Question about 1999 Dodge Caravan

2 Answers

How do i remove rear drivers tail lamp assembly

Posted by on

  • maverick4t8 Nov 18, 2009

    I NEED TO REMOVE AND REPLACE A TAIL LAMP ASSEMBLY ON MY 1999 CARAVAN

×

Ad

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 4,472 Answers

  1. Step 1 Determine which taillight needs replacing. Open your Dodge Caravan's rear hatch. Look inside the vehicle directly behind where the taillight is located on the outside.
  2. Step 2 Look for two flat, black discs about the same diameter as a dime. Use a screwdriver or pliers to pry off the discs.
  3. Step 3 Remove both parts of the disc mechanism, the grommet and the plug. Push the plug backwards (toward the outside of the Dodge Caravan) through the grommet.
  4. Step 4 Hold on to the lens assembly as you remove the second grommet. The Dodge Caravan's lens assembly can fall off and break.
  5. Step 5 Notethe wiring inside that connects to a plug. Near the wiring, you shouldsee two round covers with tabs on either side. These are bulb housingsand they contain the bulbs.
  6. Step 6 Pressinward on the tabs and pull to remove the covers. Pull out the old bulband push in a new one. Squeeze inward on the tabs again to replace thecovers on the bulb housing. You should hear a snap if the covers areproperly replaced.
  7. Step 7 Checkthe taillight to make sure it works properly with the new bulb inplace. Push the wiring back in and replace the lens assembly.
These steps for replacing the bulbs should give you the information your looking for. if you need any further information please let me know.
Thank you,
lee

Posted on Nov 18, 2009

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 3,489 Answers

Once you open the rear deck(door) look at the tail lamp assembly and there should be a couple of screws.

Posted on Nov 18, 2009

  • Kori Policy
    Kori Policy Nov 18, 2009

    this is how it is done whether you want to replace the bulbs or the assembly itself.

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to change brake light bulb on a 2014 fiat 500L


https://www.fiatusa.com/download/pdf/manuals/2014-FIAT-500L-OM-1st.pdf

it's in your owners manual page 358 chapter 7

you need a torx 20 screwdriver or bit

Rear Tail, Stop, Backup And Turn Signal Lamps
1. Open the liftgate.
2. Remove the two screws and remove the tail lamp assembly.
3. Remove the four screws (using a T20 driver) and separate the backplate from the lamp housing.
4. Remove the tail, stop, or turn signal bulbs by pushing them slightly and turning counter-clockwise.
5. Remove the backup lamp bulb by pulling straight out.
6. Replace lamps as required and reinstall lamp.

Center High-Mounted Stop Lamp (CHMSL)
This light is an LED assembly. See your authorized stealership

Mar 30, 2015 | Fiat Cars & Trucks

1 Answer

Change license plate bulbs in 2004 buick lesabre custom


  1. Disconnect the tail/back up lamp harness connector from the from the body wiring harness.
  2. Remove the tail/back up lamp assembly from the rear compartment lid.
  3. While supporting the tail/back up lamp assembly, unplug the tail/back up lamp harness grommet from the rear compartment lid and remove the tail/back up lamp from the vehicle.
  4. Remove the license plate lamp bulb from the lamp housing.

Sep 22, 2014 | 2004 Buick LeSabre

1 Answer

2009 impala rear turn signsl bulb replacement


Tail Lamp Replacement Impala
1596323.gif
tif.gif
Callout
Component Name
Preliminary Procedures
  1. Open the rear compartment lid.
  2. Remove the nut securing the rear compartment trim the backside of the tail lamp assembly.
  3. Pull down the rear compartment trim liner.
1
Tail Lamp Assembly Nuts (Qty: 2)
Caution: Refer to Fastener Caution in the Preface section.
Tighten
2 N·m (18 lb in)
2
Trunk Trim Line Nut
Tip
Ensure the trim liner nut is installed after the liner is repositioned in the rear compartment.
3
Tail Lamp Assembly
Tip
Pull rearward to remove and connect the electrical connector and push lamp inward in order to position the lamp to the body panel.
4
Rear Lamp Harness Connector
Ensure to connect the lamp harness connector before securing the lamp to the rear body panel.

