Question about 2000 Chrysler Cirrus

2 Answers

Am changing the inner tie rod on a 2000 cirrus with a 2.5 and cant figure out how to get old one off

Posted by on

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 127 Answers

To get the inner tie rod out you need an inner tie rod tool, it's a long tube that fits a 1/2 inch drive rachet and there's different size adaptors that go into the end of it to fit over the tie rod, find the right size put into tool, put over tie rod and brake it loose, reverse for installtion.

Posted on Nov 18, 2009

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chrysler Master
  • 6,826 Answers

They make a special tool,it is a long tube that slides over the inner tie rod,and the end has changable crows foot to fit your car.This tool is costly,it is not cheap.If you undue the clamp,and pull back the boot,you will see the nut.The outer tie rod and sleave has to come off.

Posted on Nov 18, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Inner tie rod removal with tool


One end of the tie rod is a left hand thread
make sure that you are turning it the right way

Apr 12, 2015 | 2005 Hyundai Tucson GLS

1 Answer

How to change tye-rods on 2000 cirrus


There are two tie rod ends on each side, an inner and an outer. Each one
requires a special tool to remove. When the new parts are installed, the vehicle must be aligned, which again requires special knowledge and tools. Unless you own an alignment rack, a lift, and all the special tools, you are not going to be able to do this yourself.

Apr 14, 2010 | 2000 Chrysler Cirrus

2 Answers

2000 LINCOLN LS - Outer tie rod removal assistance


Yes degreaser will not hurt it. The outer tie rod is retained only by one nut that connects it to the inner tie rod.Once you have this loosen just turn the outer tie rod to the left to remove it from the inner tie rod.

Feb 24, 2010 | 2000 Lincoln LS

1 Answer

How to change inner tie rod 2000 saturn sl


CHECK OUT THE INNER TIE ROD TOOL FROM (KD TOOLS IT WILL WORK ON ALMOST ANY RACK&PINION SYSTEM OUT THERE)

Feb 07, 2010 | 2000 Saturn SL

1 Answer

I need a suspension diagram that shows the Inner tie rods.


The inner tie rods are screwed into ends of the steering rack assembly.

Look at this diagram. #6 is the rubber boots and #7 is the shaft from the inner tie rods.


http://www.anubiscycle.com/fixya/2000-windstar-steering-gear.jpg

Jun 08, 2009 | 2000 Ford Windstar

1 Answer

How difficult to replace inner tie rod end on 06 silverado 2wd?


Not that hard, just spray the tie rod sleeve with WD40 night before and let it soak in. Remove the collier pin and and nut and hammer the old inner tie rod end out of the Track rod with a 5 pound sledge hammer. Remove the inner tie rod end from the sleeve and don't forget to mark the distance so you can place the new tie rod end at the same length. Reinstall the inner tie rod end to the Track rod and tighten the nut and replace the collier pin with a new one. Grease the fitting and go for a test drive, if the truck does not wonder then your good to go with out a alignment. Good luck and hope this helps, Note, make sure you have to right inner tie rod ends. Each side has different thread rotations.

Jun 03, 2009 | 2006 Chevrolet Silverado 1500 2WD

1 Answer

Need torque spec for 2000 Cirrus outer tie rod ends


45 Ft-lbs Tie-rod balljoint stud-to-steering knuckle nut, and 55 Ft-lbs Tie-rod (outer)- to- inner jam lock nut

Apr 04, 2009 | 2000 Chrysler Cirrus

Not finding what you are looking for?
2000 Chrysler Cirrus Logo

338 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7710 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...