Question about Cars & Trucks

1 Answer

Just had sears deliver kenmore top loading washing machine. It is very very unstable and moves around way more than any other machine I've had. Is there something worng with it?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 10,865 Answers

Hello. Chances are it is not level. There are leveling pads at floor level at all four corners. You can level it yourself or [what I recommend] call the store and complain. You paid for delivery and setup and they did an unacceptable job of it. Insist that they come back and do it correctly.

Posted on Nov 18, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What's your question?how do I put tread inside d bobbing to make it saw normal


take the bobbin out of the bobbin holder, load up the bobbin fully
place the bobbin in the holder and pull the thread around the edge of the holder until the thread hits a slot and goes down under a flat spring plate
leave about 6" free thread and put the holder back into the machine
tun the machine over by hand and the top thread will pick up the bobbin thread
pull the bobbin thread up and place both top and bottom threads out the back of the foot
leave about 8" as when the needle moves down the top thread will be pulled out of the needle if it is too short

Mar 13, 2016 | Cars & Trucks

1 Answer

Unstable RPM and not sure what's the cause of it.


Has to be something in the fuel delivery system. The more fuel you give the engine the faster it turns and vice versa so it has to be something in this area. Could the fuel pump be operating erratically and have erratic pressure - that could be it.

Aug 30, 2015 | Cars & Trucks

1 Answer

Need a owners manual for my kenmore elite high energy washing machine


You might want to repost this in the washing machine section, or contact Sears.

Jan 26, 2014 | Cars & Trucks

1 Answer

I have a Daewoo washing machine which I can not get level. According to my spirit level it is deal level. Then as soon as the machine goes into spin it flies all over the room. It shakes so much it has...


check that the rods holding the tub inside are connected properly and have not become undone or broken or the insulators are still in good condition. If the tub inside is not level then no amount of levelling on the outside will help. Also check the out of balance switch (normally combined with the lid switch) as the machine should switch off after around 6 revolutions of unbalance because as soon as the tub moves a small amount it trips this switch and shuts the machine down

Aug 17, 2013 | Daewoo Cars & Trucks

1 Answer

Pressure is over 100psi on p1&p2 and p2 never drops below 10 eventhough the agitator is off


I am not sure what you are asking?> This question is posted in the CAR and TRUCK Problems... Maybe you need to close the question and move it to the section for Washing Machines or Applicances....

Apr 08, 2013 | Cars & Trucks

1 Answer

ONCE I'VE GOT THE ALTERNATOR BELT OFF HOW DO I GET THE ALTERNATOR TO MOVE ENOUGH TO GET THE NEW BELT ON


There is a spring loaded belt tensioner, use a wrench to deflect it and reinstall the belt.

May 30, 2012 | 2004 Hyundai Elantra

1 Answer

I have front loading washing machine and I need to put the belt on. I can use some tips, ideas on how to get it on


MAKE SURE THE POWER TO THE MACHINE IS OFF , THEN MAKE SURE YOU HAVE THE RIGHT BELT, FIRST YOU NEED A RACHET SET THEN LOCATE THE BOLTS AT THE SIDES AND UNDER THE TOP COVER AT THE BACK REMOVE ALL BOLTS AND THEN THE BACK PANEL, YOU SHOULD SEE THE BELT AROUND THE DRUM PULLY AT THE BOTTOM OF BELT YOU SHOULD SEE THE DRIVE MOTOR LOOK FOR A TENSIONER IF ONE TURN UNTILL BELT IS LOOSE REPLACE NEW BELT AND MAKE SURE IT VIS TIGHT , GOOD LUCK .

Nov 22, 2009 | Cars & Trucks

1 Answer

Kenmore washing machine went off balance now won't agitate or spin is there a reset button. I hear the belts going around they are high pitched.


no there is no reset button.When you say off balance im thinking of a machine jumping around the floor if this is the case then something has come loose or the balance block has broken inside your machine.adrian;;;;

Nov 11, 2009 | Cars & Trucks

1 Answer

My washing machine basin on a Whirlpool top has come loose.


Hello, down the center of the agitator there is a nut. You need a very long socket shaft to get to it, tighten this and it shold solve your problem. I hope this helps.

Nov 05, 2009 | Cars & Trucks

2 Answers

I have a C Class 230, 2007 with 27K miles. Owned


Let me understand that the problem is intermittent and engine is cranking but not started. For that being said, there are 2 main things to check.
1-The start is not on since there is not fuel delivered to the Fuel distribution. Fuel pump is controlled by the pump relay. But the pump relay is activated by the a fuel pump control module which is an electronics integrated module. This is the one gives unstable condition.
2- The start is not on since there is no electric signal to deliver to the primary coil. And this one is controlled by the ignition module. This is an integrated electronic module can give unstable condition.
The last thing to check is the Crank shaft sensor condition since it has to give the signal for the above 2 things to work. Good luck

Sep 04, 2009 | 2007 Mercedes-Benz C-Class

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

35 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...