Question about Ford Five Hundred

3 Answers

I HAVE A 2006 FORD 500. DRIVING ON INTERSTATE WITH CRUISE ON. WENT TO PASS A CAR AND IT DECELERATED. WILL ONLY GO ABOUT 5 MPH

Posted by on

  • dmartin069 Nov 19, 2009

    FUEL PRESSURE WHILE ITS RUNNING IS 28 LBS AND IM NOT GETTING ANY CODES

  • dmartin069 Nov 19, 2009

    IM ONLY GETTING 28 LBS OF FUEL PRESSURE WITH THE CAR RUNNING. IT WILL IDLE FINE BUT NO ACCELERATION

×

3 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 10,515 Answers

Hi,

You could have a bad mass air flow sensor. Or the snorkel from the mass air flow sensor to the throttle body could be ripped. Both are very common and can cause you vehicle to loose power along with many other drive ability issues. First look for cracks or rips or anywhere air can enter the engine that is not accounted for by the mass air flow sensor. Next comes the Mass Air Flow (MAF) sensor. This is a very important sensor input to the computer. It uses a hot wire sensing element to measure the amount of air entering the engine. The MAF sensor then outputs an analog voltage signal to the PCM proportional to the intake air mass. The PCM calculates the required fuel injector pulse width in order to provide the desired air/fuel ratio. If the sensor is bad than this air/fuel ratio will be off causing severe performance issues. In extreme cases, I have seen these two problems cause a no start condition. This input can also be used in determining transmission Electronic Pressure Control, shift and torque converter clutch scheduling. The check engine light may even pop on if the sensor is bad, the snorkel is ripped or a tube has fallen off. This will result in a lean condition.

Let me know, if needed further assistance.

Hope i helped you.

Thanks for using ' Fixya ' and have a nice day!!

Posted on Nov 19, 2009

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 17,970 Answers

I think that the new Ford vehicles included Adaptive Cruise Control, exaclty I dont know how to work, but the driver set this parameters.

Adaptive Cruise Control (ACC) improves on traditional cruise control by allowing a vehicle to automatically adapt to the speed of highway traffic. follow another vehicle at a set distance. With ACC, the driver selects a desired interval to follow traffic as well as the desired cruise speed. When slower traffic is encountered the ACC alters vehicle speed to maintain the desired interval while following traffic. Speed is controlled by ACC with moderate braking when needed. When traffic clears, ACC resumes the desired cruise speed. The driver may override the system by braking at any time.

How it works: When activated by the driver, a microwave radar unit or laser transceiver on the front of the vehicle determines the distance and relative speed of any vehicle which may be in the path of travel. The ACC computer continually commands the throttle and brakes to maintain cruise speed or adapted speed of traffic. Braking by the driver can override the system at any time.

I suggest review the owners manual for details about Cruise Control.

Hope helped.

Posted on Nov 19, 2009

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,615 Answers

Most likely what happened was a fault was detected and a code was stored and then the PCM went into limp mode for safety factors. As long as the code is stored the car will not clear it on a restart. Only option is to get a code reader and clear all memory codes to see if it returns to normal. Only other option is for the dealer to check it out . You will need Ford specific diagnostic equipment to access all the test that are possible

Posted on Nov 19, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is the drive cycle for a 2003 Nissan Sentra SE?


Take extra caution while performing dirve cycles on public roadways. Drive cycles can be difficult to follow under normal driving conditions. Begin by: - Start the engine. Idle the engine in drive for two and a half minutes with the A/C and rear defroster on. - Turn the A/C and rear defrost off, and accelerate to 55 mph at half throttle. - Hold at a steady speed of 55 mph for three minutes. - Decelerate (coast down) to 20 mph without braking or depressing the clutch. - Accelerate back to 55 to 60 mph at ¾ throttle. - Hold at a steady speed of 55 to 60 mph for five minutes. - Decelerate (coast down) to a stop without braking. If all other emissions systems are functioning properly, completing the drive cycle above will set the "readiness flags" required to pass the smog check. It will not hurt to perform the drive cycle 2 or 3 times before the smog test.

