Question about 1993 Ford Ranger SuperCab

1 Answer

HOW TO INSTALL CAM SENSER ON 1993 FORD RANGER 4.0

HOW SHOULD I INSTALL CAM SENSER ON 1993 FORD RANGER 4.0
THE MOTOR IS ALREADY TORN DOWN AND OLD SENSER IS OUT.

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 120 Answers

Its right behind the intake manifold. its a B*&^h to get off but you need a special tool you can get a most auto part stores. you have to make sure your #1 piston is TDC on your compression stroke. then drop in your sensor, align it to what your specs say

Posted on Nov 18, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I go about sitting the timimg on a 94 ford ranger lt pickup


On the 4 cyl engine, you line up the crank pulley with the timing mark and the cam gear with the pointer on the timing cover.
On V6 engines the cam and crank gear dots point at each other. 6 oclock for the cam and 12 oclock for the crank.

Jun 16, 2015 | Ford Ranger Cars & Trucks

2 Answers

Where is the cam shaft senser on a ford ranger 2.5 td 2002


Ford did not put a 2.5 in a Ranger, maybe a 2.3 ?
2.3 = 2007-01-27_154722_2.gif
3.0 - The CMP sensor& synchronizer/shaft are located behind the intake manifold (i.e., back near the firewall on a Ranger) on the top of the cylinder block. If you just need to replace the sensor, it is a simple job of unplugging the electrical connector and removing the screws holding the sensor in place. Here is a sketch of the sensor to give you an idea what to look for:

Jun 17, 2014 | 2002 Ford Ranger Regular Cab

1 Answer

1993 Ford Ranger


need the diagram timing ford ranger 1993 motor 3.0L

Dec 07, 2013 | 1993 Ford Ranger SuperCab

2 Answers

How to remove a stsrter on a 1993 ford ranger


Hi. here's the procdeure on how to remove and replace new starte for your truck.

  1. Step 1 Disconnect the battery's negative cable from the battery using the battery wrench.
  2. Step 2 Lift the right front end of the Ranger with the floor jack and then lower it onto the jack stand. Make sure the jack stand is under the right front frame, but does not impede your access to the starter.
  3. Step 3 Climb under the Ranger with the socket set and unbolt the starter wiring using the socket set.
  4. Step 4 Support the body of the starter with one hand while you remove the two starter-mounting bolts with the socket set using your other hand. Do not let the starter rest on the loose bolts at any time during this process.
  5. Step 5 Set the old starter off to the side and hold the replacement starter in position. Thread the mounting bolts back in by hand and then tighten them down with the socket set. Once again, do not let the starter's weight rest on the bolts until you tighten them down fully.
  6. Step 6 Bolt the starter wiring to the new starter using the socket set.
  7. Step 7 Climb out and lower the Ranger off the jack stand using the floor jack. Reconnect the negative battery cable with the battery wrench.

Aug 12, 2010 | 1993 Ford Ranger SuperCab

1 Answer

Cam senser


I believe you need to line up the line with the arrow.

Aug 06, 2008 | 1995 Ford Explorer

1 Answer

1993 ford ranger


transmission put d en the motor turn on off

Jun 15, 2008 | 1993 Ford Ranger SuperCab

Not finding what you are looking for?
1993 Ford Ranger SuperCab Logo

Related Topics:

182 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5520 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...