Question about 2000 Chrysler 300M

1 Answer

I need to replace and then adjust the headlights on my 2000 Chrysler 300M. How do I replace the headlights, then adjust them.

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 2 Answers

Park your vehicle on level ground with the headlights near a garage door or wall. A good distance is 2-3 feet away from the wall or door. The location must be perfectly level and flat at a distance of 10 to 25 feet away from the door or wall.
Switch on the low headlight beams and mark the horizontal and vertical centerlines of each headlight beams on the wall using masking tape. This will mark the center of each beam with a +. The marking will tell you where exactly the headlight beams should be centered from a distance.

Move the vehicle back about 10 to 25 feet away from the garage door or the wall.

Keep the headlights on the low beam setting.
Use the markings you made on the wall or garage door to, check where the light shines and see if the centerlines still match up with the masking tape marks. If the centerlines of the two beams do not align with the tape marks, you can adjust one or both sides as needed.

Make the necessary adjustments with the lights still on while watching the light beams on the wall and your marks.
Turning the top adjusting screws in a clockwise direction will raise the beam while counterclockwise turn will lower it.

Turning the side adjuster screws will adjust the lights to the left or right.

Continue the adjustments until the center of the light beams are aligned with the tape marks. Then adjust the vertical alignment of both beams slightly below the marks on the wall. This will assure that the lights are tilted slightly downward so they won’t blind approaching motorist.

The will align bot lights, the high and low sine both are connected to the same headlight!!

Posted on Mar 05, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Seat adjustment drivers


are the seats power operated , if so may have a mechanical problem with the seat structure , does it go completely flat or not stay where you adjust it to ?

May 23, 2014 | 2000 Chrysler 300M

1 Answer

I need instructions to change headlight assembly on a chrysler 300m yr 2000


If you email me i can send information that way sj196653@yahoo. Dont forget to rate my solution and leave testimonial it is how i earn my achievements Thanks in advance

Apr 22, 2012 | 2000 Chrysler 300M

1 Answer

How do you change the lense cover on 2003 chrysler 300m


if your talking about the headlight outer lens you don`t replace them you replace the headlight assembly.as its a complete unit and non separable.

May 09, 2011 | 2003 Chrysler 300M

1 Answer

How do I go about changing the headlight bulb on a Chrysler 300m 2000.


JUST TWIST AND TURN IT HAS DIFFRENT SIZE,S CONNECTED TO IT SO IT WILL HAVE TO GO BACK IN THE SAME WAY YOU TAKE IT OUT

Mar 09, 2011 | 2000 Chrysler 300M

1 Answer

How to change a 2000 chysler 300m headlight


See my note to Thrasher. Says it all.

Mar 01, 2011 | 2000 Chrysler 300M

1 Answer

Changing the headlight on a chrysler 300m


Not as hard as this sounds, but not as easy as most vehicles either.

Pop open the access hole in the wheel well and remove the fascia screw that points down near the hole.

Remove the 3 plastic rivets on the top where the grill meets the cross beam

Remove the fascia retaining nut accessed through the hole in the wheel well.

Pull the fascia down and forward to open access to the headlights. It might be a little stubborn.

Remove the two long mounting screws holding in the headlamps. Careful not to strip them.

You'll have to wiggle and maneuver the headlights out. You'll have to bend the fascia away, but it's plastic and will give. It's not difficult, but it takes a little finesse.

Once the bulbs are replaced, reverse the process.

Jun 11, 2009 | 2000 Chrysler 300M

1 Answer

Changing headlight 300m


lift the hood. the light are down behind the light assembly. simply turn large black ring and it will come out. be carefull not to touch the glass on the new one. oil from your skin will cause it to prematurely fail.

Mar 11, 2009 | 2004 Chrysler 300M

2 Answers

My Chrysler 300m headlights will not turn off.


you have a stuck headlight relay...replace it.

Feb 08, 2009 | 2000 Chrysler 300M

Not finding what you are looking for?
2000 Chrysler 300M Logo

709 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

76691 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8531 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...