Oct 06, 2016 | 2003 Nissan Sentra

1 Answer

How do i set the cruise control on my 1994 mercedes c220 elegance automatic


Cruise Control
Any given speed above approximately 22 mph (35 km/h) can be maintained with the cruise control by operating the lever.
-see photo

  1. Accelerate and set: Lift lever briefly to set speed. Hold lever up to accelerate.
  2. Decelerate and set:
    Depress lever briefly to set speed. Hold lever down to decelerate.
    Normally the vehicle is accelerated to the desired speed with the accelerator. Speed is set by briefly pushing
    the lever to position 1 or 2. The accelerator can be released. The speed can be increased (e.g. for passing)
    by using the accelerator. As soon as the accelerator is released, the previously set speed will be resumed automatically. If a set speed is to be increased or decreased slightly, e.g. to adapt to the traffic flow, hold lever in position 1 or 2 until the desired speed is reached, or briefly tip the control lever in the appropriate direction for increases or decreases in 0.6 mph (1 km/h) increments. When the lever is released, the newly set speed remains.
  3. Canceling
To cancel the cruise control, briefly push lever to position 3.
When you step on the brake or the vehicle speed drops below approx. 22 rnph (35 km/h), for example when driving upgrade, the cruise control will be canceled.
4. Resume
If the lever is briefly pushed to position 4 when driving at a speed exceeding approx. 22 mph (35 km/h), the vehicle resumes the speed which was set prior to the cancellation of the cruise control. The last memorized speed is canceled when the key in the steering lock is turned to position 1 or 0.
Note:
If the engine does not brake the vehicle sufficiently while driving on a downgrade, the speed you set on the cruise control may be exceeded and you may have to step on the brake pedal to slow down.
As soon as the grade eases, the cruise controlled speed will again be maintained as long as the brakes were not previously applied, or the lever may be used to resume the previously set speed if the brakes were applied.

set-cruise-control-1994-mercedes-c220-sufrpujyrsap3pvz3w2boz5j-3-0.jpg
http://www.benzworld.org/forums/attachments/w202-c36-c43/153145d1197313761-pdf-owners-manual-w202-1995-2000-1999-c280_owners_manual.pdf

Feb 14, 2015 | Mercedes-Benz C-Class Cars & Trucks

1 Answer

How to get Drive cycle



1. The testing has to start with the vehicle under 122 degrees F. Start the engine and idle for 2.5 minutes in Drive (auto) Neutral (MAN) A/C and rear defogger ON.

2. A/C OFF, accelerate to 55 MPH at 1/2 throttle and then 3 minutes of steady state cruise at 55 MPH.

3. Clutch engaged (MAN) no braking decelerate to 20 MPH.

4. Accelerate to 55-60 MPH at 3/4 throttle and 5 minutes of steady state cruise at 55-60 MPH.

5. Decelerate, no braking to end the drive cycle.

In some cases the Powertrain Control Module (PCM) will go into a logic lock not letting the readiness monitors run. Removing the battery cables and touching the two together will normally take care of the logic lock condition.

Apr 26, 2014 | 1999 Buick Park Avenue

1 Answer

Why is mybcm not letting me pass insp there is no code on thi1996 chry lhs what is going on


You mean PCM most states read the readiness monitors depending on the state on how many they allow not to be completed. The first one on the list that is hard to get run and pass is the EVAP Because this requires the car to be cold and fuel tank must between 15%-85% and both air temp and coolant temp with in 10 degrees of each other. Start car let idle for 5 -10 minutes Then drive car normally no hard accelerations or quick stops bring speed to 50-60 mph and coast down to 20-15 mph without brake pedal input repeat this twice.Then bring speed to 58-62 mph and set cruise control run for 12-16 miles exit freeway caught a red light or stop and idle 2 minutes shut car off rest for 5 minutes and repeat freeway drive. then redo morning cold start again . then have some one test the generic readiness monitors to what needs to run and attempt again. California before 2000 1 can be incomplete after 2000 all have to be completed which is hard some will not run for 800 miles.

