Question about 2004 Ford Explorer

1 Answer

When shifting and accelerating there there is slipping and a loud clunk. What could be the problem?? Transmition..

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 120 Answers

Have the u-joint checked sound like you got 1 ready to break

Posted on Nov 18, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What are some of the signs that transmition cluch plate is going out?


first question =---manual or automatic
next are there any other symptoms ( slipping, shudder on take off, difficult to select 1st gear or reverse )
I would be looking at the drive shaft "U" joints and cv joints first because once a clutch is engaged there will be no noise under acceleration of deceleration
look for failed engine/transmission mounts and suspension rubbers worn out

Oct 25, 2015 | 1993 Dodge Dakota

1 Answer

My 1999 jeep grand cherokee is making a loud clunking sound when I accelerate and then starts sputtering/jerking until I reach about 70mph


the bad news is that when that noise starts is either 3 things
1. your rod bearing has slipped and is about to break
2. you have a stuck lifter
3. finally you may be just low on oil

Nov 25, 2013 | Cars & Trucks

1 Answer

99 Grand Cherokee. Started with locking or binding with loud clunks. After long drive, rear diff was smoking and was replaced. Just drove it and after shifting into all time 4wd and then back to 2wd did it...


Sounds like a bad transfer case. Generally what you experienced is caused by a tire mis-match but can also happen by itself sometimes. GC's use a fluid coupler that is supposed to engage 4wd when tires begin to slip. (coupler is pretty much the same as the mechanical clutch unit on your fan, only larger) If the coupler fails, symptoms like yours happen.

Mar 27, 2011 | 1999 Jeep Grand Cherokee

1 Answer

My is shifting from 2 to drive back to 2 why is it doning that


Check your tranny fluid levels- if they are low your transmition will slip between gears, however if you notice any kind of free reving while its shifting (like being reved up when in park or neutral) then the hydrostatic clutches are slipping and the transmition needs repair.

Another thing you should investigate is your transmition kick down bar (it shifts the trany into a lower gear when accelerating hard to help pick up speed.

Apr 07, 2010 | 1999 Dodge Ram 2500 4WD

1 Answer

Transmition not shifting automaticaly on 2001 pt -cruiser


Check the fluid level and add the proper amount if needed. If the level is fine, take it to a shop. It sounds like the transmission is slipping, and the heat generated will quickly kill it.

Nov 07, 2009 | 2001 Chrysler PT Cruiser

1 Answer

Clunk in trans


If this is a 4X4 then the problem is most likely the slip yoke not sliding smoothly on the transfer case output shaft splines. You can correct this bt lubricating the slip yoke splines with Teflon Grease .
If it is a 4X2 then lube the output shaft splines on the back of trans.

Jan 25, 2009 | 2002 Ford F150 Regular Cab

1 Answer

Acura Integra '92 loud clunking when accelerating


you can check the wheels make sure there on tight and make sure you tie rods and wheel bearings are good

Dec 30, 2008 | 1992 Acura Integra Hatchback

1 Answer

I get a very loud clunk when I put the transmission into drive or reverse. I remove my foot from the accelerator to allow the transmission to go to the next gear otherwise it goes above 3,000 rpm to...


Try replacing your fluid filter in your transmission first. If that does not work, your tranny could have the gears wearing out. To solve the shifting problem, have a shift kit put in your transmission.

Jul 30, 2008 | 1990 Toyota Camry

Not finding what you are looking for?
2004 Ford Explorer Logo

Related Topics:

111 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5471 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...