Question about 1993 Land Rover Defender

2 Answers

How do you change a series 3 landrover fronf crank seal ?

Posted by on

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,486 Answers

Remove bottom pully and the you can see the oil seal hook it out and replace with care.Make sure its fitted flush.

Posted on Nov 18, 2009

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 1,586 Answers

The entire timing belt assembly has to be removed, plus the crank sprocket for the belt, and the seal is behind there. If you're not an experienced mechanic, this is NOT a recommended do-it-yourself job - the components that have to come off are critical, as is the setup of the engine before you remove them, and there are idiosyncrasies to each vehicle that make the job tricky unless you're intimately familiar with the car.

Posted on Nov 18, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Change oil on landrover td5


Sounds like maybe you Clutch is bad.

Jun 21, 2014 | 2000 Land Rover Discovery

1 Answer

Torque settings


I need the torque setting on the crank pully of my Landrover Defender 110 300 series engine

Jan 12, 2014 | Cars & Trucks

1 Answer

What is battery specification in my landrover freelander 2001


I don't show a listing for a 2001 in the US, a 2002 model takes a group 48 or group 91 series battery rated at 700 cold cranking amps.

Jul 29, 2012 | Cars & Trucks

1 Answer

HOW TO CHANGE A THERMOSTAT ON A 2002 LANDROVER DISCO


should be bottom right hand side take fan off to change

Feb 04, 2011 | 2002 Land Rover Discovery Series II

1 Answer

Landrover 2001 cuts out after 5 to 10 minutes (no spark,no fault lights/warning signals)After 30+ minutes car starts runs perfect for 5 to 10 and cuts out.Help needed, thanks


I just ran into a 2002 Discovery doing the same thing. What ended up being the fix was a cam sensor and crank sensor. That is about all I can say without more information. Hope this helps and best of luck.

Jun 04, 2010 | 2001 Land Rover Discovery Series II

1 Answer

My 2001 landrover discovery 2 will not turn over. I have a new starter and new battery. All the power items work but it wont turn over. Can u help?


check to make sure all fuse and relays are good. check the crank position sensor an the map sensor, make sure your getting 12v at the battery

Jul 31, 2009 | 2001 Land Rover Discovery Series II

1 Answer

1999 lexus es300 how to find cylinder no.3 and 4 ?


the front bank is bank 2, the rear one is bank one. The cylinders go from the timing belt side to the right. So 3 is the middle on the back bank, and four is the middle cylinder on the front bank. They are both in the middle so just replace them.

Jul 31, 2009 | 1999 Lexus ES 300

1 Answer

Describe your 2005 Chrysler Town & Country Problem HOW DIFFICULT IS IT TO CHANGE FRONT CRANK SEAL?


it's not too bad to change, you will need a special tool to remove the crank pully, it looks like a 3 jaw puller and once you get that off the seal is right behind it. Make sure to clean the crank pully shaft that goes through the seal with a piece of emery cloth to prevent leakage and coat it with either transmission assembly lube or a small amount of motor oil to prevent a dry start that can damage the seal again

Jul 23, 2009 | 2005 Chrysler Town & Country

1 Answer

Cannott open rear door of my landrover discovery 300 series


take off the logo on the rear door and spray some wd40 into the system.

Apr 07, 2009 | 2003 Land Rover Discovery

2 Answers

Overheating Leaking coolant completely out overnight Land Rover


sounds like a freeze plug, when the motor is warm the metal expands and its seals itself, when it cools over night it leaks..

let them redo the test on a cold motor

Jan 08, 2009 | 1997 Chevrolet Venture

Not finding what you are looking for?
1993 Land Rover Defender Logo

101 people viewed this question

Ask a Question

Usually answered in minutes!

Top Land Rover Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

yadayada
yadayada

Level 3 Expert

75051 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7726 Answers

Are you a Land Rover Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...