Question about 2004 Chevrolet Silverado 1500 Crew Cab

1 Answer

How do i get the old blower motor out i dropped the cover and its there but cant find the 3 bolts to drop it it looks like it is molded in there this in 2004 silverado

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Contributor
  • 41 Answers

The blower motor twists into case turncounter clockwise to remove there is a locking tab you may have to pull down to release

Posted on Nov 29, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you change front blower motor in 05 dodge caravan


  1. Disconnect and isolate the negative battery cable, then wait 2 minutes before proceeding with the removal. This will effectively disable the air bag system preventing possible personal injury.
  2. Remove the glove box from the instrument panel.
  3. Remove the A/C-heater blower motor cover.
  4. Disconnect the blower motor wiring connector.
  5. Remove the blower motor wiring grommet and feed the wiring through the blower motor housing.
  6. Remove the blower motor mounting screws.
    Allow the blower motor assembly to drop downward to clear the instrument panel and remove from vehicle

Dec 03, 2011 | 2005 Dodge Grand Caravan

Tip

How To Replace A Blower Motor In A 2005 Chevy Trailblazer


Under the passenger side of the dashboard, remove the three 7mm bolts holding the lower plastic cover from the dashboard. Drop down the plastic cover and you will see a square box and 2 or 3 plugs holding to the cover. Unbolt the control box mounted to that cover and the 3 harnesses of wires attached to it, and move them up and out of the way. Look up towards the front corner, the motor is bolted up into the heater box. There are 3 small metric bolts, 4.5mm, I believe, remove those bolts, disconnect the electrical connection to the motor and remove motor. Check the motor electrical connector for any burnt over overheated wires. Alot of these trucks' original connector plug had too small of wiring, causing the power wire to get hot and melt the wire insulation and the plug it's self. The 7 wire plug from the Chevy Dealership is $67.00. You'll need to cut off the old plug and use the connectors supplied with the new plug to replace the old plug. I have seen the blower motor cut off going over a bump, and then come back on after hitting another bump, due to the fact that the individual connector gets hot and melts into the plug. You may also want to look at the blower motor resistor which is mounted right next to the blower motor, sometimes the blower motor resistor will go out altogether, not powering the blower motor, or not allowing the motor to run at a selected speed.

on Mar 09, 2010 | Chevrolet TrailBlazer Cars & Trucks

1 Answer

Replacing blower motor for 1996 chev corsica


Remove lower kick panel passenger side, blower motor in inside heater case, very close to the passenger door, behind glove box. From under the glove box look up to find a circular bulge with 5 (7mm) bolts around it, remove the 2 wire connector (black and purple). Remove the five bolts, drop down the blower motor, transfe over cage if new one doesn't come with one, reverse to reassemble.

Jan 28, 2011 | Chevrolet Corsica Cars & Trucks

2 Answers

My blower quit working for the heater


Look at the motor connector and check for power or burnt. Motor could be bad. if no power then you may need a blower control module too.

Jan 15, 2011 | 1995 Buick LeSabre

2 Answers

I have a 95 jeep cherokee and the heater/blower/AC fan only works in the fastest position. Any idea what is causing this?


Blower motor resistor.
Look under the passenger side dash, you will see a cover that needs to be removed, 1 screw(LH side of the cover and a clip at the back hold it in place). Once off you will see a bunch of wires and a connector. This connector plugs into the resistor. There is also an actuator that you will need to remove. The bolts are tricky to get at. Remove the bolts and actuator pipe and you can get at the resistor bolts which will allow you to pull the resistor from the housing.

Oct 20, 2010 | 1995 Jeep Cherokee

1 Answer

THE BLOWER FOR MY HEAT & AIR WORKS WHEN IT


You need to drop 30 bucks for a blower motor, especially if the intermittent operation is accompanied by any kind of rubbing or squeaking noise. It is located under the glovebox, behind a tight-fitting molded and insulated decorative cover. Removing this cover is the hardest part of the job. It's a truck not a Beemer, so I took mine off and threw it away.
The motor is held on by six or eight 9/32" bolts, and there is one electrical connector that is shaped in such a way as to only go on one way.
Before actually going out and buying the motor, take yours out and check to see if the squirrel cage turns freely. If it does, connect the motor to 12vdc using jumper leads (not jumper cables). If it starts every time, and runs noise-free, you have a problem in the motor control circuit, either in the dash-mounted swirch cluster, or the PCM. Pray it's not the PCM.
Good luck!

Feb 23, 2010 | 1999 Chevrolet Silverado 1500

1 Answer

I was told by a mechanic that my blower motor fan was frozen. he took it out dryed it with a blow dryer he said it worked fine.charged me $200 for the labor. well when it dropped down to 5 degrees the...


No, it's very easy.This is located under the dash on the passenger side of the car.There might be a black cover underneath, pull that off, then your blower is the part that looks like a flying saucer, remove the three bolts that bolt in from the bottom, then pull off your electrical pigtail and you have your blower motor in hand......Hope I could help!!!!!

Feb 01, 2010 | 2006 Chevrolet HHR

2 Answers

Blower motor resistor has failed again for the third time. What is causing the resitor to fail?


The blower motor is drawing to many amps,even if it sounds,and runs fine,this is the main cause for resister failier.

Nov 14, 2009 | Dodge Ram 1500 Cars & Trucks

2 Answers

How to change front blower motor in a 2003 dodge caravan


Removal & Installation
CAUTION The Supplemental Inflatable Restraint (SIR) system must be disarmed before removing the blower motor assembly. Failure to do so may cause accidental deployment of the air bag, resulting in unnecessary SIR system repairs and/or personal injury.

  1. Disconnect and isolate the negative battery cable, then wait 2 minutes before proceeding with the removal. This will effectively disable the air bag system preventing possible personal injury.
  2. Remove the glove box from the instrument panel
d6b70fa.gif
The blower motor is located behind the glovebox, behind the blower motor cover

  1. Remove the A/C-heater blower motor cover.
  2. Disconnect the blower motor wiring connector.
  3. Remove the blower motor wiring grommet and feed the wiring through the blower motor housing.
  4. Remove the blower motor mounting screws.
0e0729c.gif
Once the cover is removed, unplug the electrical connector and push it through the opening in the housing

1ed158c.gif
The blower motor is secured to the housing with three small screws

  1. Allow the blower motor assembly to drop downward to clear the instrument panel and remove from vehicle.
To install:
  1. Place the blower motor assembly into position on the A/C-heater unit and tighten the mounting screws.
  2. Route the blower motor wiring through the blower motor housing and seat the wiring grommet in the hole of the blower motor housing.
  3. Reconnect the blower motor electrical connector.
  4. Install the A/C-heater blower motor cover.
  5. Install the glove box into the instrument panel.
  6. Reconnect the negative battery cable. Check blower motor operation.

Oct 12, 2009 | 2003 Dodge Caravan

1 Answer

Heater Blower Motor


Remove the glovebox door, and the under dash cover/trim panel.

Look behind where the glove box was, you will see the heater box

At the bottom of this box, there is a round plate with a wiring connector and 3 screws holding this plate to the heater box.

This plate is the bottom of the heater fan assembly; remove the connector, and the 3 screws. The fan motor will drop staright down. Real easy to do.

Oct 20, 2008 | 1996 Toyota Avalon

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

49 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8140 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...