Question about 1991 Ford Mustang

1 Answer

My sons 91 mustangs low beams went out together. the fuse was blown so we put another one in but they still wont work. any ideas?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

    Governor:

    An expert whose answer got voted for 20 times.

  • Expert
  • 172 Answers

I have a mustang and a common problem with the headlights is the in dash switch goes bad play around with the switch turning it on and off firmly and see if you get the lights to come and replace the switch ......also the headlights have a relay for them to located in the front around the lights trace the wires to locate the relay ...Hope this helps you out

Posted on Nov 18, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Headlights wont work on 1998 mustang v6 Running lights brake lights and gauge lights work fine. The lights only trn on when i hold the high beam switch. Any suggestions?


check fuses and check globes . Globes might have two filaments and low beam ones has blown . Had this globe thing happen on two globes at the same time on Ford Falcon's Halogon globe headlights.

May 05, 2014 | Cars & Trucks

1 Answer

Low beam not working on 97 Mitsubishi Lancer. Park ok, hi beam ok. Lamps test ok.


If Dual beam bulbs, low beam on light may be blown. I just had the same problem on my '91 Camaro. Could also be a simple fuse replacement, find correct fuse, , replace, and recheck.

Sep 26, 2013 | Mitsubishi Lancer Cars & Trucks

1 Answer

Both low beams do not work. High beams do work


check fuses for low headlight fuse blown highly unlikely both bulbs went out at once.

Jan 03, 2010 | 2003 Chevrolet Impala

1 Answer

Low Beam Lights won't work. High Beam works fine.


hey
id say check your fuses, if the two lights went at once then its more than likely a case of changing the blown fuse. The fuses are located usually under the dash on the drivers side with some also in the engine bay.
good luck

Dec 30, 2009 | 1996 Pontiac Sunfire

1 Answer

In our 2002 Honda Accord LX both low beam lights went out together but the high beams work fine. They went out together, what could be the cause?


Before you do anything else, you should check fuse number 2 (7.5 amp) in your engine compartment fuse box. It is your dimmer relay fuse. Fuse number 1 (20 amp) is your left headlight and fuse number 3 (20 amp) is your right headlight.
If the number 2 fuse is blown, and you replace it, if it blows again, I would have the system checked.
Hope this helps you.

Oct 31, 2009 | 2002 Honda Accord

2 Answers

Have an xc90 with bulb failure low beam warning light replaced both low beam bulbs with no success. any ideas????


fuse #38 on the inside inside fuse panel was blown on mine, replaced and lights work fine.

Jul 08, 2009 | 2004 Volvo XC90

1 Answer

No low beams.


To start ensure that it is not just a blown fuse. If that is not the problem, then you need to read voltages at the back of fuse box, to check if there is volts on wiring from fuse out to light when switch is on. If there is no power you localize the problem on wiring from light switch to fuse box. In this case you may need to take apart the steering column to repair wiring harness (switch has already been replaced).
If instead there is power getting to light fuse, and power out from fuse box to light, then test and repair the wiring to lights from fuse box, if you do not find the problem you may need a rebuild. This can be done by a mechanic or by a car electrician.

Apr 17, 2009 | 1992 Ford Mustang

3 Answers

Fuse diagram for 91 chevy corsica


Need copy of wiring schematic for 1991 chevy corsica

Dec 10, 2008 | 1991 Chevrolet Corsica

Not finding what you are looking for?
1991 Ford Mustang Logo

146 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

fordexpert

Level 3 Expert

5495 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...