Question about 1998 Nissan Altima

1 Answer

How do I get the front cover off to change the timing chain?

I have removed all the bolts but it will not budge any solutions?

Posted by on

  • SuibeDude230 May 11, 2010

    Could you clarify which cover you are having trouble with?

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Remove the oil pan and drop the housing and remove more bolts then drop the cover down.

Posted on Nov 20, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Change timing belt


timing belt? on a Jeep? 05 wrangler
what engine is this>?
ah the 2.4L
front cover
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Remove the crankshaft vibration damper.
  3. Remove the generator drive belt tensioner assembly.
  4. Remove the timing belt front cover bolts, and remove the covers.


rear cover
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Remove the front covers.
  3. Remove the timing belt.
  4. Hold the camshaft sprocket with Special Tool 6847, or equivalent, while removing the center bolt.
  5. Remove the timing belt idler pulley.
  6. Remove the rear cover fasteners and remove the cover from engine.

Apr 04, 2014 | 2005 Jeep Wrangler

1 Answer

I replaced the right side head on my 2001 mustang gt and i need to know how to set up the timming so it will run right


Hi, this engine user copper links on the chain align the copper links with the marks shown on the diagram below. Please let me know if you have more questions, and thanks for using FixYa.

To install:
  1. Compress the timing chain tensioner plunger in a soft jaw vise and install a retaining clip to hold the plunger in place.
  2. Remove the tensioner.
  3. If the copper links are not visible on the timing chains, mark one link on each end of the chain.
  4. Install the left and right timing chain guides and tighten the bolts to 89 inch lbs. (10 Nm).
  5. Position the lower end of the left timing chain on the crankshaft sprocket, aligning the copper link with the timing mark on the outer flange of the crankshaft sprocket.
  6. Position the timing chain on the left camshaft sprocket with the camshaft sprocket timing mark aligned with the copper link.
  7. Position the left timing chain tensioner arm on the dowel pin and install the timing chain tensioner. Tighten the bolts to 18 ft. lbs. (25 Nm).
  8. Remove the retaining clip from the tensioner plunger.
  9. Position the lower end of the right timing chain on the crankshaft sprocket, aligning the copper link with the timing mark on the outer flange of the crankshaft sprocket.
  10. Position the timing chain on the right camshaft sprocket with the camshaft sprocket timing mark aligned with the copper link.
  11. Position the left timing chain tensioner arm on the dowel pin and install the timing chain tensioner. Tighten the bolts to 18 ft. lbs. (25 Nm).
  12. Remove the retaining clip from the tensioner plunger.
  13. Ensure correct alignment of all timing chain links and sprocket timing marks.
  14. Install the camshaft roller followers and tighten the camshaft sprocket bolts. See the procedure under Camshaft.
  15. Install the crankshaft sensor ring on the crankshaft.
    jturcotte_2085.gif

    Fig. Timing chain link and sprocket timing mark alignment-4.6L engine

  16. Apply sealant to the front cover mating surface as shown.
    jturcotte_2086.gif

    Fig. Sealant application to the front cover mating surface-4.6L engine

  17. Install a new gasket on the front cover, then install the front cover and hand tighten the bolts.
  18. Tighten the front cover bolts in the sequence shown to 18 ft. lbs. (25 Nm).
  19. Tighten the front cover-to-oil pan bolts in the sequence shown to 15 ft. lbs. (20 Nm), plus an additional 60 degrees
    jturcotte_2087.gif

    Fig. Front cover bolt tightening sequence-4.6L engine

    jturcotte_2088.gif

    Fig. Front cover-to-oil pan bolt tightening sequence-4.6L engine

  20. Lubricate the engine front cover and oil seal lip with clean engine oil and install the seal using a seal installer.
  21. Apply sealant to the Woodruff key slot in the crankshaft pulley, then press on the crankshaft damper.
  22. Tighten the crankshaft damper as follows:
    1. Step 1: 66 ft. lbs. (90 Nm).
    2. Step 2: Loosen the bolt one full turn.
    3. Step 3: 37 ft. lbs. (50 Nm).
    4. Step 4: 90 degrees.

