Question about 2001 BMW 330

1 Answer

Fuel pressure low at pressure monitor - 2001 BMW 330

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 6,784 Answers

HI. There are some areas that will need to be checked for faults, in this case. Check the following:

1. Fuel filter- If this device is clogged, or faulty, it will decrease the flow of fuel to the injector assembly. If the filter hasn't been changed recently, this will be a good place to start.

2. Fuel pump- This device may be weak, or grounded poorly. check the ground, and all wires the link the pump to the power source. replace any corroded contacts and connectors. wires,as well, if needed.

3. Fuel pressure regulator- The fuel pressure regulator is used to keep the fuel pressure in the fuel rail consistent and change the fuel pressure depending on the throttle position. The fuel rail is in a fuel loop between the fuel pump feed and return lines. Because the fuel delivery requirements change depending on the engine's throttle position and engine loads, the fuel injection system must be able to adapt to meet the fuel requirements of the engine's operating conditions during idle, acceleration and steady cruising.The fuel pressure regulator has a small vacuum line attached to it that allows the pressure regulator to change the fuel pressure in the fuel loop depending upon the intake manifold pressure which changes as the throttle position changes. When the throttle is opened, the manifold vacuum pressure drops off, causing the pressure regulator to increase the fuel pressure in the fuel loop, which increases the amount of fuel delivery at the injectors to provide for the additional fuel needed for the engine to operate properly.At idle, the manifold vacuum increases and the demands for the rate of fuel delivery are decreased so the pressure regulator decreases the fuel pressure in the fuel loop.

1. Look for visible evidence of fuel leaks.
2. A pressure regulator can become defective due to foreign material or a ruined diaphragm.


The result will be hard starting, poor idle quality, and lack or power. Burned spark plugs can result from operating with a lean air/fuel mixture, as well. replace this device if faults exist.

Posted on Nov 18, 2009

  • Michael Masters
    Michael Masters Nov 18, 2009

    The pressure regulator will be mounted directly on the end of the fuel rail.

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Vehicle CEL is on, various codes


P0300 is a random miss fire , a vacuum leak can cause this as well as low fuel pressure ! weak fuel pump , clogged fuel filter !
DTC P0171: Fuel Trim System Lean Bank 1
DTC P0174: Fuel Trim System Lean Bank 2 These two codes are saying the PCM - engine computer is see a lean condition .
DTC P0191: Fuel Rail Pressure (FRP) Sensor Performance
Circuit/System Description
The fuel pressure sensor is located on the fuel line. The fuel pressure sensor monitors the fuel pressure in the fuel line. The fuel pump flow control module (FPCM) monitors the voltage signal from the fuel pressure sensor.

You don't say what make , model an year vehicle ! These are for GM vehicles , yours could mean something else . Except the first three , those are genaric codes , same for all makes ! So can't say what this codes are P2097, and P2099 ! Can't mean this P2097 - Post Catalyst Fuel Trim System Too Rich Bank 1
P2099 - Post Catalyst Fuel Trim System Too Rich Bank 2

Sep 03, 2016 | Cars & Trucks

1 Answer

Which of the four probable causes for DTC P0191 is most likely?


P0191 - Fuel Rail Pressure Sensor Circuit Performance (FRP) The comprehensive component monitor (CCM) monitors the FRP pressure for acceptable fuel pressure. The test fails when the fuel pressure falls below or exceeds a minimum/maximum calibrated value for a calibrated period of time. High fuel pressure.
Low fuel pressure.
Damaged FRP sensor.
Excessive resistance in circuit.
Low or no fuel.
A FRP PID value during KOER of 138 kpa (20 psi) and 413 kpa (60 psi) for gasoline or 586 kpa (85 psi) and 725 kpa (105 psi) for natural gas vehicles (NG) is acceptable. You will have to check these items to find the cause of the code. no short cuts.

