Question about 2000 Nissan Maxima

1 Answer

How do I install the Drivers side rear marker light replacement bulb located just above the left rear tire on my 2000 Maxima?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

    Governor:

    An expert whose answer got voted for 20 times.

  • Expert
  • 188 Answers

The marker is only clipped in so all you need do is push it forward then pull it out

Posted on Nov 18, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 2000 maxima...when headlights are on, passenger side blinker stays lit on the dash and doesn't flash at all. While the headlights are off and i turn the passenger turn signal on it then b


Plain and simple...Your turn signal circuit is shorted to your headlamp circuit. What USUALLY causes this is an incorrect light bulb has been installed in the vehicle or the light bulb was installed incorrectly. There are other possible causes of these circuits being shorted together, but 99 out of 100 of the times that I have seen this it is either because somebody just replaced a bulb or a bulb socket melted somwhere on the car. Be sure to check both the front AND rear bulbs.

Jan 07, 2012 | 2000 Nissan Maxima

1 Answer

Fuse location for 2000 nissan maxima marker lights


Before you get started, please review this article: Where's The Fuse?

Keeping the information in the article above in mind, the fuse that supplies power to the marker lights is located in the engine compartment fuse block It is fuse# 60. it is a 10 Amp fuse. This fuse supplies power to the Tail Lamp Relay which is located in relay box #1. This relay is controlled by the Auto Light Control Unit, which in turn, is controlled by the main lighting switch.
The Auto Light Control Unit gets its power from fuse #30 (10 Amp) which is located in the Instrument panel fuse block under the left side of the dash.

Mar 26, 2011 | 2000 Nissan Maxima

1 Answer

Replacing a turn signal bulb....Baffled...Thanks


Hello,

Please do not be baffled. To replace the turn signal bulb on Your car is quite simple, all You need to do is to get a screwdriver and follow the steps below:
  1. Open the hood and locate the mounting screws for the outboard marker-light assembly just above the light. Remove the screws with a Phillips screwdriver, then remove the assembly, setting it aside for now.
  2. Locate the two mounting screws on top of the turn-signal light assembly under the side-marker lens. Remove the two screws with a Phillips screwdriver, then set the screws aside. Slide the turn signal out and locate the socket on the back of the assembly.
  3. Rotate the bulb socket counterclockwise and pull the socket out of the assembly. Pull the bulb straight out of the socket and discard it. Install a new bulb into the socket, pushing it in until is seats. Position the socket back into the rear of the light assembly, turn it clockwise to lock it in place, then slide the assembly back into the front of the Jeep.
  4. Install the mounting bolts that secure the turn-signal light assembly, tightening the screws with a Phillips-head screwdriver. Position the side marker-light assembly to the side of the Jeep and install the retaining bolts.
  5. Tighten the retaining bolts for the side-marker lights with a Phillips screwdriver, then close the hood. Test the repair by turning the lights on and visually verify that the light is working..
Hope this helped. Thank You for using FixYa!!!

Jan 28, 2011 | 1998 Jeep Grand Cherokee

2 Answers

My rear marker/ running lights are out and i need to know how to get to them


Signal and Marker Lights Removal & Installation To Remove:
  1. Remove or disconnect the following:
    • Screw from the side marker lamp.
    • Side marker lamp from the front and/or rear bumper fascia.
    • Bulb/socket from the side marker lamp.
    • Bulb from the socket.
To Install:
  1. Install or connect the following:
    • Bulb to the socket.
    • Bulb/socket to the side marker lamp.
    • Side marker lamp to the front and/or rear bumper fascia.
    • Screw to the side marker lamp. Tighten to 2 N.m (18 lb in ).
prev.gif next.gif

Jan 08, 2011 | 2002 Pontiac Sunfire

1 Answer

Change left front parking/marker light bulb


Raise the hood, look at the back side of the marker light, if you can see the socket for the bulb, turn it and it should pull out of the light. If you cannot see the back side of the light and locate this socket, you may have to remove the light assembly from the vehicle to access this socket. Hope this helps.

Dec 11, 2009 | 2000 Lexus LX470

1 Answer

How do you change the rear side marker lights?


If you mean replace burned bulbs, find the marker light and locate the wires on the back. Get a good hold on the plug and turn in 45 to 90 degrees and then pull out, replace the bulb and re-install.

Sep 08, 2009 | 2003 Volvo S40

2 Answers

Rpm sensor location


MY MAXIMA 2000 AFTER 800000 MILES was stalling when sitting in traffic for a while especially when the temperature was very hot, i replaced the revolution sensor wich is located behind the the transmission on the drivers side just remove the tire and a small plasic cover and you'll be able to see it.I went to nissan and got the part for about 150 dollars and guess what saved me about 1500 the cost of rebuilding the tranny.

Aug 08, 2009 | 2000 Nissan Maxima

1 Answer

Replace side marker light on lexus rx300


Remove 3 - 4 screws on fender cover close to side marker light. Pull fender cover out a bit for you to use your other hand to reach side marker light. By twisting on one direction and here you go the light out. Replace new bulb and replace everything on reverse order.

Jul 25, 2009 | 2000 Lexus RX 300

1 Answer

Replace front side running light in a 2000 Lexus RX300


Unscrew 3 - 4 screws on the front tire fendor cover close to your side marker light. Pull the fender cover out, use your other hand to reach the side marker light. Using twist and pull the light set out. Replace a new light bulb. Replace everything in a reverse order.

Mar 18, 2009 | 2000 Lexus RX 300

1 Answer

Side marker lights do not work


Hi

No 1 ..Take the lenses off, and check the bulbs, and renew if necessary, check the bulb holder terminals for corrosion, if so spray with WD40 and clean, (with the lights off).

If this does not get them going , you will need a 12 volt test light, and test for live feed to the bulbs lamp holder, with the lights switched on.

Expect you will find corrosion is the problem.

Good Luck

Don´t forget to give a FixYa rating please !

John.



Feb 03, 2009 | 2000 Nissan Maxima

Not finding what you are looking for?
2000 Nissan Maxima Logo

130 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

723 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...