  23. Connect the crankshaft position sensor connector.
  24. Install the power steering pump and tighten the bolts to 18 ft. lbs. (25 Nm).
  25. Install the wiring harness retainer to the power steering stud bolt.
  26. Install the power steering pump pulley shield.
  27. Install the water pump pulley.
  28. Install the J bracket to the engine front cover stud bolt.
  29. Install both left and right camshaft position sensor connectors.
  30. Install both left and right radio interference capacitors.
  31. Connect the hoses from the coolant crossover.
  32. Install the valve covers. See the procedure under Cylinder Head.
  33. Install the right side idler pulley.
  34. Install the accessory drive belt.
  35. Install the coolant degas bottle.
  36. Connect the negative battery cable.
  37. Fill the crankcase with clean engine oil.
  38. Start the engine. Check for leaks and proper operation.

Aug 14, 2011 | Ford Mustang Cars & Trucks

1 Answer

How do u set timing on it? 1.8 engine


Installation
Install crankshaft sprocket on crankshaft.
Make sure mating marks on crankshaft sprocket face front of engine.

Position crankshaft so that No. 1 piston is at TDC and crankshaft key is at 12 o'clock.

Install slack side timing chain guide and timing chain tension guide.

Install timing chain on crankshaft sprocket.
Set timing chain by aligning its mating mark with that on the crankshaft sprocket.
Make sure sprocket's mating mark faces engine front.

Install camshaft sprockets.
Set timing chain by aligning mating marks with those of camshaft sprockets.

Install camshaft sprocket bolts to correct torque.
Apply new engine oil to bolt threads and seat surface.

Install chain tensioner.
Before installing chain tensioner, insert a suitable pin into pin hole of chain tensioner.
After installing chain tensioner, remove the pin.
Install timing chain guide.

Install O-rings to cylinder block.

Before installing front cover, remove all traces of RTV silicone sealant from mating surface using a scraper.
Also remove traces of RTV silicone sealant from mating surface of cylinder block.

Apply a continuous bead of Genuine RTV Silicone Sealant or equivalent to mating surface of front cover. Refer to RECOMMENDED CHEMICAL PRODUCTS AND SEALANTS .
Check alignment of mating marks on chain and crankshaft sprocket.
Align oil drive spacer with oil pump.
Place timing chain to the side of chain guide. This prevents the chain from making contact with water seal area of front cover.

Install front cover.

Make sure two O-rings are present.

Be careful not to damage oil seal when installing front cover.
Install cylinder head bolts at engine front side as shown in Fig. 55.
Tightening procedure:
Tighten bolts (1 - 4): 6.3-8.3 N.m (0.64-0.85 kg.m, 55.8-73.5 in.lb).

Install oil pump drive spacer.
Install water pump and water pump pulley. Refer to REMOVAL AND INSTALLATION .
Install idler pulley and bracket.

Install RH engine mounting bracket

Install RH engine mounting.
Install oil pan. Refer to INSTALLATION.
Install crankshaft pulley.
Remove ring gear stopper.
Install starter motor.
Install cylinder head front cover.
Apply RTV silicone sealant to cylinder head front cover.
Use Genuine RTV Silicone Sealant or equivalent. Refer to RECOMMENDED CHEMICAL PRODUCTS AND SEALANTS .

Install Camshaft Position Sensor (PHASE).

Before installing rocker cover, apply a bead of Genuine RTV Silicone Sealant or equivalent, to mating surface of cylinder head as shown in .

Install rocker cover gasket into rocker cover.
Install rocker cover and tighten in numerical order as shown in
Install spark plugs.
Install ignition coils.
Install front exhaust tube.
Install front/right-side splash undercover.
Install front RH wheel.
Install drive belts.
Adjusting drive belt deflection..

Nov 29, 2010 | 2002 Nissan Sentra

1 Answer

How do you remove toyota timeing chain


Timing Chain and Gears Removal & Installation To Remove:
toy_car_18_gen-p-s-mnts-cvrs-exhst_xp.gif

Except XRS toy_car_18_eng_cmpnts+oil_pmp_loc_1zz-fe_xp.gif

XRS toy_car_18_eng_cmpnts+oil_pmp_loc_2zz-ge_xp.gif

toy_car_18_gen-p-s-mnts-cvrs-exhst_xp.gif

  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Drain cooling system.
  3. Remove the upper front fender apron insulator.
  4. Remove the upper radiator support insulator.
  5. Remove the right front wheel and tire assembly.
  6. Remove the right lower splash shield.
  7. Remove the drive belt and alternator.
  8. Remove the air switching valve (XRS)
  9. Remove the power steering oil pressure switch connector.
  10. Remove the 2 power steering mounting nuts and through bolts. Remove the steering pump from the engine. Secure the steering pump to the cowl toy_car_15_wood_block_on_jack.gif

