Question about 2001 Chevrolet Silverado 1500

Open Question

Why is it making a grinding noise when i press the gas

OK its like a crank up its fine, but when i put it in gear a press the gas it make a grinding noise only when press the gas

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
j_del
  • 1586 Answers

SOURCE: Reverse gear has grinding noise...?

Have them flush the fluid out under warranty and put in new fluid, and have them bleed the clutch lines in case air is getting in there. Audi and VW claim lifetime transmission fluid but it's BS - I've changed relatively low mile fluid from these cars and it was horrendous. It's possible that the fluid itself is causing trouble, but it's more likely that it is a synchro problem. If it was a clutch issue, you should have problems with more than just reverse gear - a clutch simply engages and disengages the engine and transmission, regardless of which gear it is. The problem (if not fixed by fluid) is in the transmission, and being under warranty, don't accept another "suggestion" like they're giving you. Changing your clutch isn't gonna do it.

Posted on Aug 12, 2008

Ad
  • 49 Answers

SOURCE: tranny problems

did you change the bearing in the flywheel the center one or throw out bearing that pushes out on to the presserplate

Posted on Jan 18, 2009

  • 260 Answers

SOURCE: 1994 Chevy truck cranks fine, but when gas is pressed it cuts off

Did you change the fuel filter yet?

Posted on Apr 28, 2009

  • 119 Answers

SOURCE: VW GOLF 1.4 1999 S. Gearbox makes whining sound at idle

No good news on this one I think
Your whining sound problem is the Layshaft bearings in the gearbox are badly worn. It also seems that the baulk rings are damaged on 5th gear.
John

Posted on Aug 19, 2009

MauiRentaCar
  • 288 Answers

SOURCE: clicking sound when i press the gas pedal

The clicking and popping sound like a problem with the CV joints. The best repair for this is to replace the CV half-shafts. The brake noise may or may not be related to this issue. If the noise is coming from the front, it could be that you need new brake pads, or that the rotors need to be resurfaced, or the brakes may need some other adjustment. If the noise is coming from the rear, you may need new brake shoes, or the drums need to be resurfaced, or there could be another issue. Have the brakes checked out when the CV axles are replaced.

If you need more help with these issues or if you have any more questions just let me know.

Posted on Mar 30, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2006 chev v8 auto tranmission want go into gear makeing a rowing noice when you crank it


start from furthest u joint on driveshaft (at differential) and work your way up to tranny. check u joints very carefully and thoroughly. if drive line checks out tranny or torque converter is bad. specially when rough grinding noises are heard when put into gear. cranking as you said i refer to starting engine. i assumed you meant when selecting gear with motor on. if there is a noise when you crank engine to start it, then check starter and flexplate (cracked).

Oct 09, 2017 | Cars & Trucks

1 Answer

Grinding noise when in gear


Sad to say but you will be needing to get a new transmission ..

Sep 17, 2015 | 2004 Chrysler Town & Country

1 Answer

Grinding clutch


I'm a little confused on your description of the noise. If I understand you correctly It is making the noise when it shifts smoothly into gear but at the same time it makes a grinding noise ? It possibly can be synchronizers if the grooves on the inside of the synchronizers are worn bad enough to where the gear isn't slowing down enough causing a grind as the clutching teeth on the gear mesh with the synchrode and the shift collar.
If it is making noise in all gears except 4th you may have countershaft brgs failing. The power flow in 4th gear goes directly through the mainshaft and has a 1 to 1 ratio. All other gears the powerflow goes through the countershaft causing a load on the countershaft so if you have bearings failing in the countershaft you will hear noise in all gears but 4th.
i hope I understood you correctly .

Jan 18, 2014 | 2002 Subaru Forester

1 Answer

I have 1997 GMC Suburban. It will crank but when you have it in gear it goes no where when you press the gas and makes a loud noise. Was told it might be the flywheel. I am not a mechanic and don't have...


If it's not a transmission problem, which is usually the case, I would check to make sure your drive shaft is still connected and that the u-joints are in good shape. If you can possibly see under the truck while someone presses the gas, you can see if the drive shaft is turning. If the drive shaft is spinning and its still not engaging, that loud noise may very well be the gears grinding/broke inside the back axle (rear differential). Just a few things to check, hope it helps in some way!

Dec 07, 2013 | Cars & Trucks

1 Answer

I have a 1989 z24 cavilier and i just changed the slave cylinder and now when i start it and press the clutch it makes a grinding noise. When i try to put in gear it wont go in any gears and makes some...


hi i was wondering if anyone can tell me whats going on with my 89 z24 cav i just replaced two shifter cables on she's a 2.8l 5 speed and now when i starts her and lets the clutch out she dosen't engage at all but she has no noises and no grinding goes in gear fine but just won't move hope someone can help thanks

Jul 04, 2012 | Cars & Trucks

1 Answer

Car make a fast grinding noise and engine does not crank or turn over at all the lights and windows work fine when battery is on.


suspect the starter or ring gear, remove the starter and inspect the drive gear , if damages check the ring gear all around, if ant teeth are damaged it will need replacing

Apr 15, 2011 | Mercury Cougar Cars & Trucks

1 Answer

After stopping the car to get gas I then cranked it and all the dash panel lights came on and the car would only go slowly when I pushed the gas pedal. I then stopped the car and turned it off then cranked...


Is your check engine light still on? If so, you need to take it to get scanned at Autozone. It could be several different things causing this to happen. Has it been overheating? Is the correct amount of oil in the car? Transmission fluid?

Mar 03, 2011 | 2008 Ford Taurus

2 Answers

When my 1997 ford explorer 4wd 181000 miles it makes a grinding noise when i let off gas when i gas it it quits what could this be it does it only when i coast like driving 55 or it started in reverse but...


I have a 97 ford explorer sport 4x4. When i drive at a constant speed it's fine but when i let off the gas I hear a grinding noise. if i put in nutral as soon as i hear it the noise quits areif I shoot the gas to it it quits. What could it be?

Jul 15, 2010 | 1997 Ford Explorer AWD

1 Answer

Rear-end grinding noise in 1993 GMC Sierra 1500


your description sounds like the gears inside the the same differential you just replaced.

Oct 13, 2009 | 1993 GMC Sierra K1500

1 Answer

Grinding noise coming from 97 GMC Yukon transfer case


Hi!!!! I have the same problem with mine. Did you solve it????

Oct 01, 2009 | 1992 GMC Yukon

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

171 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...