Jul 29, 2011 | Chevrolet Impala Cars & Trucks

2 Answers

How can i change a tail light an a sorento kia 2008? I can t reach the connector inside..... What do i have to take off? Thank you


To Remove

1. Disconnect the negative (-) battery terminal.
2. Loose the 2 screws holding the rear combination lamp then disconnect the connector. And then remove the outside rear combination lamp assembly.
3. Remove the bulbs from the rear combination lamp assembly.


tecnovative_179.gif

tecnovative_180.gif
To Install

1. Connect the bulbs to the rear combination lamp assembly.
2. Connect the rear combination lamp connector.
3. Reassemble the rear combination lamp assembly.

Mar 24, 2011 | 2007 Kia Sorento LX 4x4

1 Answer

License plate bulb replacement on a 2002 Buick LeSabre I don't have screws holding the bulb assembly in place. It appears to be in place with tabs larger than the assembly holding the assembly in...


Hi, my name is John I will do my best to assist you.

The entire tail/backup lens assembly has to be removed from the trunk lid as shown in the drawing attached. There will most likely be some nut's or clip's on the assemblies mounting pins on the inside of the trunk lid.
  1. Disconnect the tail/back up lamp harness connector from the body wiring harness.
  2. Remove the tail/back up lamp assembly from the rear compartment lid.
  3. While supporting the tail/back up lamp assembly, unplug the tail/back up lamp harness grommet from the rear compartment lid and remove the tail/back up lamp from the vehicle.
  4. Remove the license plate lamp bulb from the lamp housing.
  5. Installation is the reverse of removal.

tecnovative_128.gif
If you have more specific questions please post comments to this thread and I will endeavor to monitor new activity and respond as soon as possible. I recommend that you "bookmark", or "add to favorites" this page for your convenience.

Feb 15, 2011 | 2002 Buick LeSabre

1 Answer

Need to replace stop light


Tail Lamp Assembly Removal & Installation To Remove:
Tail lamp assembly removal and installation gm-06-00-1645.gif

  1. Remove the tail lamp assembly retaining screws from the body.
  2. Release the locking pins by pulling the assembly directly rearward.
  3. Disconnect the tail lamp assembly connector.
  4. Remove the tail lamp circuit board from the assembly.
To Install:
  1. Install the tail lamp circuit board into the assembly.
  2. Connect the tail lamp assembly connector.
  3. Push the assembly directly forward into the opening to engage the locking pins.
  4. Install the tail lamp assembly retaining screws into the body. Torque the screws to 17 in-lb (1.9 Nm).
High Mount Stop Lamp Removal & Installation To Remove:
CAUTION
Raising the liftgate with the liftgate window open can damage the high mount stop lamp, liftgate hinges, and the liftgate window.
  1. Raise the liftgate.
  2. Lower the rear of the headliner by removing the rear headliner pins.
  3. Disconnect the high mount stop lamp connector.
  4. Remove the high mount stop lamp grommet from the body.
  5. Lower the liftgate.
  6. Open the liftgate window.
  7. Remove the high mount stop lamp retaining screws from the liftgate window molding.
  8. Remove the high mount stop lamp from the vehicle.
To Install:
  1. Place the high mount stop lamp onto the vehicle.
  2. Install the high mount stop lamp retaining screws into the liftgate window molding. Torque the screws to 22 in-lb (2.5 Nm).
  3. Close the liftgate window.
  4. Lift the liftgate.
  5. Install the high mount stop lamp grommet into the body.
  6. Connect the high mount stop lamp connector.
  7. Install the rear of the headliner by inserting the retaining pins.
prev.gif next.gif

Oct 18, 2010 | 2004 GMC Envoy

1 Answer

What do I need to unscrew in the trunk to change the reverse light in my 01 chevy impala