  11. Raise and support the engine with floor a jack. toy_car_18_eng_rh_mntng_inslt_blts.gif

  12. Remove the right engine mount. toy_car_18_eng_cylndr_hd_cvr_blts.gif

  13. Remove the 2 nuts, 2 clips and the cylinder head shield (except XRS).
  14. Remove the 4 ignition coils.
  15. Remove the 2 ventilation hoses from the cylinder head valve cover.
  16. Remove the 9 bolts, 2 seal washers, 2 nuts, cylinder head cover and gasket (except XRS). XRS toy_car_18_eng_cylndr_hd_cvr_blts_2zz-g.gif

  17. Remove the 4 bolts and the cylinder head shield (XRS).
  18. Remove the 2 nuts, bolt and remove the ventilation hose from the ventilation pipe (XRS). XRS toy_car_18_eng_cylndr_hd_cvr_ventl_hs-pp.gif

  19. Remove the Ventilation pipe and gasket (XRS).
  20. Remove the 9 bolts, wire harness protector. Remove the cylinder head cover and gasket (XRS).
  21. Remove the O-ring from the cylinder head cover (XRS)
  22. Turn the crankshaft pulley and align its groove with timing mark "0" on the timing chain cover. toy_car_18_eng_tmng_mark.gif

  23. Ensure that the marks on the camshaft timing sprockets are in straight line on the timing chain cover surface as shown. toy_car_18_eng_tmng_point_marks.gif

  24. If not turn the crankshaft 1 revolution (360°) and align the marks as above.
  25. Remove the crankshaft pulley toy_car_18_eng_rmv_crnk_sft_pos_snsr_blts.gif

  26. Remove the 2 mounting bolts and remove the crankshaft position sensor.
  27. Remove the mounting bolt, nut and the drive belt tensioner.
  28. Remove the right engine mount bracket.
  29. Remove the front exhaust pipe (XRS).
  30. Remove the Exhaust manifold brace (XRS).
  31. Remove the Exhaust manifold (XRS) toy_car_18_eng_tmng_chn_tnsnr_blts.gif

  32. Remove the 2 mounting nuts and remove the chain tensioner.
  33. Remove the water pump. Except XRS toy_car_18_eng_tmng_chn_cvr_blts_1zz-fe.gif

    XRS toy_car_18_eng_tmng_chn_cvr_blts_2zz-ge.gif

  34. Remove the 11 mounting bolts and nut (except XRS).
  35. Remove the 12 bolts (XRS).
  36. Remove the stud bolt.
  37. Remove the timing chain cover and 2 gaskets.
  38. Remove the crank sensor plate.
  39. Remove the timing chain tensioner slipper mounting bolt. Remove the tensioner slipper. toy_car_18_eng_tmng_chn_sprkt.gif

    Note: If the crankshaft timing sprocket cannot be removed by hand, use 2 screwdrivers. Position shop rags as shown to prevent damage.
  40. Remove the timing chain and crankshaft timing sprocket.
  41. Remove the 2 chain vibration damper mounting bolts. Remove the vibration damper toy_car_18_eng_tmng_cntrl_assy.gif

  42. Hold the camshaft hexagonal section with a wrench. Remove the sprocket mounting bolt.
  43. Remove the valve timing controller assembly and timing sprocket.
Note: Be careful not to damage the cylinder head and valve lifter with the wrench.
Do not disassemble the valve timing controller assembly.

Oct 19, 2010 | 2005 Toyota Corolla

1 Answer

Can i remove the timing chain tensioner from the top of the motor on a 2000 cavalier 2.2l or is that only with a dual cam?


Hi Friend:

Your Timing Chain Tensioner is located in the Lower Front of your engine.

#1) you'll have to disconnect your negative Battery cable.

#2) Remove the Top Engine cover to give you better access to the Front of Engine.

#3) Then you'll need to remove your alternator and with wiring attached put it off to the Side you might have to tie it with a wire to secure it.

#4) then you'll need to remove your Power Steering Leave the Lines on it and Put it to the sideas well , Tie off if necessary.

#5) then Jack up the front of your car,make sure you Put Good Stands under the car to keep it secure.while you work under it.

#6) then remove the TWO front Oil Pan Bolts Only the very 2-Front ones.