Sep 02, 2015 | 2003 Ford Explorer Sport XLT

1 Answer

Error code p1041 and p1047 02 chrysler sebring lxi 2.7L


Definition of Diagnostic Trouble Code P1041 Saab: Injector Cylinder 4 Shorting To Ground

There is no definition for DTC P1047

CodeDescription P1192 Inlet Air Temp. Circuit Low P1193 Inlet Air Temp. Circuit High P1195 1/1 O2 Sensor Slow During Catalyst Monitor P1196 2/1 O2 Sensor Slow During Catalyst Monitor P1197 1/2 O2 Sensor Slow During Catalyst Monitor P1198 Radiator Temperature Sensor Volts Too High P1199 Radiator Temperature Sensor Volts Too Low P1281 Engine Is Cold Too Long P1282 Fuel Pump Relay Control Circuit P1283 Idle Select Signal Invalid P1284 Fuel Injection Pump Battery Voltage Out Of Range P1285 Fuel Injection Pump Controller Always On P1286 Accelerator Pedal Position Sensor Supply Voltage Too High P1287 Fuel Injection Pump Controller Supply Voltage Low P1288 Intake Manifold Short Runner Solenoid Circuit P1289 Manifold Tune Valve Solenoid Circuit P1290 CNG Fuel Pressure Too High P1291 No Temp Rise Seen From Fuel Heaters P1292 CNG Pressure Sensor Voltage Too High P1293 CNG Pressure Sensor Voltage Too Low P1294 Target Idle Not Reached P1295 No 5 Volts To TP Sensor P1296 No 5 Volts To MAP Sensor P1297 No Change in MAP From Start To Run P1298 Lean Operation At wide Open Throttle P1299 Vacuum Leak Found (IAC Fully Seated) P1388 Auto Shutdown (ASD) Relay Control Circuit P1389 No Auto Shutdown (ASD) Relay Output Voltage At PCM P1390 Timing Belt Skipped One Tooth or More P1391 Intermittent Loss of CMP or CKP P1398 Mis-Fire Adapter Numerator at Limit P1399 Wait To Start Lamp Circuit P1403 No 5 Volts To EGR Sensor P1475 Aux. 5 Volt Output Too High P1476 Too Little Secondary Air P1477 Too Much Secondary Air P1478 Battery Temp Sensor Volts Out of Limit P1479 Transmission Fan Relay Circuit P1480 PCV Solenoid Valve P1482 Catalyst Temperature Sensor Circuit Shorted Low P1483 Catalyst Temperature Sensor Circuit Shorted High P1484 Catalytic Converter Overheat Detected P1485 Air Injection Solenoid Circuit P1486 Evap Leak Monitor Pinched Hose P1487 Hi Speed Rad Fan CTRL Relay Circuit P1488 Auxiliary 5 Volt Supply Output Too Low P1489 High Speed Fan CTRL Relay Circuit P1490 Low Speed Fan CTRL Relay Circuit P1491 Rad Fan Control Relay Circuit P1492 Battery Temperature Sensor Voltage Too High P1493 Battery Temperature Sensor Voltage Too Low P1494 Leak Detection Pump Switch or Mechanical Fault P1495 Leak Detection Pump Solenoid Circuit P1496 5 Volt Supply Output Too Low P1498 High speed Rad Fan Ground CTRL Rly Circuit P1594 Charging System Voltage Too High P1595 Speed Control Solenoid Circuits P1596 Speed Control Switch Always High P1597 Speed Control Switch Always Low P1598 A/C Pressure Sensor Volts Too High P1599 A/C Pressure Sensor Volts Too Low P1602 PCM Not Programmed P1680 Clutch Released Switch Circuit P1681 No I/P Cluster CCD/J1850 Messages Received P1682 Charging System Voltage Too Low P1683 Speed Control Power Relay Or Speed Control 12 Volt Driver Circuit P1684 Battery Disconnected Within Last 50 Starts P1685 Skim Invalid Key P1686 No SKIM Bus Message Received P1687 No Cluster Bus Message P1688 Internal Fuel Injection Pump Controller Failure P1689 No Communication Between ECM & Injection Pump Module P1690 Fuel injection pump CKP Sensor Does Not Agree With ECM CKP Sensor P1691 Fuel Injection Pump Controller Calibration Failure P1693 DTC Detected In ECM Or PCM P1694 No CCD Messages Received From ECM P1695 No CCD/J185O Message From BCM P1696 PCM Failure EEPROM Write Denied P1697 PCM Failure SRI Mile Not Stored P1698 No CCD Messages Received From PCM P1719 Skip Shift Solenoid Circuit P1740 TCC Or OD Solenoid Performance P1756 Governor Pressure Not Equal To Target At 15?20 PSI P1757 Governor Pressure Above 3 PSI When Request Is 0 PSI P1762 Governor Pressure Sensor Offset Improper Voltage P1763 Governor Pressure Sensor Voltage Too High P1764 Governor Pressure Sensor Voltage Too Low P1765 Trans 12 Volt Supply Relay Control Circuit P1899 Park/Neutral Position Switch Stuck In Park or In Gear

