Question about 1999 Dodge Ram

1 Answer

Can't start my truck after changing my fuel filter

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,985 Answers

Verify that flow printed on filter is going towards engine.

Posted on Nov 18, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1992 F350-7.3 4wheel drive is hard to start after changing fuel filter and fuel pump. Why is it hard to start?


indicates fuel leak back and fuel pressure drop
check filter installation for seal not sitting properly, loose fuel line fitting , pump installed correctly (flow wise ), filter installed correctly (flow wise)
air getting in to fuel lines
the thing you are looking for is indicated by the initial hard start but when started runs ok ( good fuel to the engine eventually) and then by the fact that if the engine is allowed to sit for a long period the problem returns meaning that the fuel pressure is not being held
could even be a problem fuel pressure regulator allowing the fuel to bypass ( no pressure =hard starting) then gets enough pressure to run ok but allows that pressure to drain off over time

Oct 29, 2016 | 1992 Ford F350

2 Answers

I changed my fuel filters on my 6.4 l f150 2008 now won't start .I cycled engine but smelled a faint smell and saw light smoke from under hood .charge batt.still won't spin .did started go out too


F350 6.4 L 2008 Wont Start after Fuel Filter Change - Ford Truck ...

www.ford-trucks.com > ... > Super Duty & Heavy Duty
Dec 8, 2011 - F350 6.4 L 2008 Wont Start after Fuel Filter Change Super Duty & Heavy Duty. ... My only suggestions are change them again or take it to Ford. ...Rancho 9000 shocks 1992 F150 XLT 2x4 Standard Cab Long Bed 302 ... Priming it now won't help, because the air bubbles are already past the fuel return line. 2008 won't start after fuel filter change!
Aug 5, 2012
Fuel Filter change problem
Jan 7, 2011
F-350 won't start after oil change and fuel filters changed ...
Dec 10, 2010
Need help fuel filter change now it wont start
Jul 2, 2010
More results from www.ford-trucks.com

Jan 25, 2016 | Cars & Trucks

1 Answer

How can I fix a no start issue? cranks but won't start


Uh oh, you may have had to bleed the air out of the fuel system after the filter change. You may damage the fuel pump ($$$$$) by cranking the engine with no fuel to lube the very high pressure fuel pump. It started a few times because there was still fuel in the pump. Now it's dry.

May 13, 2014 | 2010 Ford F-250 Super Duty

1 Answer

Changed fuel filter now truck will not start


diesel? full fuel filter housing with fuel

Mar 18, 2013 | 2005 Ford F 350 Super Duty

1 Answer

2010 ford mondeo diesel wont start after changing fuel filter, please help!


on a ford mondeo 08 the fuel filter is at the rear of car u take old filter put in new one fill with fuel put back together then put a pipe on feed [there might be a bleed niple on top that will be easier] suck till fuel comes out conect pipe back turn ignition on for 15 seconds 3 times to clear air then start done

May 20, 2012 | Cars & Trucks

1 Answer

Fuel is flowing from the tank to the engine, but will not start. Engine will start if fuel is provided through the air intake port at the air filter.


check fuel filter and fuel pump,if the filter clugged change it, if pump doesnt work change both pump and filter.

Oct 02, 2010 | 1993 Chevrolet Astro

2 Answers

Fuel filter on a 6.2 diesel


You need to install an electric fuel pump to lift the fuel from the tank to the mechanical pump. You can turn off the electric pump after starting or use it when bleeding the lines after changing the fuel filter. You can start the truck after a few minutes instead of a few days. I know from experience and fought that problem for years.

Dennis.

Oct 26, 2008 | GMC C2500 Cars & Trucks

1 Answer

Changing f250 fuel filter (gas)


Sounds like a fuel pump, but start with the filter.

Sep 28, 2008 | 2001 Ford F250 Super Duty Super Cab

Not finding what you are looking for?
1999 Dodge Ram Logo

Related Topics:

44 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8123 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...