connectors etc. including the fuel pump?

Oct 13, 2017 | 2001 Hyundai Accent

1 Answer

I need to know which wire on the 4 wire oxygen sensor (2 white, one grey one black) is the heat wire on a ford f-150 o2 sensor?


Hello! There are four O2's...Each O2 heater, left and right bank, front and rear, has it's own wire colors...These colors are "at the connector"...First series are the control ground sent by the PCM..
RR=White/Black...RF=Red/White...LR=Tan/Yellow...And LF=Yellow/Light Blue...........This series are the battery leads, hot when fuel pump relay pulls...RR=Violet/White...
RF=Red/Yellow...LR=Violet/White...LF=Red/Yellow...

If you have any questions feel free to ask...Guru...Saailer

Oct 20, 2010 | 2001 Ford F150 Styleside SuperCrew

1 Answer

Where are the front and rear O2 sensors?


The manifold and under below the engine on the exhaust pipe

Mar 06, 2010 | 2000 Hyundai Accent

1 Answer

How do you replace the oxygen sensors in a 2001 nissan altima?


REMOVAL & INSTALLATION
  1. Start the engine and allow it to reach normal operating temperature, then turn the ignition switch OFF.
  2. Disconnect the negative battery cable.
  3. Open the hood and locate the Oxygen (O2S) sensor connector. It may be necessary to raise and safely support the vehicle for access to the sensor and its connector. NOTE: On a few models, it may be necessary to remove the passenger seat and lift the carpeting in order to access the connector for a downstream O2S sensor.
  4. Disengage the O2S sensor pigtail connector from the vehicle harness connector. NOTE: There are generally 2 methods used to mount an O2S sensor in the exhaust system: either the O2S sensor is threaded directly into the exhaust component (screw-in type) or the O2S sensor is retained by a flange and 2 nuts or bolts (flange type). WARNING
    To prevent damaging a screw-in type O2S sensor, if excessive force is needed to remove the sensor lubricate it with penetrating oil prior to removal. Also, be sure to protect the tip of the sensor. O2S sensor tips are very sensitive and may be easily damaged if allowed to strike or come in contact with other objects.
  5. Remove the sensor, as follows:
    • Screw-in type sensors — O2S sensors are usually designed with a permanently attached wiring pigtail. This allows the wiring harness and sensor connectors to be positioned away from the hot exhaust system. It may be necessary to use a socket or wrench that is designed specifically for this purpose. Before purchasing such a socket, be sure that you can't save some money by using a box end wrench for sensor removal.
    • Flange type sensors — Loosen the hold-down nuts or bolts and pull the sensor out of the exhaust component. Be sure to remove and discard the old sensor gasket, if equipped. You will need a new gasket for installation.
  6. Perform a visual inspection of the sensor. Black sooty deposits may indicate a rich air/fuel mixture, brown deposits may indicate an oil consumption problem, and white gritty deposits may indicate an internal coolant leak. All of these conditions can destroy a new sensor if not corrected before installation. To install:
  7. Install the sensor, as follows: NOTE: A special anti-seize compound is used on most screw-in type O2S sensor threads, and is designed to ease O2S sensor removal. New sensors usually have the compound already applied to the threads. However, if installing the old O2S sensor or the new sensor did not come with compound, apply a thin coating of electrically-conductive anti-seize compound to the sensor threads. WARNING
    Be sure to prevent any of the anti-seize compound from coming in contact with the O2S sensor tip. Also, take precautions to protect the sensor tip from physical damage during installation.
    • Screw-in type sensors — Install the sensor in the mounting boss, then tighten it securely.
    • Flange type sensors — Position a new sensor gasket on the exhaust component and insert the sensor. Tighten the hold-down fasteners securely and evenly.
  8. Reattach the sensor pigtail connector to the vehicle harness connector.
  9. Lower the vehicle.
  10. Connect the negative battery cable.
  11. Start the engine and ensure no Diagnostic Trouble Codes (DTC's) are set.

Fig. 1: Since sensor locations vary between vehicles, the first step in removal is to locate the O2S sensors (arrows)...

bb4d603.jpg
    Fig. 2: ... and the sensor connector (2), which is usually near the O2S sensor (1), but removed enough from the heat of the exhaust system
    5048c2d.jpg
    Fig. 3: Disengage the sensor pigtail connector half from the vehicle harness connector half
    a1433b0.jpg

Oct 01, 2009 | 2001 Nissan Altima

1 Answer

Location of sensors


IAT SENSOR IS MOUNTED INSIDE INTAKE AIR HOSE TO THE AIR CLEANER ASSEMBLY. THE MASS AIR FLOW SENSOR IS ALSO MOUNTED TO THE INTAKE AIR HOSE OF THE AIR CLEANER ASSEMBLY. O2 SENSORS LOCATION.YOU HAVE 2 # O2 SENSORS.YOU HAVE ONE THE EXHAUST MANIFOLD.THE OTHER SENSOR LOCATED DOWN AT THE CATALYTIC CONVERTER.

Aug 19, 2009 | Hyundai Accent Cars & Trucks

1 Answer

What the heck does a P2096 DTC mean on a 2004 Hyundai Accent?


P2096 - Post Catalyst Fuel Trim System Low Limit.

Possible Causes
EXHAUST LEAK
ENGINE MECHANICAL PROBLEM
1/2 O2 SENSOR2.gif
(K141) O2 SENSOR 1/2 SIGNAL CIRCUIT
(K299) O2 1/2 HEATER CONTROL CIRCUIT
(K904) O2 DOWNSTREAM RETURN CIRCUIT
FUEL CONTAMINATION

Jul 26, 2009 | Hyundai Motor 2004 Accent

Not finding what you are looking for?
2001 Hyundai Accent Logo

Related Topics:

131 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

79865 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8836 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...