Question about 1992 Honda Accord

1 Answer

Vehicle put into drive but wouldn't move.

The accord was turned off and the key removed. Key was replaced a minute later and the vehicle started. However, the vehicle was then put into drive but wouldn't move.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 5 Answers

The tranny fluid might be low or you might also have a plugged tranny filter. Either way you might want to replace both.

Posted on Nov 19, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How to program my key to 98 ford explorer


for Ford keys (1996 -early 1998 Ford, Lincoln, Mercury)

If you want to initiate a new master key....

1. Insert new key into ignition cylinder and turn it to the ON (RUN) position. The security light on the dash will flash for fifteen minutes.


2. When the security light stops flashing, you have FIVE minutes to start the next step. Turn the ignition cylinder OFF and then back to the ON (RUN) position. The security light on the dash will flash for fifteen more minutes.

3. When the security light stops flashing, you have FIVE minutes to start the next step. Turn the ignition cylinder to OFF and then back ON (RUN) position. The dash will flash for fifteen more minutes.

4. After the security light stops flashing the third time, the new key has been programmed into the vehicles computer and will operate the car. It has replaced ALL the previous electronic key codes and is the ONLY key programmed into the vehicles computer.
If you want to add a key....


1. Insert an existing key into the ignition cylinder.


2. Turn the ignition cylinder to ON (RUN) and back to OFF.

3. Remove the existing key and, within 15 seconds, insert the new key and turn it to ON (RUN).

4. The security light will light up for two seconds to indicate success in programming the key into the vehicle.

5. Don't attempt to start the vehicle with any key for at least 1 minute.
<HR>On-Board Programming Method "C"


for Ford keys (Later 1998-newer Ford, Lincoln, Mercury)

If you want to initiate a new master key....

1. This requires that the vehicle be connected to special dealer equipment. There are two ten minute delays involved while this device erases all existing key programming and sets up the vehicle computer to accept new key codes. Two new keys should be ready because the system requires a minimum of two keys in the program. After the first two keys are programmed, additional keys can be entered individually by following the instructions for adding duplicate keys (below).

If you want to add a key....


**You must have two original keys to perform this procedure. If you only have one key, you WILL have to take it to the dealer to get it programmed**


1. Insert and existing (working) key into the ignition cylinder.

2. Turn the ignition cylinder ON (RUN) and back to OFF. Ignition should stay on for at least ONE SECOND.

3. Remove the existing key and, within TEN seconds, insert a second working key and turn it to ON (RUN) and the back OFF. Ignition must be in ON for at least ONE second, but no more than TEN seconds. Remove the key.

4. Insert the new key before TWENTY seconds have elapsed and turn it to ON (RUN). Leave it the ON position for at least ONE secondand turn back to OFF.

5. The security light will light up for THREE seconds to indicate that the new key has been successfully programmed.

6. To program additional keys, repeat steps 1 through 5
As a precautionary measure for all of the above procedures, you should wait at least one minute after you have performed this until you start your vehicle.

Dec 10, 2016 | 1998 Ford Explorer

1 Answer

How to program a 04 malibu new key


When the correct number of learned master keys are not available to perform adding keys procedure the 10 minute re-learn procedure or 30 minute re-learn procedure must be performed. Refer to Programming Theft Deterrent System Components .
30-Minute Relearn Procedure
Use this procedure after replacing any of the following components:
?€¢
The PASS-Key III plus keys


?€¢
The theft deterrent module (TDM)


?€¢
The powertrain control module (PCM)

Important:
?€¢
This procedure is not available on vehicles equipped with EXPORT configured TDMs.


?€¢
When performing the 30-minute relearn procedure, all previously learned keys will be erased from the TDM memory. Additional keys may be learned after performing the relearn procedure.


?€¢
When replacing a TDM with a GM SPO Replacement Part, ensure the procedure to setup a new TDM is performed prior to the 30-Minute Relearn Procedure.

  1. With a master vehicle key, turn ON the ignition, with the engine OFF.
  2. Observe the security indicator. After approximately 10 minutes, the telltale will turn OFF.
  3. Turn OFF the ignition, and wait 5 seconds.
  4. Repeat steps 1-3 two more times for a total of 3 cycles or 30 minutes.
  5. Important: The vehicle learns the key transponder information and/or passwords on the ignition switch transition from OFF to RUN. You must turn the ignition OFF before attempting to start the vehicle.
  6. With a master vehicle key, start the vehicle. The vehicle has now learned the key transponder information and/or the ECM has now learned the fuel continue password.
  7. If additional keys are required to be learned, refer to Adding Keys .
  8. With a scan tool, clear any DTCs.
Adding Keys
Important:
?€¢
To initiate, this procedure requires that a learned master key be available.


?€¢
A total of 10 master keys or valet keys may be programmed to a single vehicle.


?€¢
This procedure adds keys only. The procedure does not erase previously learned keys.


?€¢
The keys to be learned must duplicate the mechanical cut of the current key.


?€¢
If more than one valet key is to be learned, immediately precede each valet key with a learned master key.

  1. With a previously learned master key, turn ON the ignition, with the engine OFF.
  2. Turn OFF the ignition and remove the key.
  3. Within 10 seconds insert the key to be learned. Turn ON the ignition with the engine OFF. The vehicle has now learned the new key.

