Question about 2009 Hyundai Tucson

1 Answer

Gear stick vibration only in 3rd gear @ 2500 rpm on my new 2009 Tucson 2l any idea what causes this,as dealer says new "PART" needs to be fitted

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

My brand new 2009 Tucson has the same problem. My dealer said it needs a 3rd Gear Kit fitted.
They are on back order as a number of other Tucson's have the same problem. I may have to wait 3 months for the part.
My dealer has ordered 126 back order parts for this problem.


Posted on Jan 04, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I had new clutch fitted 3 weeks ago now the gear stick has gone loose and I only have 3rd and 4th gear


Sounds like one of the rods between the gear lever and gearbox has become detached. One rod transmits the forward-backward motion, the other left - right, with the "natural" bias keeping the lever in the 3rd / 4th gear plane - hence why you've only got 3rd and 4th gear.

You should have some guarantee from the company that fitted the clutch so contact them to sort it out.

Mar 14, 2015 | 2006 Peugeot 207 1.4

1 Answer

Kia cerato sticks on gear 3 but car drives normally for the first 15-20 mins


must be an internal gear problem take to a KIA dealer as they will probably know of a fault

Apr 09, 2014 | 2005 Kia Spectra

2 Answers

2009 toytoa tacoma 2.7 lt rear wheel drive shake on ideal while in gear


1st things first. What fault codes do you have in memory from the diagnostic port? Buy a code reader and check that.

Mar 17, 2014 | Toyota Tacoma Cars & Trucks

1 Answer

Vibration between 20-25 in 3rd gear and 28-32mph in 4th gear


did you replace the clutch plate as well as the clutch ? as not doing so it can be warped from the heat of old one burning out. also did you check the flywheel as any imperfections in the plate can cause clutch wobble.

Jul 21, 2017 | 2005 Hyundai Getz 1.3

1 Answer

Codes p0700,p0733,p0734 dodge caravan 1997


P0700 is a informative transmission code, about some problem there; the P0733 and P0734 is the specific problem there.
I would first try changing the fluid and filter. Although the fluid may look like it is brand new, with 100K on the fluid, I can assure you that even if those miles were all highway at steady speed and no load that the fluid has deteriorated and no longer lubricating the internal parts properly and that there is some debris in the ******.If codes return and shifting problems are still present, there is definite internal failure, possibly the pump or in the clutches.
DTC P0733The powertrain control module (PCM) uses the crankshaft position (CKP) sensor, input speed sensor (ISS) and output speed sensor (OSS) to determine engine speed, input shaft speed and output shaft speed. These sensor readings are used to determine the current gear ratio and RPM slip across the torque converter. The PCM uses this information from the sensors to determine if the commanded gear matches the actual gear. During normal driving conditions, the PCM will adapt main line pressure via the pressure control (PC) solenoid to prevent slipping and harsh shifts. Shift solenoid 3 is used to apply or release third gear clutch. The PCM controls 3rd gear by controlling the ground for shift solenoid 3. The PCM will turn the solenoid OFF, open the driver circuit, when 3rd gear is commanded On to apply 3rd clutch. Shift solenoid 3 is supplied ignition voltage from the fuel pump relay whenever the PCM commands the fuel pump relay ON. DTC P0733 sets when 3rd clutch still slips after the PCM has commanded high main line pressure.DTC Parameters
DTC P0733 will set if the PCM detects an incorrect actual 3rd gear ratio when 3rd gear is commanded On when:- The condition exists for longer than 3 seconds (2001)*- The condition exists for longer than 3 seconds, 1 minute is allowed to elapse, then condition exists again for longer than 3 seconds (2000)- The high main line pressure has been commanded- The transaxle is in a forward gear- The input speed is greater than 224 RPM- The vehicle speed is greater than 5 km/h (3 mph)- The speed noise parameter = NO- The steady state ratio fail counter equals 255 for an in-gear failure, or the shift fail counter is greater than 100 on a downshift or upshift to 3rd gear (128=0 or normal operation)DTC P0733 diagnostic runs continuously once the above conditions have been met.
DTC P0733 is a type A DTC for 2000, type B for 2001.**Applicable to vehicles built after June 2000.
Diagnostic AidsImportant: If DTCs P0745, P0746, P0756, P0758, P0761, P0763, P0766, P0768 or P0789 is set, diagnose that DTC first. A diagnosed PC solenoid, shift solenoid 2, 3 or 4 low/high circuit fault DTC may have caused DTC P0733 to set.Important: If a shift solenoid performance DTC P0783, 4th gear stuck ON, is set, diagnose that DTC first. A 4th gear stuck ON may cause no 3rd gear, no 2nd gear, or TCC stuck Off.
Refer to Pressure Ports - Air Check and Parts Description for pressure apply points and for component/location description.
Possible causes of no 3rd gear are listed in the flowchart on the succeeding page.
Verify TRANSMISSION ISS and TRANSMISSION OSS read correctly on Scan tool.
Make sure the pressure control, shift 2, shift 3 and shift 4 solenoids are not intermittently sticking. A sticking shift solenoid 4 may cause 4th gear to be applied from an initial start resulting in no 3rd gear. Audible sound should be similar for all solenoids. A muffled tone indicates the need for replacement.
Check this pinout HERE
P0734 refer at ratio 4 gear, and the rocedure is the same.
Hope helps.

Apr 03, 2012 | 2003 Ford Focus

1 Answer

I have a 99 mustang v6 3.8 automatic. The problem that I am having is that when the transmission is going into 3rd gear it revs higher (about 2300 - 2500 rpm) before going into 4th gear and this usually...


Sounds like a solenoid problem, which is causing a fair or slippage into 3rd gear. If you have a solenoid pack in trans, you need to change it. Don't drive it at all ,that way. Find out what trans unit or model you have,by stopping at a trans shop and asking lots of questions. Then go home, pull the pan and change yourself,if applicable.

Sep 16, 2010 | Ford Mustang Cars & Trucks

1 Answer

My mustang feels like it's slipping


I have this sane issue on a 2006 Mustang, I thought it was the Clutch, have been adv's by for it is not, but I am not to sure, happend 1st and 2nd gear

Ken

May 20, 2008 | 2008 Ford Mustang

Not finding what you are looking for?
2009 Hyundai Tucson Logo

Related Topics:

451 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8274 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...