Read more at: http://www.obd-codes.com/trouble_codes/dodge/
Copyright © OBD-Codes.com

Jul 26, 2015 | Chrysler Cars & Trucks

1 Answer

My Hyundai 1999 model CHECK ENGINE LIGHT IS ALWAYS ON AND THE FUEL CONSUMPTION IS HIGH.


Do you have black smoke or what looks like soot coming out of the tail pipe. The check engine light monitors fuel pressure through the computer and pressure regulator. It will come on if the pump pressure is too high or too low. If the pressure regulator is faulty it could cause excessive fuel consumption,

Jan 19, 2015 | 1999 Hyundai Sonata

1 Answer

The engine light is staying on.I had a Domestic done on it at autozone--troubleshooting report PO193.Definition:Fuel rail pressure sensor condition--Explanation:The powertrain control module monitors the...


try changing your fuel filter it may solve your problem. after changeing fuel filter disconnect battery for 30 minutes if your light stays off problem solved.if this was helpful please leave me good feedback

Apr 12, 2013 | 2004 Ford Freestar

1 Answer

Ford focus 2.0 tdci c max engine cut out wont start recovery man thinks it is problem with fuel system low preasure how do i check


if there is a Shrader valve on the fuel rail you need to hook a fuel pressure tester up to it. if not then you need a scan tool to monitor pressure or an inline pressure tester. should be 35-50 psi

Oct 10, 2011 | 2004 Ford Focus

1 Answer

(KIA sorento)fuel pressure monitoring-mal multitude by what problem?


Fuel pressure sensor is faulty or pressure is to low.

Mar 24, 2011 | 2005 Kia Sorento

1 Answer

Where could I find a list of Fault Codes for my 3.3 Litre Voyager?


CHRYSLER OBDII DTC

P1101 HCM/PCM Communication Performance

P1103 Turbocharger Waste Gate Actuator Malfunction

P1104 Turbocharger Waste Gate Solenoid Malfunction

P1105 Fuel Pressure Solenoid Malfunction

P1195 Slow Switching O2 Sensor Bank One Sensor One During catalyst monitoring

P1196 Slow Switching O2 Sensor Bank two Sensor one During catalyst monitoring

P1197 Slow Switching O2 Sensor Bank One Sensor two During catalyst monitoring

P1198 Radiator Temperature Sensor Input voltage too high

P1199 Radiator Temperature Sensor Input voltage too low

P1281 Engine is cold too long

P1282 Fuel Pump Relay control circuit

P1283 Idle select signal invalid

P1284 Fuel Injection pump battery voltage sensor out of range

P1285 Fuel Injection pump controller always on

P1286 Accelerator Position Sensor (APPS) supply voltage too high

P1287 Fuel Injection pump Controller Supply voltage low

P1288 Intake manifold short runner tuning valve solenoid circuit

P1289 Manifold tune valve solenoid circuit

P1290 CNG Fuel system pressure too high

P1291 No Temp rise seen from intake heaters

P1292 CNG Pressure sensor voltage too high

P1293 CNG Pressure sensor voltage too low

P1294 Target idle not reached

P1295 No 5 volts to TP sensor

P1296 No 5 volts to MAP sensor

P1297 No change in MAP sensor from start to run

P1298 lean operation at wide open throttle

P1299 Vacuum Leak detected (IAC fully seated)

P1300 Ignition timing adjustment circuit failure

P1388 Auto shutdown relay control circuit

P1389 No ASD relay output voltage at PCM

P1390 Timing belt skipped one tooth or more

P1391 Intermittent loss of CMP or CKP

P1398 Mis-Fire Adaptive Numerator at Limit (PCM is unable to learn the crank sensors signal

