Question about 1994 Chevrolet S-10 Blazer

1 Answer

Do i need to greese or lube new a arm bushings on 95 chevy s-10 2wd

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,985 Answers

Only if it came with grease fittings

Posted on Nov 18, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2008 Chevy HHR front rear control arm bushing installation


Hi Dan:
If you have a micrometer (fancy word for a very accurate measuring tool) you could check, BUT, the odds are you have the right bushing and it is indeed a VERY tight fit.
Mechanics trick.........
- Put the new bushing in your freezer overnight and KEEP IT COLD until you're ready to install it.
- Put the part of the control arm that will receive the bushing in some boiling water, or heat it with a torch provided there are no parts that will be damaged.
Working quickly, locate and insert the bushing. A press or large "c" clamp may make the task much easier.
Cheers.

Mar 11, 2016 | 2008 Chevrolet Chevrolet HHR LT

1 Answer

Does my car have rear control arm bushings?


Yes the 95 Camry has rear control arms and you can buy just the bushings

Mar 13, 2014 | 1995 Toyota Camry

1 Answer

Bushings for a 95 chevy


No unless they are worn out, if they are you must do both sides.

Jun 26, 2012 | Chevrolet C1500 Cars & Trucks

1 Answer

I need a diagram of strut rod bushings for a 95 honda accord


sorry dont have a diagram here is a how to

  1. Disconnect the negative battery cable. If equipped with an air bag, properly disable the Supplemental Restraint System (SRS), as detailed in Chassis Electrical .
  2. Elevate and safely support the front of the car.
  3. Remove the wheel.
  4. Loosen the nut at the rear of the radius rod. Remove the nut, washers, bushing, etc. Keep them in the correct order for reinstallation.
  5. Remove the bolts securing the rod to the control arm. Remove the rod.

To install:

  1. Inspect the bushings carefully for wear or deformation. Replace them if any damage is found.
  2. Fit the rod into place and install the bolts at the control arm. Tighten the bolts to 40 ft. lbs. (55 Nm) on Accords through 1989 and Preludes through 1991. On 1990-95 Accords and 1992-95 Preludes, tighten the bolts to 76 ft. lbs. (105 Nm).
  3. Install the bushings, washers and spacers on the rod. Install a new locking nut. On all except 1992-95 Preludes, tighten the end nut to 33 ft. lbs. (44 Nm). On 1992-95 Preludes, tighten the nut to 40 ft. lbs. (55 Nm).
  4. Install the wheels and lower the vehicle.
  5. Properly enable the SRS system, if equipped, and connect the negative battery cable.

Jun 17, 2011 | Honda Accord Cars & Trucks

2 Answers

My front in squeeks an creeks when i hit a low spot or bump. I have had in the shop 3 times> I bought an extended warranty. I am bought ready to give up.


Front end squeaks are usually caused by rubber suspension parts. The most common source are the sway bar bushings. Nest would be the control arm bushings. You can spray the bushings with penetrating oil to see if the squeak stops. This would only be a temporary fix. Do the sway bar bushings first. Spray them down really good, and drive the car for a couple of days. If the squeak goes away, you will know you need to replace the bushings. Do the same thing to the control arm bushings. If you replace any of the bushings, use a high performance neoprene bushing, and use the special lube available before installation. The sway bar bushings will be an easy fix. The control arm bushings will require special equipment, and will need to be done in a shop.

Feb 18, 2011 | 2008 Mercury Milan

2 Answers

I have a 2005 Trailblazer. I have had the stalilizer bar replaced, new ball joints, greesed the fittings on the ball joints. New calipers, rotos and branke pade. HOWEVER, I still have a clunking sound...


They are really bad for the lower control arm bushings causing a clunk noise. You can't see movement by checking on a hoist, but lubing them will help only temporarily. I did a lot of them under warranty, but being 2005 I'm sure yours has expired. I' would highly recommend changing them to eliminate the clunk noise.

Feb 01, 2011 | 2002 Chevrolet TrailBlazer

1 Answer

How do I replace the upper Control arms on My 1979 chevy 1/2 ton pickup. I saw a replacement control arm that has the bushings and ball joints already installed. I'm trying to save the high labor cost that...


Since the new arm comes with the bushings, there is no reason to get the tool to install them. Upper arms are relatively easy to install...just a bolt out, bolt in operation as the springs aren't involved. Support the suspension under the lower control arm to take any tension off the upper arm.

Apr 27, 2010 | 1978 Chevrolet C1500

1 Answer

Removal/replacement of upper control arm bushing


the a arms need to be removed, and the bushings pressed in and out , then you will need to reinstall them and the truck will need a front end alignment. You really need a qualified person to do this.

Sep 16, 2009 | 1985 Chevrolet Chevy

1 Answer

Lower control arm bushing.


i took the car into Winner ford to see if it was the lower control arm bushing again. i also had the oil changed and part of the oil change service includes the lube service, of which the steering stop bushings were lubed. the noise is gone. i have had the lower control arm replaced once (car had only 1500 miles, now 3300) it had sounded like an old man with arthritus!

Jul 02, 2008 | 2008 Ford Mustang

1 Answer

Upper a arm bushings


actually you need to have some experience and some air tools like air hammer and a big bench vise you better take it to a mechanic, or if you want to save some money lift the truck from the lower control arm with a floor jack do not remove jack until you remove and reinstall the upper control arm because the coil or spring fro suspension has lots of pressure and might pop uot and it is very dangerous, then one's you have it out take the bushings and the control arms to a shop and let them do it the go back and reinstall it. that will save you money and headaches

Jun 07, 2008 | 1995 Chevrolet Tahoe

Not finding what you are looking for?
1994 Chevrolet S-10 Blazer Logo

Related Topics:

41 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7772 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...