#7) Then directly above the Oil pan front of the Engine you'll see your Crank Shaft Pulley Remove it, You will need a Puller to Remove it.then the Timing Chain Cover, There are Several bolts Holding it on to the front of the Engine.

#8) Remove ALL the Bolts on Timing over, then Take cover Off,It could be a Little Stubborn ,if All bolts are out for sure, Take a Small plastic mallet and Tap the Cover Easily,until it comes off.

#9) Now before you remove anything else there is a Timing Mark on the Cam Shaft and one on the Crank Shaft,NOTE: BESURE you line them marks up,The Cam Shaft Mark should be pointing Straight Down--And the Crankshaft Mark needs to be Pointing Straight up.and Lined up with the Top Timing Mark.If the are Not

NOTE: Rotate the Engine by Hand Turning the Sprockets until they are LINED Up.

Then Take off the Top Cam Shaft Mounting Bolts,then Pull Sproket and timing Chain at the Same Time.

Then Loosen the Chain Tensioner Bolt with out taking it ALL the Way OUT. then remove your Chain Tensioner.

If your this far i Recommend that you Replace The Timing Chain,Cam Sproket and Crankshaft Sproket as well.

If not the Install your new Chain Tensioner,And Just Simply Reverse the Un-Install Directions.To Put All back Together.

Do Replace the Timing Cover Seal. Using Proper Seal Remover and Installer.

Also before you put your Timing cover back on CLEAN the Surfaces of the Engine and the Cover.And Use a Gasket Sealer and Mount to Block ==Lining Up ALL your Timing Cover Bolt Holes. Let it set a Short time a Few Minutes at Least. To prevent Slipping when installing your Timing Case Cover.

1- Last Thing Torque your Timing Chain Tensioner at 89 Inch Pounds.Which rewuires a Torque Wrench.

And Torque ALL your Timing Cover Bolts at 97 Inch Pounds.Do NOT Over Tighten You'll Strip them.

MAKE Sure the Timing Marks are Still lined up.

This will get your Timing Chain Tensioner Replaced. Thanks for using FixYa From: d_hubbs

Aug 17, 2010 | 2000 Chevrolet Cavalier

1 Answer

My 2001 jeep grand Cherokee will not start don?t know why no codes are coming up put new cam sen, crank sen, coil pack, new ecu, new coolant temp sen, it turns over but will not run has injector pulse and...


Timing Chain, Sprockets, Front Cover and Seal REMOVAL & INSTALLATION 2.5L and 4.0L Engines
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Remove or disconnect the following:
    • Negative battery cable
    • Accessory drive belt
    • Cooling fan and shroud
    • Crankshaft damper
    • Front crankshaft seal
    • Accessory brackets
    • Front cover
    • Oil slinger
  3. Rotate the crankshaft so that the timing marks are aligned. Fig. 1: Timing chain alignment marks — 2.5L and 4.0L engines 7924pg20.gif

  4. Remove the timing chain and sprockets. To install:
  5. For 2.5L engines, turn the timing chain tensioner lever to the unlock (down) position. Pull the tensioner block toward the tensioner lever to compress the spring. Hold the block and turn the tensioner lever to the lock (up) position. Fig. 2: Timing chain tensioner — 2.5L engines 7924pg19.gif

  6. Install the timing chain and sprockets with the timing marks aligned. Tighten the camshaft sprocket bolt to 80 ft. lbs. (108 Nm) for 2.5L engines or to 50 ft. lbs. (68 Nm) for 4.0L engines.
  7. For 2.5L engines, release the timing chain tensioner.
  8. Install or connect the following:
    • Oil slinger
    • New front crankshaft seal to the front cover
    • Front cover, using a new gasket
    • Timing Case Cover Alignment and Seal Installation Tool 6139 in the crankshaft opening to center the front cover Fig. 3: Timing Case Cover Alignment and Seal Installation Tool 6139 — 2.5L and 4.0L engines 7924pg21.gif

  9. Tighten the front cover bolts as follows:
    1. Step 1: Cover-to-block 1⁄4 inch bolts to 60 inch lbs. (7 Nm)
    2. Step 2: Cover-to-block 5⁄16 inch bolts to 16 ft. lbs. (22 Nm)
    3. Step 3: Oil pan-to-cover 1⁄4 inch bolts to 85 inch lbs. (9.5 Nm)
    4. Step 4: Oil pan-to-cover 5⁄16 inch bolts to 11 ft. lbs. (15 Nm)
  10. Install or connect the following:
    • Accessory brackets
    • Crankshaft damper. Tighten the bolt to 80 ft. lbs. (108 Nm).
    • Cooling fan and shroud
    • Accessory drive belt
    • Negative battery cable
  11. Start the engine and check for leaks.

Jul 30, 2010 | 2001 Jeep Grand Cherokee

1 Answer

Change oil pump from engine


THE 3.0 ENGINE YOU HAVE TO REMOVE THE UPPER INTAKE MANIFOLD .REMOVE VALVE COVERS REMOVE ACESSORY DRIVE BELT.REMOVE THE POWER STEERING PUMP.REMOVE ALTERNATOR REMOVE WATER PUMP .REMOVE AC COMPRESSOR AND BRACKET .REMOVE CRANKSHAFT PULLEY REMOVE OIL PAN REMOVE OIL PUMP SCREEN AND THE TUBE REMOVE FRONT COVER REMOVE TIMING CHAINS REMOVE CRANKSHAFT TIMING GEARS REMOVE OIL PUMP.WHEN INSTALLING NEW OIL PUMP AND OIL PUMP SCREEN AND TUBE TORQUE BOTH 89 INCH POUNDS. THE 3.9 ENGINE REMOVE THE CRANKSHAFT PULLEY REMOVE FRONT COVER REMOVE THE PRIMARY TIMING CHAINS REMOVE OIL PUMP MOUNTING BOLTS REMOVE OIL PUMP.INSTALLING NEW OIL PUMP TORQUE BOLTS TO 53 INCH POUNDS. WARNING YOU NEED A REPAIR MANUAL IN ORDER TO RELINE TIMING MARKS ON CAMSHAFTS AND CRANKSHAFT.

Apr 22, 2010 | 1997 Lincoln Continental

1 Answer

Serpentine belt


5729dde.gif
This is a job for an experienced technician. Probably about a $300 job. Maybe more.

Here is procedure for 1996:

Removal
  1. Drain the cooling system. Refer to Section 03-03 for the procedure.
  1. Disconnect the battery ground cable (14301).
  1. Remove the generator drive belt, water pump and power steering pump drive belt, and the A/C compressor drive belt (if equipped). Refer to Section 03-05 for the removal procedure.
  1. If equipped, remove the three A/C compressor drive belt idler pulley bolts and the A/C compressor drive belt idler pulley.
  1. Remove the upper radiator hose bracket bolt.
  1. Loosen the two upper radiator hose clamps and remove the radiator hose bracket bolt. Remove the upper radiator hose (8260) and the upper radiator hose bracket from the vehicle.
  1. Remove the water bypass hose (8597) from between the thermostat housing and the water hose connection (8592).
  1. Remove the main wiring harness from the upper engine front cover (6019).
  1. Remove the eight upper engine front cover bolts and the upper engine front cover.
  1. Raise and support the vehicle.
  1. Remove the RH front wheel and tire assembly.
  1. Remove the four RH outer engine and transmission splash shield bolts and two screws and remove the RH outer engine and transmission splash shield (6775).
  1. Use Strap Wrench D85L-6000-A or equivalent to hold the water pump pulley (8509) while removing the four water pump pulley bolts.
  1. Remove the water pump pulley from the water pump (8501).
  1. Remove the crankshaft pulley (6312). Refer to the procedure in this section.
  1. Remove the five lower engine front cover bolts and the lower engine front cover.
  2. Ensure that the timing marks between the crankshaft sprocket (6306) and the oil pump housing line up.
2acab54.gif
18. NOTE: The directional arrow is necessary to ensure that the timing chain/belt (6268) can be reinstalled in the same direction.

If the timing chain/belt is to be reused, mark the direction of rotation on the timing chain/belt.

19. Loosen the timing chain/belt tensioner nut.

  1. Remove the timing chain/belt.
Installation
NOTE: Ensure that the timing marks on the camshaft sprockets (6256) and the seal plate are properly aligned. Ensure that the timing marks on the crankshaft sprocket and the oil pump housing are still aligned.



stv~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Pay special attention to the tooth shape of the timing belt. The current timing belts are not interchangeable with the timing belts from the 1993 model year. The 1993 model year uses a square or trapezoidal tooth timing belt while the current model year uses a rounded tooth design. The design change was made to extend the service life of the timing belt from 60,000 miles for the square or trapezoidal toothed belt to 105,000 miles for the rounded tooth belt. If the proper timing belt is not used, the customer may complain of a "whining" noise coming from the engine compartment. If the camshaft sprocket has a square cut in the valley of the gear tooth, it will require a square or trapezoidal tooth timing belt. If the camshaft sprocket has a rounded cut in the valley of the gear tooth, it will require a rounded tooth timing belt.
NOTE: If a new timing chain/belt is to be installed, make sure that the arrow is pointing away from the engine. If a timing chain/belt is to be reused, make sure that the directional arrow that was marked during disassembly is facing the correct direction.