Nov 08, 2013 | 2001 Ford Escape

1 Answer

Drive cycle


Here is the OBD2 emission system drive cycle test procedure.
Engine coolant temp must be below 70c (158f) before starting the engine for either the first or second trip
The fuel level should be less than 1/2 full
First trip:
Start engine, idle for at least 1.5 minutes
Drive 3 minutes, hold b/f schdl: 1.5-2.0 msec, selector lever "3rd" eng rpm 1,800-2,000 A/C switch:ON Hold the recommended b/f schdl range. Allow road speed to vary as necessary.
Drive at 55-65 mph for 1.5 min b/f schdl 2.0-3.2 msec, selector lever "5th" Engine rpm 2,200-3,000
IGN "off" for at least 10 seconds (not more than 5 min)
Dive at 50-60 mph for 3 minutes Selector lever "4th" keep engine speed above 3,000 rpm Allow speed to vary if necessary. Do not decelerate for more than 3 consecutive seconds. A/C switch ON.
Drive at a steady state cruise of 53-58mhp b/f schdl more than 1.8 msec selector lever "5th" eng rpm 2,400-2,600
Downshift to "4th" and decel more than 5 seconds without breaking, then idle for 1 minute.
Drive two minutes b/f schdl less than 2.0 msec Accelerate to 41 mph, decelerate to 34 mph, accelerate to 41mph. Do not completely release the accelerator. A/C switch off.
Idle 1 minute in park or neutral
Drive two minutes Steady state cruise at 31-44 mph. Selector lever "4th" A/C switch OFF. Hold the accelerator pedal as steady as possible. Allow speed to change if necessary.
End of first trip. Turn the key off the begin the second trip.
Second trip:
Start engine, idle for at least 1.5 minutes
Drive 3 minutes, hold b/f schdl: 1.5-2.0 msec, selector lever "3rd" eng rpm 1,800-2,000 A/C switch:ON Hold the recommended b/f schdl range. Allow road speed to vary as necessary.
Drive at 55-65 mph for 1.5 min b/f schdl 2.0-3.2 msec, selector lever "5th" Engine rpm 2,200-3,000
IGN "off" add four gallons of fuel
Dive at 50-60 mph for 3 minutes Selector lever "4th" keep engine speed above 3,000 rpm Allow speed to vary if necessary. Do not decelerate for more than 3 consecutive seconds. A/C switch ON.
Drive at a steady state cruise of 53-58mhp b/f schdl more than 1.8 msec selector lever "5th" eng rpm 2,400-2,600
Downshift to "4th" and decel more than 5 seconds without breaking, then idle for 1 minute.
Drive two minutes b/f schdl less than 2.0 msec Accelerate to 41 mph, decelerate to 34 mph, accelerate to 41mph. Do not completely release the accelerator. A/C switch off.
Idle 1 minute in park or neutral
Drive two minutes Steady state cruise at 31-44 mph. Selector lever "4th" A/C switch OFF. Hold the accelerator pedal as steady as possible. Allow speed to change if necessary. I especially like the part where they want you to add four gallons of fuel. Not three gallons, not five gallons, four gallons. Gotta love those Nissan engineers. ...and of course they state that if the trace is not followed exactly (i.e. you botch the acceleration/deceleration) you have to start all over again from scratch

Feb 09, 2012 | 1996 Nissan Pickup

1 Answer

Obd2 system rediness status won't clear so I can run the smog test due to replacing the battery.


takes a long time to run the rediness test since there are 6 different tests to complete...