Tail Lamp Assembly Removal & Installation To Remove:
  1. Open the rear compartment.
  2. If equipped, disconnect the cargo net.
  3. Remove the wingnut and pull back the rear compartment trim panel.
  4. Remove the wingnuts from the tail lamp assembly.
  5. Remove the tail lamp assembly from the rear body panel.
  6. Disconnect the electrical connector from the tail lamp assembly.
  7. Remove the tail lamp socket by turning counterclockwise.
  8. Remove the side marker lamp socket by turning counterclockwise.
To Install:
  1. Install the side marker lamp socket by turning clockwise.
  2. Install the tail lamp socket by turning clockwise.
  3. Connect the electrical connector to the tail lamp assembly.
  4. Position the tail lamp assembly to the rear body panel.
  5. Install and secure the wingnuts that attach the tail lamp assembly to the body panel.
  6. Position the rear trim panel to the rear compartment. Install and secure the wingnut.
  7. If equipped, connect the cargo net.
  8. Close the rear compartment.
prev.gif next.gif

Oct 18, 2010 | 2001 Chevrolet Impala

1 Answer

I would like to know how to remove my 03 lincoln aviator tail lamp as I need to replace it. Thank you..


here's mountaineer, it should be similar

SECTION 417-01: Exterior Lighting 2002 Explorer/Mountaineer Workshop Manual
REMOVAL AND INSTALLATION Rear Lamp Assembly —Mountaineer Removal and Installation
  1. Raise the liftgate and remove the rear lamp assembly screws.
  1. Remove the rear lamp assembly.
    • Disconnect the electrical connectors.
  1. To install, reverse the removal procedure.
    • If necessary, install new tail lamp bulbs.
8966cfe.gif

Aug 01, 2009 | 2003 Lincoln Aviator

2 Answers

Left rear turn signal bulb is burned out.


Tail Lamp Assembly
Removal & Installation
To Remove:

  1. Open the rear compartment.
  2. If equipped, disconnect the cargo net.
  3. Remove the wingnut and pull back the rear compartment trim panel.
  4. Remove the wingnuts from the tail lamp assembly.
  5. Remove the tail lamp assembly from the rear body panel.
  6. Disconnect the electrical connector from the tail lamp assembly.
  7. Remove the tail lamp socket by turning counterclockwise.

  1. To Install:
  2. Install the tail lamp socket by turning clockwise.
  3. Connect the electrical connector to the tail lamp assembly.
  4. Position the tail lamp assembly to the rear body panel.
  5. Install and secure the wingnuts that attach the tail lamp assembly to the body panel.
  6. Position the rear trim panel to the rear compartment. Install and secure the wingnut.
  7. If equipped, connect the cargo net.
  8. Close the rear compartment.
      Please don't forget to rate !!!!!!

    Mar 28, 2009 | 2002 Buick Century

    1 Answer

    How do i get the cover off the license plate bulbs?


    REMOVAL PROCEDURE
    1. Disconnect the tail/back up lamp harness connector from the from the body wiring harness.
    2. Remove the tail/back up lamp assembly from the rear compartment lid.
    3. While supporting the tail/back up lamp assembly, unplug the tail/back up lamp harness grommet from the rear compartment lid and remove tail/back up lamp from the vehicle.
    4. Remove the license plate lamp bulb from the lamp housing.
    INSTALLATION PROCEDURE
    1. Install the license plate bulb into the lamp housing.
    2. While supporting the tail/back up lamp assembly, install the tail/back up lamp harness grommet to the rear compartment lid and install the tail/back up lamp. NOTE: Refer to Fastener Notice in Service Precautions.
    3. Install the tail/back up lamp fasteners to the tail/back up lamp studs. Tighten Tighten the tail/back up lamp fasteners to 6 N.m (53 lb in) .
    4. Connect the tail/back up lamp electrical connector.
    5. Connect the tail/back up lamp harness connector and clip the connector to the metal edge of the rear compartment lid.

    Feb 25, 2009 | 2000 Buick LeSabre

    Not finding what you are looking for?
    1999 Dodge Caravan Logo

    Related Topics:

    40 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Dodge Experts

    yadayada
    yadayada

    Level 3 Expert

    76132 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22156 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    8273 Answers

    Are you a Dodge Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...