Question about 2005 Dodge Durango

Open Question

One headlight stopped working. I installed a HID kit. I turned on the headlight witch to see if the light would work I heard a clicking noise, not shore were the noise was coming from. Turned off the headlights witch and plug in the HID bulb to the ballast kit. The HID kit came on and witched to high beam and it worked. Switched back to low beam and the HID kit didn?t come on, plug in the factory Headlight bulb and it still didn?t work. All the other light work but this one. Using a multi meter to test the voltage I have a voltage potential of 10.54Volts when the light was turned off on the low beam circuit. I feel like there is some kind of module that needs to be reset. Help

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 412 Answers

SOURCE: 2003 dodge ram deisel change fcm no change.still

sounds like fuseblock underhood is faulty..front control module is on fuseblock

Posted on May 22, 2009

  • 88 Answers

SOURCE: headlights not working

check fuses in under hood fuse box let me know i will at some diagrams for you hey vote for me ok

Posted on May 26, 2009

jmgldsmth
  • 1869 Answers

SOURCE: One of my Headlight not working during low beam

replace both headlight bulbs
each bulb has two filiments inside the bad bulb has a burned out filiment but, they should be replaced as a pair
and, do not touch the glass with your fingers
the oil from your fingers can cause the bulb to fail

Posted on May 29, 2009

  • 412 Answers

SOURCE: 02 dodge caravan headlights

SOUNDS LIKE INTEGRATED POWER MODULE(UNDERHOOD FUSEBLOCK)IS DEFECTIVE..ALSO CHECK FOR CORRODED TERMINALS IN CONNECTORS ON FUSEBLOCK..HAVE SEEN THIS BEFORE AND NEW FUSEBLOCK WAS NEEDED AND REPAIRED PROBLEM

Posted on May 31, 2009

  • 161 Answers

SOURCE: 2005 Dodge Caravan headlight stay dim when turned on

I belive there is a seperate module for the DRL controll. that may have gone out.

Posted on Jun 14, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replacing halo and hid lighting in an after market headlight


    Aftermarket Projector Headlight How To Replace HID ...

    store.ijdmtoy.com/Aftermarket-Projector-Headlight-HID-Installation.../5...
    Here are some quick tips and instructions on how to install an aftermarket HIDConversion kit into an aftermarket projector headlight assembly. ... Aftermarket projector headlights look almost like an OEM headlight with the exception of the wiring and design. You would need to remove ... images for Replacing halo and hid lighting in an ...

Nov 24, 2015 | 2000 Jeep Grand Cherokee

1 Answer

Hid headlights


( please add year and model type) you just need to change the module for the hids usually fitted to the light housing. they dont cost alot to replace. but converting back to normal lights you will need the the light bulb housing. these can be hard to find. as they just get chucked away. you can get hid kit if you want to change both lights they come with a manual on how to install them.

Mar 16, 2014 | Mini Cars & Trucks

1 Answer

Hid headlight on 2005 vw beetle won't work


For many European cars, you might need to add capacitor to ensure the HID working properly.

You will probably need this

CAN BUS Error Free HID Decoders Installing HID Conversion Kit

Jan 27, 2014 | Cars & Trucks

1 Answer

How do i switch the regular headlights of a 96 crown vic to hid lights


get on ebaymotors then click on the parts and accesories tab. after that type in the year make and model of your vehicle followed by hid headlight kit and out will come an enormous list of hid conversion kits that you can purchase for your vehicle!

Jan 07, 2013 | Cars & Trucks

1 Answer

99 Grand Cherokee headlights keep popping fuese


The circuit load is much higher with the HID lights, you need to rewire the headlights to a large gauge wire.

Jul 03, 2012 | 1999 Jeep Grand Cherokee

3 Answers

I replaced my main bulbs with hid xenon in my 98 range rover hse


First let me just explain something about putting HID bulbs in a reflector headlight, then I'll get to answering your question. High end cars use something called a projector with their HID bulbs and these projectors focus the light into patterns that won't blind other drivers with very perfect cutoffs (no light goes above a certain line). To retrofit a projector into your stock housing it takes a lot of work and careful measurements and thus a lot of time. But this is the only way to do a HID retrofit the right way.
Putting a HID kit into a reflector housing as you did, also makes light scatter everywhere, which creates many hotspots or high concentrations of light that make it much more difficult to see the road. Not only do HID kits in relfector housings make it more difficult to see, they are hugely illegal, and can/may get you pulled over and ticketed by a police officer. 
The best thing you could do insted of putting a HID kit in your relfector housing is to get higher wattage bulbs, OSRAM makes some great H4 overwattage bulbs. http://www.rallylights.com/SearchResult.aspx?CategoryID=6
If you purchase from rally lights (you need to purchase them in sets of two( I wouldn't go over 85/80 watt bulbs because it could melt your housing.)
Also make sure your headlights with stock bulbs are aligned correctly, most of the time this alone makes a huge difference as headlights droop over the years. 
If you are set on using your HID Kit illegally and blinding all other drivers on the road and willing to live with the risk of getting pulled over by any cop you run into. You will need to figure out how to trick ecu into thinking regular headlights are being used because its detecting the power being drawn for your HID lights to be a fault in the system that needs to be replaced. You can do this by wiring in a 55watt resistor to the circuit. 

May 18, 2009 | 1998 Land Rover Range Rover

2 Answers

Problem with hid on 2008 dodge ram 2500


Not too much amperage. HID lights use less amps. Duh. The circuit is showing a failure in the HID kit from not enough amps so it turns off. You need to add a resistor.

Apr 27, 2009 | Dodge Ram Pickup 2500 Cars & Trucks

3 Answers

Hid light not turning on


the part about the lights that won't turn on may be because there is a blown fuse or a broken relay which needs to be changed, the part about the hid lights there may be a short circuit somewhere.

Apr 03, 2009 | 2006 Mitsubishi Galant

1 Answer

Installing hid headlights in my 2003 denali


You can not bypass you drls. I just put a hid kit in my 97 yukon. You have to buy a wireing harness that hooks into your harness currently on your truck. The only way to shut you dlrs off is you e brake

Nov 30, 2008 | 2003 GMC Yukon Denali

Not finding what you are looking for?
2005 Dodge Durango Logo

Related Topics:

450 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7768 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...