for use in preparation for misfire diagnostics

P1399 Wait to start lamp circuit

P1403 No 5 volt feed to EGR

P1475 Auxiliary 5 volt supply is too high

P1476 Too little secondary air

P1477 Too much secondary air

P1478 Battery Temp Sensor Volts out of limit

P1479 Transmission Fan Relay Circuit

P1480 PCV Solenoid Circuit

P1481 EATX (Electronic Automatic Transaxle) RPM pulse generator performance

P1482 Catalyst Temperature Sensor Circuit shorted low

P1483 Catalyst Temperature Sensor Circuit shorted high

P1484 Catalytic Converter overheat detected

P1485 Air injection solenoid circuit

P1486 EVAP Leak Monitor found a pinched hose

P1487 Hi Speed Fan #2 Circuit

P1488 Auxiliary 5 volt supply output is too low

P1489 High speed fan control relay circuit

P1490 Low speed fan control relay circuit

P1491 Radiator fan relay control circuit

P1492 Ambient/ Battery Temp sensor input voltage too high

P1493 Ambient/ Battery Temp sensor input voltage too low

P1494 Leak detection pump pressure switch or mechanical fault

P1495 Leak detection pump solenoid circuit

P1496 5 volt supply, output too low

P1498 High speed radiator fan ground control relay circuit

P1500 General alternator 'FR' Terminal circuit fault

P1594 Charging system voltage too high

P1595 Speed control solenoid circuits

P1596 Speed control switch always high

P1597 Speed control switch always low

P1598 A/C pressure sensor input voltage too high

P1599 A/C pressure sensor input voltage too low

P1680 Clutch released switch circuit

P1681 No I/P Cluster CCD/ J1850 messages received

P1682 Charging system voltage too low

P1683 Speed control servo power control circuit

P1684 The battery has been disconnected within the last 50 starts

P1685 The SKIM (Smart Key Immobilizer Module) has received an invalid key

P1686 No SKIM (Smart Key Immobilizer Module) bus message received

P1687 No Mechanical Instrument cluster bus message

P1688 Internal Fuel injection pump controller failure

P1689 No communication between the ECM and injection pump module

P1690 Fuel injection pump CKP sensor does not agree with the ECM CKP sensor

P1691 Fuel injection pump controller calibration error

P1692 Fault in companion Engine control module

P1693 A companion DTC was set in both the ECM and PCM

P1694 No CCD message from PCM- Aisin transmission

P1695 No CCD message from body control module

P1696 PCM failure EEPROM write denied

P1697 PCM Failure SRI (Service Reminder Indicator) mileage not stored

P1698 No CCD message from TCM

P1719 Skip shift solenoid circuit

P1740 TCC solenoid or overdrive solenoid performance

P1756 Governor pressure not equal to target at 15-20 psi

P1757 Governor pressure is above 3 PSI when 0 PSI is requested

P1762 Governor pressure sensor offset improper voltage

P1763 Governor pressure sensor voltage to high

P1764 Governor pressure sensor voltage to low
P1765 Transmission 12 volt supply relay control circuit

Oct 03, 2010 | 1998 Plymouth Voyager

2 Answers

Low fuel pressur in bmw x6


If it just came on that there is low fuel pressure the first thing you should check is if there is a fuel filter(some vehicles don't have a changeable filter) and change it because they can plug up and restrict fuel flow over time. If the low fuel warning doesn't go out get your fuel pressure checked. Usually about 1/2hr charge in most shops.

May 04, 2010 | 2008 BMW X6

1 Answer

Trouble code shows po452 which is the evap


P0452 Evap.Emission System-Pressure Sensor Low Input

The evaporative emission control system prevents hydrocarbon vapors from escaping from the fuel tank into the atmosphere where they could form photochemical smog. Gasoline vapors are collected in the charcoal canister. The Fuel Tank Pressure Sensor (FTPS) is an integral part of the evaporative monitoring system. The PCM monitors the FTPS signal to detect vacuum decay and excess vacuum. The FTPS measures the difference between the air pressure inside the fuel tank and outside air pressure to check the purge control solenoid valve operation and for leak detection in the evaporative emission control system by monitoring pressure and vacuum levels in the fuel tank during the purge control solenoid valve operating cycles.

Feb 12, 2010 | Hyundai Motor 2003 Elantra

Not finding what you are looking for?
2001 BMW 330 Logo

607 people viewed this question

Ask a Question

Usually answered in minutes!

Top BMW Experts

Frankie B

Level 2 Expert

65 Answers

Fred Sops

Level 2 Expert

272 Answers

Doberman

Level 2 Expert

254 Answers

Are you a BMW Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...