I am still leaking fluid where the clutch line connects to the slave cylinder i have replaced the washers and the cylinder itself but it still leaks in the same spot

The clutch hydraulic system is very simple, just 3 pieces. There is the clutch master cylinder with attached fluid reservoir-mounted on the firewall, there is a steel line from the master going down to the transaxle bell housing, and there is the clutch slave cylinder on the bell housing that the steel line connects to.
If yours is leaking under the car, it is probably the slave cylinder, either that or the steel line. Either one should be easy to replace.

the most likely reason is either the clutch master cyl. needs to be replaced.or the.slave cyl. its mounted down on the transmation under the hood find the resivore for the clutch. check the fluid level.if its low , fill it back up , and look for signs of a leak
you will probally have to bleed out all of the air from the system.its done almost the same way as bleeding the brakes. Good Luck.

Yes all 92-95 civics have a hydraulic clutch system. it starts at the pedal. Pedal pulls a plunger in the clutch master cylinder which is found bolted through the firewall under the hood on the drivers side. The master cylinders resivoir is bolted to the drivers side strut tower and connected to the master cylinder with a rubber hose. A line from the master cylinder runs along the firewall tirades the passenger side wheel then turns to the front of the car and is connected with a fitting to a rubber hose. The rubber hose runs to your clutch slave cylinder. The slave pushes the clutch arm. Your clutch pedal is staying on the floor because there is no back pressure to push it back up. You have air in your clutch system. First find out why (find leak or just top up clutch master cylinder with brake fluid if no leaks) then bleed your clutch. If your clutch line is rusted there is a coupler mid way in the line on the firewall. Will save you from removing the whole line maby. And there is no need to bench bleed the clutch master cylinder. My guess is your slave cylinder is leaking. It right on the front of the transmission. Pull back the rubber boot over the end of the slave cyl. and check for fluid leaks. The bleed screw is on top of the slave cyl. Find/fix leak, fill resivoir, pump clutch 10 times then HOLD. Open bleeder screw, watch for fluid and air sputtering out or just air. CLOSE valve, release clutch. REPEAT until clutch works keeping resivoir topped up. You may also open bleeder screw and pump clutch to get fluid into the system before you do the bleed process. Keep in mind brake fluid eats paint and is not very nice on your skin or in your eyes so be carefull with it. There may also be an off chance your pedal sticks because the clutch itself is badly broken but it's not really very likely.

you need to inspect the clutch hydraulic system to look for a leak.check in the truck were the master cylinder bolts to the firewall as if the master is leaking out the back it will show up the leak in this area.check around the master under the hood to see if there are signs of it leaking.check at the transmission were the slave cylinder is as this is another place they leak.if you have to fill the master because its empty there is a leak somewhere.you also may need the clutch replaced as the slave cylinder moves out to adjust for wear of the clutch which will lower the fluid level but not cause it to be empty.you will have to bleed the clutch system at the slave cylinder,there should be a bleeder screw to do this.if you find the leak in the clutch system you will have to replace the system as some come complete master lines and slave.some come with just the slave,lines,master as separate components.

No, you don't need to replace the clutch itself.
Don't be surprised if the slave cylinder replacement doesn't fix it.
Could be the master cylinder.

Examine carefully to locate exact point of leak. Could be the hydraulic line, a connection between line & slave cylinder or master cylinder, or a bad slave cylinder. Once you identify the point of leak, I can help you with repair info if needed.

leaky slave or master cylinder - if you have someone listen to the slave cylinder while you press the pedal is should "squelch" if there is air in there, if the slave cylinder doesn't make a squelching sound then the master cylinder or a hydraulic line between the two cylinders is leaking - slave cylinder isn't very expensive but the master cylinder can be rather pricey. and any good parts shop or motor-factor can source or make-up a new hydraulic line if it is the line itself that is leaking.

more than likely the slave cylnder in the tranny or on the side of the tranny have you been seeing fluid on the ground.

Use a copper washer like on the brake lines, not an o ring.

Slave cylinder should be on the left side of the bellhousing (follow the line from the clutch master if necessary) If you don't see fluid but you have lost some, also check where the rod from the pedal goes through the firewall to the master...they often leak there and will not drip on the ground.