Question about 1991 Toyota Pickup

2 Answers

91 toyota pickup with clutch problems

I have a 91 toyota pickup 4wd manuel trans I just changed the clutch and now it is letting out at the very bottom all at once and it does not want to go in change gears what can i do

Posted by on

  • lv2fish27 Nov 18, 2009

    yes i actually changed the slave cylinder and bled it probly a total of around 15 to 20 times because that is what I thought was wrong but its still the same could there still be air or could it be something else

  • John Remenyi May 11, 2010

    When replacing the clutch, did you disconnect the slave cylinder? If so, did you bleed the hydraulic clutch after reassembly? If there is air trapped in the clutch system, it will prevent adequate pressure transfer to the slave cylinder/throwout bearing, which could cause the problem you describe.



2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 5 achievements.


    An expert whose answer got voted for 20 times.


    An expert who has answered 20 questions.

  • Expert
  • 97 Answers

First you have to bleed air from clutch fluid.
if it is not ok, Remove clutch agan & check pressure plate finger blance or damage.

Posted on Nov 18, 2009

Testimonial: "thanks"

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert whose answer got voted for 500 times.

  • Master
  • 1,615 Answers

Sounds like you put it on backwards

Posted on Nov 18, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

93 toyota 4wd makes loud noise when i push the clutch in.

you may have a "throwout bearing" problem. the mechanic is WRONG. you will need to take the trans out and most likely replace the clutch components but the problem is not in the trans.

Oct 09, 2009 | 1986 Toyota Pickup 4WD

1 Answer

What type of transmission fluid for a 1992 toyota pick p

Auto dextron III ATF..  capasity A340H total fill 10.3 liters A340E total fill 7.2 liters. 
Manuel 75W-90  capasity 2WD G57 trans 2.2 liters 4WD G58 trans 3.0 liters. all other 3.0 liters 
Good luck and keep me posted. be glad to help.

Jul 01, 2009 | 1992 Toyota Pickup

1 Answer

Clutch won't engage

There is a problem with the pressure plate spring or possibly the throwout bearing is bound up,you should be able to pull the rubber boot from around the clutch fork and have someone depress the pedal,you should be able to see if it's a problem with the bearing.Unfortunatly the trans is probably going to have to caome off.

May 25, 2009 | 1991 Toyota Pickup

3 Answers

1991 Toyota pickup 4WD clutch slipping

There is an adjustment for the clutch pedal under the dash where the push rod goes thru the firewall. There is only aprx. 1/2" of adjustment so be careful when making an adjustment, if your clutch is slipping then you need to shorten the throw of the push rod.

May 06, 2009 | 1991 Toyota Pickup

1 Answer

New clutch slips when hot

it is possible. maybe u should have put a heavy duty clutch in. sounds like a work horse.

Apr 03, 2009 | 1986 Toyota Pickup 4WD

1 Answer

Clutch replacement 91 pickup 4x4 toyota

ase mechanic:

well depends how strong you are, and if you are using a car lift or doing on your back. either way drain the transfer case fluid, should be bolt on bottom, otherwise when you seperate the transfer case from trans there will big mess. take transfer case off first note how it is mounted with paint marker and then take trans out. much easier then leaving together.

Jan 29, 2009 | 1991 Toyota Pickup

1 Answer

4wheel drive won't engage

it has to be a linkage problem. the linkages had to be re moved to get the clutch out and have not been put back on correctly or at all.the clutch has no bearing at all on the engaugeing of 4wd

Nov 23, 2008 | 1988 Toyota Pickup

2 Answers

91 4x4 Toyota Pickup Overheating

did you take out the thermostat?
If not do that if so it might be a feul mixture problem. To lean will make it run hot

Jun 21, 2008 | 1991 Toyota Pickup

2 Answers

Transmission shift lever - 91 Toyota V6 4WD pickup

Easy fix! Remove boot, take out four screws, shifter pops up, replace bushing! Keep it in neutral before starting.

May 18, 2008 | 1991 Toyota Pickup

Not finding what you are looking for?
1991 Toyota Pickup Logo

Related Topics:

586 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts


Level 3 Expert

80637 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8841 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides