Question about 1998 Jaguar XK8

Open Question

Hazard warning lights won't go off. have tried switch and nothing happens. Help!!!!!!!!!!

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hi I'm driving Toyota yaris 2009 hatchback when i indicate it makes hazards please help


Make sure your actual hazard switch is off and try again. If you still have issues the problem is probably in the hazard switch.09 yaris hazard switch 2016 Toyota Yaris Hazard Warning Switch Lock switch Steering Part...

Feb 20, 2017 | Toyota Cars & Trucks

1 Answer

Where is the signal light relay that makes signal lights flash located on 2000 ols intrigue 3.5 liter


Important: The hazard warning switch includes the turn signal and hazard warning flashers.
Removal Procedure
Remove the center air deflector. Refer to Instrument Panel Center Air Outlet Deflector Replacement .
Squeeze the retainer on the backside of hazard warning and cruise control switch.
Pull the hazard warning and cruise control switch from the retainer in the instrument panel.
Disconnect the electrical connectors from the hazard warning and cruise control switch.
Remove the hazard warning and cruise control switch from instrument panel.
Remove the hazard warning and cruise control switch bezel from the instrument panel trim pad by using a small flat-bladed tool to the release retainers.
Remove the radio. Refer to Radio Replacement in Entertainment.
Reach through the radio opening and push the retainers up towards the roof of the vehicle. When the retainers release, slide the instrument panel (I/P) center air outlet deflector out of the I/P opening
Remove the air outlet deflector
Remove the instrument panel accessory trim plate. Refer to Instrument Panel Accessory Trim Plate Replacement in Instrument Panel, Gauges, and Console.
Remove the bolts from the radio.
Pull the radio toward you.
Remove the front floor console trim plate. Refer to Front Floor Console Trim Plate Replacement .
Pull the instrument panel (IP) accessory trim plate away from the IP trim pad.
Disconnect the IP harness seat heater leads, if equipped.
Remove the seat heater switches from the IP accessory trim plate, if equipped.
Remove the IP accessory trim plate.

Nov 09, 2016 | Cars & Trucks

1 Answer

I have an 02 kia sportage. my signal lights come on but dont blink outside. no lights for the signal lights come on on the dash at all. also, no hazard lights.


If the 15A HAZARD fuse in the passenger compartment fuse box is OK, power is getting to the hazard function of the flasher unit. Pressing the hzard switch should cause the hazard lights to flash. HOWEVER, there is an electronic time and warning indication system module connected to to the hazard switch lead and that may be affecting things. If the 10A TURN fuse is OK, power is applied to the turn switch (with the engine in START or RUN) and you state you can select a right or left turn. HOWEVER, the RED/WHT and RED/BLU outputs from the flasher unit connect directly to the front and rear turn lamps and the instrument cluster turn indicators so you are not getting any flasher output. Again, that electronic time & warning indication system module could be affecting things

Oct 26, 2012 | Cars & Trucks

1 Answer

I changed the fuse as the turn lights and hazard lights were not working but all other light including brake and interior worked. Now the hazard light stays on and I cannot turn it off. can you Help p


if your hazard lights stay on, you may have a problem with the hazard switch on your stearing collum. try moving it back & forth several times, eg. on, off, on, off always ending @ off & see if that works. they do get sticky @ times. your brake lights will work but your turn signals won't work properly with the hazard switch turned on. let me know if problem persists & will see if i can help you more. good luck.

Nov 24, 2011 | 1999 Saab 9-5

3 Answers

No break lights or hazard lights or no turn signals


first check all fuses then under hood check all fusible links

Aug 12, 2009 | 2000 Pontiac Grand Am GT

2 Answers

No hazard lights


Check the hazard switch and the connector to hazard switch see if u have the power and earth to hazard switch if there is power and earth to switch then replace ur hazard switch its faulty but if there is no power and earth to switch then it has whirring problem

Jun 16, 2009 | 1997 Mitsubishi Mirage

1 Answer

The turn on lights does not flash


Check out this recall below:
Bulletin No.: 04098A

SPECIAL POLICY
Subject:
04098 - Special Policy Adjustment - Turn Signal/Hazard Warning Flashers 

Condition
Some customers of 1999-2002 Chevrolet Malibu, Oldsmobile Alero, Pontiac Grand Am, and 1999 Oldsmobile Cutlass may have turn signal/hazard flashers that become inoperative.

Special Policy Adjustment
This special policy covers the condition described above for a period of 10 years or 150,000 miles (240,000 km), whichever occurs first, from the date the vehicle was originally placed in service, regardless of ownership. The repairs will be made at no charge to the customer.

Good luck and hope this helps:
HAZARD WARNING SWITCH REPLACEMENT - ON VEHICLE 
REMOVAL PROCEDURE 

Remove the center air louver deflector. Refer to Air Deflector Louver Replacement - Center Vent. 
Remove the instrument panel cluster. 
Remove the hazard warning switch bezel from the instrument panel using a small-flat bladed tool to release the retainers.
Remove the left side bolt from the hazard warning switch through the instrument panel cluster pocket Remove the right side and center lower bolts from the hazard warning switch through the center air louver deflector pocket.
Reposition the hazard warning switch from the instrument panel to access the electrical connector. 
Disconnect the electrical connectors from the hazard warning switch. 
Remove the hazard warning switch from instrument panel. 

INSTALLATION PROCEDURE
Connect the electrical connectors to the hazard warning switch.
Position the hazard warning switch to the mounting points in the instrument panel. NOTE: Refer to Fastener Notice in Service Precautions.
Install the left side bolt to the hazard warning switch through the instrument panel cluster pocket. Tighten Tighten the left side hazard warning switch bolt to 3 N.m (27 lb in) . 
Install the right side and center lower bolts to the hazard warning switch through the center air louver deflector pocket. Tighten Tighten the left side hazard warning switch bolt to 3 N.m (27 lb in) . 
Install the hazard warning switch bezel to the instrument panel pressing into place until fully seated. Install the instrument panel cluster. 
Install the center air louver deflector. Refer to Air Deflector Louver Replacement - Center Vent.

May 24, 2009 | 2000 Oldsmobile Alero

Not finding what you are looking for?
1998 Jaguar XK8 Logo

Related Topics:

175 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jaguar Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

yadayada
yadayada

Level 3 Expert

75197 Answers

SPEEDY CAR WORK SHOP...

Level 2 Expert

489 Answers

Are you a Jaguar Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...