PROCEDURE 1
EVAPORATIVE EMISSION SYSTEM LEAK MONITOR
Inspection Conditions
Engine coolant temperature: 30°C (75°F) or less (The engine is stopped before the test drive is started).
Atmospheric temperature: 5 - 30°C (41 - 113°F).
Condition of A/T: Selector lever D range.
Fuel remained in fuel tank: 30 - 50% is recommended.
Time required: 16 minutes or less after started the engine.
Drive cycle pattern: One trip monitor (from start to ignition switch to "LOCK" (OFF) position. Well be completed while traveling with the following drive cycle pattern.
Test Procedure
Engine: start.
Accelerate until the vehicle speed is 89 km/h (55 mph) or more.
While keeping the accelerator pedal opening degree constant, keep the vehicle speed at 89 km/h (55 mph) or more and travel for 16 minutes.
Return the vehicle to the shop, then turn the ignition switch to "LOCK" (OFF) position.

PROCEDURE 2
FUEL TRIM MONITOR
Drive Cycle Pattern
Inspection Conditions
Engine coolant temperature: 100°C (212°F) or less.
Atmospheric temperature: -10 - 60°C (14 - 140°F).
Condition of A/T: Selector lever D range.
Time required: 30 minutes or more.
Drive cycle pattern: One trip monitor (from start to ignition switch to "LOCK" (OFF) position). Will be completed while traveling with the following drive cycle pattern.
Test Procedure
Engine: start.
Accelerate until the vehicle speed is 89 km/h (55 mph) or more.
While keeping the accelerator pedal opening degree constant, keep the vehicle speed at 89 km/h (55 mph) or more and travel for 30 minutes.
Return the vehicle to the shop, then turn the ignition switch to "LOCK" (OFF) position

PROCEDURE 3
CATALYTIC CONVERTER MONITOR
Drive Cycle Pattern
Inspection Conditions
Atmospheric temperature: -10°C (14°F) or more.
Condition of A/T: Selector lever D range.
Engine coolant temperature: Not set.
Time required: 16 minutes or more.
Drive cycle pattern: One trip monitor (from start to ignition switch to "LOCK" (OFF) position). Will be completed while traveling with the following drive cycle pattern.
Test Procedure
Engine: start.
Accelerate until the vehicle speed is 89 km/h (55 mph) or more.
Travel for 300 seconds or more while keeping the vehicle speed at 89 km/h (55 mph) or more.
Decelerate until the vehicle speed is within 80 km/h (50 mph) or less.
While traveling at 56 - 80 km/h (35 - 50 mph) for 10 minutes or more, fully close the throttle at least once in 2 minutes and decelerate for 10 seconds or more.
Do not repeat deceleration too often.
Vehicle speed may go below 56 km/h (35 mph) after the deceleration.
Stopping and braking are permitted. (If stopped or drive at 56 km/h (35 mph) or less for more than 5 minutes the monitoring may be stopped. In this case please restart monitoring from the beginning.)
After completing the above deceleration, bring the vehicle speed back to 56 - 80 km/h (35 - 50 mph) and keep it in the range until starting the deceleration again.
Repeat the above deceleration at least 5 times.
Return the vehicle to the shop, then turn the ignition switch to "LOCK" (OFF) position

PROCEDURE 4
HEATED OXYGEN SENSOR MONITOR
Drive Cycle Pattern
Inspection Conditions
Engine coolant temperature: 100°C (212°F) or more.
Atmospheric temperature: -10°C - 60°C (14 - 140°F) or more.
Condition of A/T: Selector lever D range.
Time required: 16 minutes or more.
Drive cycle pattern: One trip monitor (from start to ignition switch to "LOCK" (OFF) position). Will be completed while traveling with the following drive cycle pattern.
Test Procedure
Engine: start.
Accelerate until the vehicle speed is 56 - 80 km/h (35 - 50 mph).
While keeping the accelerator pedal opening degree constant, keep the vehicle speed at 56 - 80 km/h (35 - 50 mph) and travel for 16 minutes or more.
Stopping and braking during this operation are permitted. Keep the accelerator opening degree constant for 1 minute or more after each acceleration.
Return the vehicle to the shop, then turn the ignition switch to "LOCK" (OFF) position

