Question about 1998 Chevrolet Malibu

1 Answer

I have a 1998 chevy malibu what wire for the o2 sensor is the signal wire and theres four to choose from

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Master
  • 4,803 Answers

On the front O2 Sensor, the signal wire s Purple. On the rear O2 Sensor, the signal wire is Purple and White. (You will probably have to look at the wire colors on the main harness side of the O2 Sensor connector, not on the sensor itself.)

Posted on Nov 19, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

I have 2002 chevy impala changed the 02 sensor and it is still reading the same 02 sensor.

because its not the sensor.
its the plug for the sensor .the wires.or it
is the cataletic converter/exhaust system
i just replaced my exhaust on my 07 chevy malibu same o2 sensor issue p0420 or something like that ?!
replace the converter and youll be fine i still have my old sensors in there that gave me the code :)
there not saying there bad but that the cat is bad.

Mar 18, 2015 | 2002 Chevrolet Impala

1 Answer

1998 ford 5.4 o2 sensor 2 scan tool readings only 30 and no fluctuation. What do I look for?

Try changing o2 sensor Should be between .100 and .900 volt and very quick changing. if defective ecu give him a fix prevalue.His it a one,two or four wire o2 sensor if it is four it is a HTO2 (heated o2 sensor must have 12 volt ign on too)

May 04, 2014 | 1998 Ford Expedition

1 Answer

How do you delete code p1137 from 2001 Chevy cavalier ?

Four digit codes are brand specific. Code 1137 for a GM product means the O2 sensor mounted after the catalytic converter is producing a low signal.
The sensor and wiring would need to be checked.

Jun 23, 2013 | Cars & Trucks

1 Answer

P0136 for a 1998 malibu

o2 sensor circuit malfunction bank 1 sensor 2 need to check the o2 sensor located after the cat converter on exhaust pipe need to check wiring and sensor for damage ,corrosion or disconnection repair or replace as needed

Mar 31, 2013 | 1998 Chevrolet Malibu

1 Answer

Where is the front o2 sensors located on a 1998 chevy malibu?

closest to the engine.rear exhaust manifold on the exhaust manifold 4 cyl.

Dec 02, 2010 | 1998 Chevrolet Malibu

1 Answer

Where is the crank positioning sensor located on a 98 chevy malibu 4 cylinder

if a 2.2 four-cylinder, remove the starter motor. disconnect the 7x crankshaft position wiring and harness connector. remove crankshaft retaining bolt and withdraw sensor from engine block. replace the "O" ring and lightly lubricate it with new engine oil. installation is reverse of removal. have a good one !!

Oct 24, 2010 | 1998 Chevrolet Malibu

1 Answer

Lower O2 sensor on a '98 Civic EX coupe.

it might be easier picking up a plug at a salvage yard then just connect to the correct colors,if you have four wires two should be black and two white,

Nov 24, 2009 | 1998 Honda Civic

1 Answer

I took my 1997 chevy malibu to get an emissions test. It failed because the evaporative system monitor was not ready. But a DTC code was found the code that was found was P0141 wich when i looked it up...

I would replace the sensor due to the fact that a P0141 is a malfunction in the heater circuit of the Bank 1 Sensor 2 O2 sensor. There is always a slight chance that there is a short in the wiring harness though. But I would look at the sensor and the harness and if the wiring seems to be in tact, then I would go ahead and replace the sensor.

Jun 29, 2009 | 1997 Chevrolet Malibu

2 Answers

Bad knock sensor on 1998 chevy malibu 2.4L

The knock sensor is on the back side of the engine near the trans. It is round, with a 1 wire connector. You will have to get it from underneath. Good Luck.

May 06, 2009 | 2008 Infiniti FX35

1 Answer

O2 sensor

The return signal is pin A circuit number 413 which is a tan wire.

Aug 11, 2008 | 1998 Chevrolet Malibu

Not finding what you are looking for?
1998 Chevrolet Malibu Logo

Related Topics:

220 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts


Level 3 Expert

76673 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8531 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides