Question about 1994 Mercury Villager

1 Answer

The driver side headlamp on my '94 Mercury Villager goes on and off. The electrical connector (plug) seems to have play in it when inserted as far as possible. If I wiggle it, it may go off. Will a new bulb fix the problem?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,985 Answers

No you need to remove wire and squeeze connector tighter

Posted on Nov 18, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to remplace a wather pump in a 94 mercury villager


I have shop manual & wiring book for 94 Villager for $25 plus postage. Let me know if interested.

go here for help too. It's an all day job but you can do it. Need to note where each bolt goes cause some are different sizes.

http://groups.yahoo.com/group/villagerquest/

Mar 31, 2010 | 1994 Mercury Villager

1 Answer

Where is the flasher located in a 1999 Mercury Villager>


1999 Mercury Truck Villager Wagon 3.3L SFI SOHC 6cyl
Flashers
The turn signal/hazard lamp flasher is located behind the driver's side of the instrument panel to the right of the steering column.

REPLACEMENT
  1. Disconnect the negative battery cable.
  2. Locate the flasher assembly under the driver's side of the instrument panel. Press the tab on the flasher and slide it from the bracket.
  3. Detach the flasher from the electrical connector and remove the flasher from the vehicle.
  4. The installation is the reverse of the removal.
Hope help with this (remember rated and comment this).

Mar 13, 2010 | 1999 Mercury Villager

1 Answer

I have a 94 Mercury Villager and would like to know the exact locatin of the fuel pump reset switch


Under hood, driver side, front engine area, rear of headlight housing, front of battery, mounted in fuse/relay block

Jan 24, 2010 | 1997 Mercury Villager

1 Answer

Dashboard lights burning out, down to 1 illuminating tach, speedo, gas gauge. How complicated to replace?


one hour job. find bulb part number in bulb chart in owner manual.

go here for villager help.

http://groups.yahoo.com/group/villagerquest/

Section 13-01B: Instrument Cluster — Conventional 1996 Villager Workshop Manual
REMOVAL AND INSTALLATION Instrument Panel Finish Panel Removal
  1. Disconnect the battery ground cable (14301).
  1. Block the wheels (1007) to prevent the vehicle from moving.
  1. Turn the ignition switch (11572) to the OFF position.
  1. Shift the transmission range (TR) selector to MANUAL LOW (1).
  1. Tilt the steering wheel (3600) to the lowest position, if equipped with a tilt wheel.
  1. Remove the two instrument panel finish panel screws.
  1. Remove the instrument panel finish panel (044D70) enough to access the switch electrical connectors.
  1. Disconnect the rear windshield wiper/washer switch electrical connector.
  1. Disconnect the heated back window and light switch electrical connector.
  1. Disconnect the emergency warning switch electrical connector.
  1. Disconnect the SECURITY indicator light electrical connector.
  1. Disconnect the speed control on/off (CRUISE CONT. ON/OFF) switch electrical connector.
  1. Disconnect the headlamp switch electrical connector.
  1. Disconnect the autolamp/light switch rheostat resistor electrical connector.
  1. Remove the instrument panel finish panel with the switches attached.
-------------------------------------------------------------------------------------------------
Instrument Cluster
Removal
  1. Disconnect the battery ground cable (14301).
  1. Block the wheels (1007) to prevent the vehicle from moving.
  1. Turn the ignition switch (11572) to the OFF position.
  1. Shift the transmission range (TR) selector to MANUAL LOW (1).
  1. Tilt the steering wheel (3600) to the lowest position, if equipped with a tilt wheel.
  1. Remove the two instrument panel finish panel screws.
  1. Remove the instrument panel finish panel (044D70) enough to access the switch electrical connectors.
  1. Disconnect the rear windshield wiper/washer switch electrical connector.
  1. Disconnect the heated back window and light switch electrical connector.
  1. Disconnect the emergency warning switch electrical connector.
  1. Disconnect the SECURITY indicator light electrical connector.
  1. Disconnect the speed control on/off (CRUISE CONT. ON/OFF) switch electrical connector.
  1. Disconnect the headlamp switch electrical connector.
  1. Disconnect the autolamp/light switch rheostat resistor electrical connector.
  1. Remove the instrument panel finish panel with the switches attached.
  1. Remove the four instrument cluster screws.
  2. Remove the transmission range indicator (7A110) from the instrument cluster (10849).

Jan 13, 2010 | 1995 Mercury Villager

1 Answer

Headlamp replacement



1. Unplug the three-prong electrical connector.
2. Pull off rubber boot on back of headlamp
3. A spring clip holds the bulb in the assembly. Un-hook one side and swing the clip back.
4. Slide the old bulb straight out.
5.Wearing disposable gloves so that skin oil doesn't get on the new bulb, open the new bulb's package and insert the new bulb straight into the holder, making sure it goes all the way to the front. The middle electrical prong should be up.
6. Swing the retaining spring back and re-clip.
7. Slide the rubber boot back on the rear of the assembly, making sure that the electrical prongs are exposed.
8. Re-connect the three-prong electrical connector.
9. Turn on lights and make sure it works.

Oct 13, 2009 | Mazda MPV Cars & Trucks

4 Answers

2004 Chevy Trailblazer, both headlight plugs burnt


bad connections at the headlamp plugs will cause a burnt connector. I would suggest replacing the plugs. Should be able to buy a pigtail plug at the dealer. Then cut old wires off close to the plug. Connect new plug using solder and shrink tubes for a better connection. May sure your headlamp switch is off when doing any of the above. Hope this helps

Aug 06, 2009 | 2004 Chevrolet TrailBlazer

2 Answers

How to change a headlight bulb on my 95 villager


1.- Carefully unplug the wires connected to the bulb located inside the headlamp, be sure to glently press the far side of the plug (where the wires come out) there's a rectangular shaped lock and pull the plug.
2.- Carefully turn the donut ring that holds the bulb in its position by turning it about 1/4 turn counter clockwise and pull it out.
3.- Pull the bulb out gently (never touch the glass) just the plastic base.
4.- Place the new bulb inside and be sure it is in the same position as the old one.
5.- repeat step 2 and 1 backwards.
There should be no problem

Jul 11, 2009 | 1995 Mercury Villager

1 Answer

Door issue


no difference from 93 to 98. you need to move door hinges.

go here for villager/quest help

http://autos.groups.yahoo.com/group/villagerquest/

Apr 18, 2009 | 1993 Mercury Villager

1 Answer

Replacing headlight bulb of 2001 mercury villager?


SECTION 417-01: Exterior Lighting 2001 Villager Workshop Manual REMOVAL AND INSTALLATION Bulb —Headlamp Removal
  1. s1v~us~en~file=ani_caut.gif~gen~ref.gif WARNING: The halogen bulb contains gas under pressure. The bulb may shatter if the glass envelope is scratched or if the bulb is dropped. Handle the bulb only by its base. Grasp the bulb only by its base. Avoid touching the glass envelope.
    NOTE: The headlamp bulb should not be removed from the headlamp until just before a replacement bulb is installed. Removing the bulb for an extended period of time may affect headlamp bulb performance. Contaminants may enter the headlamp where they can settle on the lens and reflector. Never turn on the headlamps with the bulb removed from the headlamp.
    NOTE: Make sure that the headlamp switch and the ignition switch are in the OFF position.
    Remove the headlamp bulb.
    1. Disconnect the electrical connector.
    1. Remove the headlamp bulb retainer by rotating it counterclockwise about one-eighth of a turn.
    1. Remove the headlamp bulb.
0deebe4.gif Installation
  1. Install the headlamp bulb.
    1. Install the headlamp bulb.
    1. Install the headlamp bulb retainer by rotating it clockwise about one-eighth of a turn.
    1. Connect the electrical connector.
------
go here for villager help

http://autos.groups.yahoo.com/group/villagerquest/

Apr 04, 2009 | 2001 Mercury Villager

Not finding what you are looking for?
1994 Mercury Villager Logo

Related Topics:

80 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

fordexpert

Level 3 Expert

5470 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...