Question about 1983 Jeep CJ7

1 Answer

I need to know how to remove the dash pad on a 1980 Jeep CJ7 so I can then remove the upper defrost duct.

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 47 Answers

There are four or five screws you have to fold the windshield down to get. Then there are usually two or three from the front going into the dash. You'll probably have to take the dash off too to get the defroster duct out.

Posted on Jan 26, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the blower resister on the 2011 sorento? I found the blower behind the glove box but don't know which one is the resister?


If you are referring to the "heater" blower motor resister?
It is under the top section of the dashboard where the shelf detent pad is. First remove the screws on top of the pad area, next start lifting up the right side of the dashboard section towards the center and over towards the left over the instrument cluster and lift out the complete top of the dash. Next remove the defroster duct by removing the screws. Unclip from the lower section and the duct will lift out. The resister is located there under the dash area and will unbolt allowing removal. "Good Luck."

Apr 11, 2017 | Cars & Trucks

2 Answers

My blower speeds stoped working only have full blast or nothing.


Sounds like your blower motor resistor is bad. The resistor allows different speeds of the fan other that full 12 volts (which is the high speed). The resistor is located on the passenger side on the heating housing assembly behind the glove box (kind of). It somewhat difficult to get to.

Here is a youtube video of someone working on one. I don't know what model car you have, so take the video as a "generic" repair and it may be a little different on your car.

www.youtube.com/watch?v=yLDnlQ6cAw0

Apr 25, 2011 | Saturn SL1 Cars & Trucks

1 Answer

1995 jeep grand cherokee tach light is burned out. The rest work fine. How do I fix it?


you must remove the cluster heres some diagrams to help you. hope this helps, dissconnect battery,then remove ash tray,remove center bezel screws,remove bezel,now remove screws for holdingdash pad behind top of center bezel, pry defrost grill out of dash unplug sensors and set aside,remove screws holding dash pad to defrorst duct and cluster,open glovebox and remove screws holding pad, remove pad,pop out has clips holding,remove screws from cluster pull cluster up and out enough to unhook connector. heres some diagram to help.ab9f0ee.gif0b7cf5b.gif1ddb17d.gif

Feb 11, 2010 | 1995 Jeep Grand Cherokee

1 Answer

'94 Camry windshied defroster gets no air flow. When switch is moved,it doesn't change airflow-always comes out ot the ducts facing the passenger area(top ducts)only.


The problem concerning the no air flow out the defrost duct on my mom's 94 Toyota Camry is that the rod link from the electric actuator to the vent / defrost flap became disconnected way up under the center left side under the dash. I had to remove the lower air duct from under the steering column for access to use a 1 inch hole saw to make an access hole on the upper side of the case tube opening to see where the rod came off the lever. I went to the local Toyota dealer to try to buy a retainer clip but the part guy told me that it was only sold as a complete housing piece which was very expensive and involved removing a big portion of the dash pad assembly to replace the housing.
At this point , I plan on reconnecting the rod to the lever by simply installing a special washer style retainer on to the end of the rod to keep it connected. You might find a retainer like this one in a carberator repair kit.

Feb 06, 2010 | 2008 Toyota Camry

1 Answer

93 sts upper dashpad removal


remove the vents with a flat head screw driver. use a 7mm socket to remove 1 bolt each vent . now thair are 3 screwes in the defrost vent remove them. remove the trim that covers the matal wher the windshild is thay just pop off it goes from the dash pad to the headliner u should know what im talking about. now be carfule and remove the sensor where the defrost cover is . and thats it

Jan 20, 2010 | 1994 Cadillac Seville

1 Answer

1984 Jeep CJ7 heater core leaking. '93 inline 6 motor. Wrangler dash. How to I remove the core?


  1. Disconnect battery ground cable and drain cooling system.
  2. Disconnect heater core hoses.
  3. Disconnect damper door control cables.
  4. Disconnect blower motor electrical connector.
  5. Disconnect water drain hose and defroster hose.
  6. Remove nuts retaining heater housing assembly to instrument panel. Remove heater housing assembly by tilting heater downward to disengage it from air inlet duct and pulling toward rear of vehicle.
  7. Remove heater core from heater housing.
  8. Reverse procedure to install.

Nov 17, 2009 | 1984 Jeep CJ7

1 Answer

Vacuum diagram for 1980 cj7 jeep 2.5 motor


You can use any vacuum port on the manifold for that. If you want to mess with it a bit, if you have an open port on the carb that is above the throttle plate, you can use that and see if performance is better. Some engines like it and some don't, but it's not like you have to take the engine apart to try it!!

Oct 08, 2009 | Jeep CJ7 Cars & Trucks

1 Answer

I hear a high pitched scraping sound when I press down on my brakes to come to a stop. I need to know if that means the brakes need to be replaced and if so how do I do that? I've done a brake pad...


No it won't, but it should be easier. The 70's CJ7 was a hub and rotor assembly. The Honda is just a disc rotor. Remove the wheel, caliper and bracket and then the rotor should just come off. Reverse the way you took it apart and fit in the new pads after pressing the caliper piston back in.

Aug 04, 2009 | 1998 Honda Civic

1 Answer

Why does my cj7 choke out in water


get a snorkel if intake is submerged under water

Jan 17, 2009 | 1985 Jeep CJ7

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

192 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...