Question about 1991 Dodge Ram 150

1 Answer

Signal light stop working, I checked the fuse and replace it the prob still there

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 133 Answers

CHECK BOTH THE FRONT AND REAR BULBS

Posted on Nov 18, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

No turn signals possible bad ground


If you only have 7 volts at that fuse your problem is in the power side of the circuit ! You need a power distribution diagram to find where that fuse gets it's power from , you have unwanted resistance in that circuit . It's not a ground problem , you need to do voltage drop testing on that circuit ! Do your brake lights work ? The power for the turn signal , ABS , Stop , an SRS fuse's in the left side instrument panel fuse block come fro the ignition switch ! Your ignition switch may be the problem ! SRS is air bag system !

Aug 05, 2015 | 2000 Chevrolet Monte Carlo

1 Answer

I have a 98 eclipse. I was putting new tail lights on and then the signals stopped working along with the brake lights. the fuse to the brake lights had burnt so I replaced it. The signals however are...


IF THE TURN SIGNALS STILL WORK IN THE FRONT, THAT MEANS THE FUSE & THE FLASHER ARE OK. IF THE SIGNALS DON'T WORK AT ALL CHECK TURN SIGNAL FUSE & STOP / BRAKE FUSE. ARE YOU SURE THE CORRECT BULBS ARE BEING USED?

Jan 24, 2011 | 1998 Mitsubishi Eclipse

1 Answer

Turn signals stopped working. Fuses are all ok,


sounds like the flasher can might have stopped working, you will need to get it replaced, it regulates the indicaters to blink, when it goes the circuit is gone, time for replacing id say. check the relays in the main fuse box under the bonnet first, try swapping the relay with another one like the horn relay just to test that first.

Jun 21, 2010 | 1999 Cadillac DeVille

1 Answer

My brake, hazard and turn lights dont work, i


well u have two seprate problems the hazards and turn signals have a flasher that needs replacing if the fuse is good on the fuse box marked signals .and there is a brake light switch under the dash board near the brake pedal it has two wires on it check the wires make sure they are connected if so replace the brake light switch

Nov 13, 2009 | 2002 Chevrolet Astro

1 Answer

Signal lights won t work on a 78 Cutlass Supreme


try checking if you got power going to the socket. It could also be the switch itself.

Jun 02, 2009 | 1987 Oldsmobile Cutlass Supreme

1 Answer

Rear brake lights don't work


you prob got a trailer plug prob bad wires if not tail lights run through turn signal switch tell fix ya bout me ok

May 23, 2009 | 2005 Chevrolet Silverado 2500HD 2WD

1 Answer

Signal light stop working on a 1997 gmc sonona pickup trunk


Check the fuses in the fuse box, if all are good, replace the signal flasher.

Hope this is of some help.
Ed

May 07, 2009 | 1997 GMC Sonoma

2 Answers

Brake light


check all fuses some vehicls now a days have seperate fuses for left and right sides

Feb 09, 2009 | 2000 Chevrolet S-10

4 Answers

Dash light and tail lights not working


The dash and tail lights are controled by the first "click" of the headlight switch found on the turn signal arm.

If the fuses are good, then your turn signal arm has failed.

First click is running lights (dash and outside marker lights), second is headlights.

The 1st position of the 2 position switch has contacts internally that have worn and no longer complete the circuit.

Replace the turn signal arm.

Dan

Jul 20, 2008 | 1998 Land Rover Discovery

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

35 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8516 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...