Jul 05, 2016 | Cars & Trucks

1 Answer

I need to find how to program a transponder key on a 2007 Chevrolet Equinox , VIN starts with a 2


This 30-minute learn procedure should be used when all vehicle keys are desired to be replaced or reprogrammed. This procedure will erase all previously learned vehicle keys from the TDM. Once the 30-minute learn procedure has been completed, any remaining vehicle keys may be programmed using the Adding Keys procedure to ensure their continued functionality.
  1. With an unlearned master vehicle key, turn ON the ignition, with the engine OFF.
  2. Observe the security indicator, after approximately 10 minutes the telltale will turn off.
  3. Turn OFF the ignition, and wait 5 seconds.
  4. Repeat steps 1-3 two more times for a total of 3 cycles or 30 minutes.
  5. Important: The TDM learns the key transponder information upon the ignition switch transition from OFF to ON. You must turn the ignition OFF before attempting to start the vehicle.
  6. With a master vehicle key, start the vehicle. The vehicle has now learned the key transponder information.
  7. If additional keys are required to be learned, refer to Adding Keys.
  8. With a scan tool, clear any DTCs.

Mar 13, 2016 | 2007 Chevrolet Chevrolet Equinox LT

1 Answer

I change the battery in my 2007 equinoxLT AWD and it will not start the shift selector light does not turn red when i shift to drive what is the problem?


You probably lost the programming for the anti-theft. Many cars require you to keep power through the system to keep this from happening when a person changes a battery. Try the following: I found this online, worth a shot. This is to reset the Passlock.
Important: Do not remove the key from the ignition during this procedure. If the key is removed, the procedure will have to be performed from the beginning.
  1. Turn ON the ignition, with the engine OFF.
  2. Attempt to start the engine, then release the key to ON. The vehicle will not start.
  3. Observe the SECURITY telltale. After approximately 10 minutes, the telltale will turn OFF.
  4. Turn OFF the ignition, and wait 5 seconds.
  5. Repeat steps 1-4 two more times for a total of 3 cycles/30 minutes. The vehicle is now ready to relearn the Passlock Sensor Data Code and/or passwords on the next ignition switch transition from OFF to RUN. Important: The vehicle learns the Passlock Sensor Data Code and/or password, the next ignition switch transition from OFF to RUN. You must turn the ignition OFF before attempting to start the vehicle.
  6. Start the engine. The vehicle has now learned the Passlock Sensor Data Code and/or password.
  7. With a scan tool, clear any DTCs if needed. History DTCs will self clear after 100 ignition cycles.

Sep 14, 2014 | Cars & Trucks

4 Answers

My key is stuck in the ignition of my 2006 Audi A4 automatic Tdi. The button on the gear lever is stuck in in Park Mode. When i put the gear lever in Drive or Reverse the button pops out. When i put it...


ask at the dealer i think it may only need a new stop light switch but i could be wrong ,how about leaving the car in neutral ,does key come out then as should do but later cars like this it might not work in neutral though

Feb 14, 2011 | 2006 Audi Q7

1 Answer

I have a 96 Cavalier LS 2.4L, it died on the road while my wife was driving. Some numbnut tried to jumpstart it and hook up the cables wrong... So far I have replaced the bettery, starter, ignition switch,...


After you put in the ecu, do the crank relearn, everyone knows how to do that since its common knowledge, and you're good to go.
Here is how it's done: Ensure that your battery is fully charged before attempting the relearn procedure. Do not leave any battery charger or jumper cables attached to the battery. Close the hood completely. Some applications require that the doors remain closed during the procedure.
96-99 chevy
1. Rotate the key to the start position to attempt to start the vehicle (the vehicle will not start).
Allow the key to return to the all position (same as if the vehicle would have started). The theft system light will flash (or stay lit) on the dash for approximately 10 minutes.
2. When the theft system telltale stops flashing (or turns oft) turn the key to the off position for 5 seconds and then attempt to start the vehicle. The vehicle should start on this cycle.
3. Once the vehicle is running, the password relearn is complete.

00 + chevy
1. Rotate the key to the start position to attempt to start the vehicle (the vehicle will not start). Allow the key to return to the on position. (same as if the vehicle would have started)
2. The theft system light will flash (or stay lit) on the dash for approximately 10 minutes.
3. When the theft system telltale stops flashing (or turns off) turn the key to the off position for 5 seconds and then attempt to start the vehicle.
4. Repeat steps 1 through 3 two more times for a total of 3 cycles/30 minutes.
5. On the next cycle of turning the ignition key from off to crank the vehicle should start
6. Once the vehicle is running, the password is learned and this completes the cycle.
7. Clear any DTC's with a scan tool if necessary. DTC history will be cleared after 100 ignition cycles.

Thank you for using fixya and keep me posted, be glad to help you get the car running 100% again

Apr 26, 2010 | 1996 Chevrolet Cavalier

4 Answers

Volvo xc90 key will turn from 0-1 but wont turn from 1 on to start the vehicle, all lights and radio goes on but the key wont start the car???? all of SUDDEN


Ok, this just happened in our 2000 V70. The key would turn to position 1, the srs light pops on, but the key refuses to turn to start the car and the shifter is stuck in park. I pulled the oil dipstick out, lightly coated the key on ALL sides, inserted it back into the ignition and turned it a little forcibly. It turned so I cycled it back and forth a few times and it was good to go. We were stuck so this was a last ditch attempt to get going....I would suggest using clean, 3 in 1 oil to lubricate the ignition.

Sep 10, 2009 | 2004 Volvo XC90

1 Answer

Key will not turn to start vehicle.


Try pushing in the key while turning the wheel either way. And jiggling it. This happens because the steering locks for the car's protection. If we park it with the wheels turned, it locks in that position. If that does not work, you may have to call a good mechanic to help you.

Jan 22, 2009 | 1993 Isuzu Trooper

Not finding what you are looking for?
1992 Honda Accord Logo

Related Topics:

46 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7772 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...