NOTE: A new timing chain/belt has three white timing marks that indicate the correct timing positions of the camshafts and the crankshaft. These marks will help ensure that the engine (6007) is timed properly. When the engine is properly timed each white timing mark on the timing chain/belt will be aligned with the corresponding camshaft and crankshaft timing mark on the sprocket. Because the white timing marks are not evenly spaced you will need to refer to the following illustration for proper timing chain/belt placement. There should be 40 timing belt teeth between the timing marks of the front and rear camshaft sprockets and 43 teeth between the timing mark on the front camshaft sprocket and the timing mark on the crankshaft sprocket.

NOTE: Verify that the camshaft timing marks are aligned with the timing marks on the seal plate, and that the crankshaft sprocket timing mark is aligned with the timing mark on the oil pump (6600).

Install the timing chain/belt starting at the crankshaft sprocket and moving around to the camshaft sprockets following a counterclockwise path. Do not allow any slack in the timing chain/belt between the timing sprockets. After all of the timing marks are matched up with the timing chain/belt installed, slip the timing chain/belt onto the timing chain/belt tensioner.

  1. While holding the timing chain/belt tensioner with an Allen wrench, loosen the timing chain/belt tensioner nut.
  1. Allow the timing chain/belt tensioner to put pressure on the timing chain/belt.
  1. Use an Allen wrench to turn the timing chain/belt tensioner 70-80 degrees clockwise and tighten the timing chain/belt tensioner nut to 43-58 Nm (32-43 lb-ft).

    1. Rotate the crankshaft (6303) clockwise twice and align the No. 1 piston to Top Dead Center (TDC) on its compression stroke.
    1. Apply 98N (22 lbs) of force on the timing chain/belt between the rear camshaft sprocket and the timing chain/belt tensioner.
    2. NOTE: An assistant may be needed to adjust the timing chain/belt.

      While holding the timing chain/belt tensioner steady with an Allen wrench, loosen the timing chain/belt tensioner nut. Remove the Allen wrench and adjust the timing chain/belt tensioner as follows:
      1. Install a 0.35mm (0.0138 inch) thick and 12.7mm (0.500 inch) wide feeler gauge as shown.

  1. Turn the crankshaft clockwise to position the feeler gauge between the timing chain/belt tensioner and the timing chain/belt

  1. Tighten the timing chain/belt tensioner nut to 43-58 Nm (32-43 lb-ft).
  1. Turn the crankshaft clockwise to remove the feeler gauge from between the timing chain/belt tensioner and the timing chain/belt.
  1. Rotate the crankshaft clockwise twice and align the No. 1 piston to TDC on its compression stroke.
  1. Apply 98N (22 lbs) of force on the timing chain/belt between the rear and front camshaft sprocket.
    1. Measure the timing chain/belt deflection. Timing chain/belt deflection should be between 13-15mm (0.51-0.59 inch). If timing chain/belt deflection is not within specification, repeat steps 3-11. If the timing chain/belt cannot be adjusted to within specification, the timing chain/belt will have to be replaced.
    1. Position the lower engine front cover and install the five lower engine front cover bolts. Tighten the five lower engine front cover bolts to 3-5 Nm (27-44 lb-in).
    1. Install the outer timing chain/belt guide and the crankshaft pulley. Refer to the procedure in this section.
    1. Position the water pump pulley on the water pump and install the four water pump pulley bolts
    1. Use Strap Wrench D85L-6000-A or equivalent to hold the water pump pulley, and tighten the four water pump pulley bolts to 16-21 Nm (12-15 lb-ft).
    1. Position the RH outer engine and transmission splash shield and install the four RH outer engine and transmission splash shield bolts and two screws.
    1. Install the RH front wheel and tire assembly. Tighten the lug nuts (1012) to 98-118 Nm (72-87 lb-ft).



Feb 14, 2009 | 1993 Mercury Villager

Not finding what you are looking for?
1998 Nissan Altima Logo

153 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

713 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...