PROCEDURE 5
EXHAUST GAS RECIRCULATION (EGR) SYSTEM MONITOR
Drive Cycle Pattern
Inspection Conditions
Engine coolant temperature: 100°C (212°F) or less.
Atmospheric temperature: 5 - 60°C (41 - 140°F).
A/C switch: OFF.
Condition of A/T: Selector lever D range.
Time required: 16 minutes or more.
Drive cycle pattern: One trip monitor (from start to ignition switch to "LOCK" (OFF) position). Will be completed while traveling with the following drive cycle pattern.
Test Procedure
Engine: start.
Accelerate until the vehicle speed is 56 - 80 km/h (35 - 50 mph).
While traveling 16 minutes or more at 56 - 80 km/h (35 - 50 mph) with engine speed 2,000 r/min or above, fully close the throttle at decelerate for 5 seconds or more until the engine speed reaches 1,000 r/min or under.
Do not repeat deceleration too often.
Stopping and braking are permitted (Rapid deceleration and sharp steering are not permitted).
After completing the deceleration, bring the vehicle speed back to 56 - 80 km/h (35 - 50 mph) and keep it in the range until starting the deceleration again.
Repeat the above deceleration at least 8 times by fully closing the throttle valve.
Return the vehicle to the shop, then turn the ignition switch to "LOCK" (OFF) position

PROCEDURE 6
OTHER MONITOR (Main Components, Sensors & Switches, Wire Breakage & Short Circuit)
Drive Cycle Pattern
Inspection Conditions
Engine coolant temperature:
100°C (212°F) or less (Except engine coolant temperature sensor monitoring).
30°C (86°F) or less (Engine coolant temperature sensor monitoring).
Atmospheric temperature:
5°C (41°F) or more (Except engine coolant temperature sensor monitoring).
-10°C (14°F) or less (Engine coolant temperature sensor monitoring).
Condition of A/T: Selector lever D range.
Time required: 21 minutes or more.
Drive cycle pattern: One trip monitor (from start to ignition switch to "LOCK" (OFF) position). Will be completed while traveling with the following drive cycle pattern.
Test Procedure
Engine: start
Accelerate until the vehicle speed is 56 km/h (35 mph) or more.
While keeping the accelerator pedal opening degree constant, keep the vehicle speed at 56 km/h (35 mph) or more and travel for 16 minutes or more.
Return the vehicle to the shop.
After stopping the vehicle, continue idling for 5 minutes, and then turn the ignition switch to the "LOCK" (OFF) position. Moreover, the vehicle should be set to the following conditions for idling.
A/C switch: OFF
Lights and all accessories: OFF
Transmission: Neutral

Sep 15, 2010 | 1998 Mitsubishi Eclipse

1 Answer

'95 ford e150 decelerates by itself while foot on accelerator


Loss of fuel pressure.
1. Clogged fuel filter (replace anyway)
2. Fuel pressure regulator (stays open)
3. Fuel pump

Oct 01, 2009 | 1995 Ford Econoline

1 Answer

Wife driving 2001 Expedition and the Oil light came on, engine seemed to lose power. Traveling approx 70 mph with cruise control set, light came on, cruise control went off and lost power. When i arived 15...


when you travel over 65 mhr for long lenghts of time you don,t work the engine enough to move the fluid to lubricate the engine also when you go on long trips make sure the oil life is still gonna be good for the hole trip

Aug 20, 2009 | 2001 Ford Expedition

2 Answers

Stalls at low speed when in cruise control


You sould have recieved a "recall" notice in the mail about the cruise control for fire and failure issues. they are adding a fusable link where the cruise control harness connects to the brake master cylinder. if you have not had the recall performed yet you should SERIOUSLY consider getting it done, mainly so it doesnt catch fire, but "could" be the result of the failure you've been experiancing! btw, almost ALL Ford vehicles have been affected with the cruise control recall. hope this helps!

Apr 14, 2009 | 2004 Ford Explorer

1 Answer

Charging system light


sounds like a bad alternator the rotor may be flying open at high rpm

Mar 22, 2009 | 2006 Ford Taurus

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

43 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5471 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...