Question about 2006 GMC Canyon

1 Answer

Coolant leak on drivers side of engine. Radiator is good all hoses are good and just finished replacing intake manifold gasket. Still leaks. I don't know where the freeze plug is located so I can't check that.

Posted by on

  • jbell430 Nov 18, 2009

    No, I replaced that 3 mos. ago. The dripping is near the oil drain plug. The left side of the motor shows coolant.

  • jbell430 Nov 18, 2009

    I'll check around. Thanks

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 4 Answers

Water pump?

Posted on Nov 18, 2009

Testimonial: "This is very late but as it turns out the pump I rented showed the problem to be a pin hole size leak in on of the crevices on the side of the head. Manufacturer defect that they would not remedy. I put JB style weld on it and the leak stopped. Thanx, zschooley "

  • zschooley Nov 18, 2009

    do you know of any one with a radiator pump

    its were you put it on where the cap goes and you will pump it up so much and it puts preasure in there and it makes it leak and you can see were its commin from

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to fix oil leaks in chevy ss impala 1996



Instructions

1. Removal

Unscrew the bolt that holds the negative connection to the Impala's battery. Set this bolt aside for later use.

Remove the engine cover to access the intake manifold and manifold gasket. Disconnect the throttle body inlet duct from the engine.

Twist off the radiator cap to allow draining of the coolant to flow more smoothly. Place an empty container beneath the radiator's drain plug, and remove this plug. Allow all of the engine coolant to drain into the empty container. Replace the drain plug once you are finished.

Tag all of the electrical wiring and hoses before removing so that reconnection is precise to factory settings. Remove these parts, individually, from the intake manifold.

Loosen the bolts that hold the intake manifold to the Impala's engine block. Lift the intake manifold from the block once all bolts have been completely removed.

Use the flat-head screwdriver to pry the old intake manifold gasket from the engine block. Discard this part once you have removed it.

Clean the engine block thoroughly with the engine degreaser and linen cloth. If necessary, use a gasket scraper to remove excess buildup and grime.

2. Installation

  • Coat the top and bottom of the new intake manifold gasket with a chemical sealer so that it bonds to the engine block securely. Position this new manifold gasket so that it lines up perfectly with the cylinder ports of the Impala's engine block.

Place the old intake manifold on top of the newly-installed manifold gasket until it aligns with all of the holes of the cylinder flanges and manifold gasket.

Attach all of the bolts with your hand to the manifold. Once all bolts have been positioned, use a torque wrench and apply 15 foot-pounds of pressure to the bolts to secure the manifold into place.

Reconnect all of the necessary hoses and electrical wiring to the intake. Pour the engine coolant back into the radiator.

Reattach the engine cover on top of the intake manifold and engine block. Start the Impala's engine and check for any leaks around the new intake manifold gasket.

Jul 08, 2012 | 1996 Chevrolet Impala SS

1 Answer

Possibility of a cracked block. how can i be sure/


Vehicles: Any with the above symptoms

A cracked cylinder block will cause either:
(a) motor oil contamination of engine coolant
(b) coolant contamination of motor oil
(c) white exhaust smoke, due to coolant seeping into one or more cylinders.
(d) more than one of the above
(e) all of the above

Oil infiltrating into coolant is easy to see - drain some coolant out through the pepcock at the bottom of the radiator, and place it into a styrofoam coffee cup. Oil droplets floating on top of the green (or orange) coolant are easily seen. Or visualize oil by looking into the top of the radiator through the radiator cap.
Coolant infiltrating into and mixing with motor oil will permanently damage the engine (seizing it up through loss of lubrication), and must be prevented.
A leak from above the front suspension is, as physicians like to put it, "nonspecific", with the most likely cause a water pump seal or hose/hose connection.
A leak from near the fire wall will usually be a heater core hose, or hose connection.
A coolant leak on the same side of the engine as the water pump is a leaking water pump or water pump seal until proven otherwise.

To rule out everythng else, here's the 1999 Honda CR-V Troubleshooting Guide for Coolant Loss/Coolant Leaking:

Priority Action Part Type Cause
1 Inspect Water Pump - Worn, Cracked or Leaking Water Pump, or Water Pump gasket.
2 Inspect Head Gasket - Leaking Head Gasket.
3 Inspect Radiator - Leaking Radiator Hose(s).
4 Inspect Radiator Cap - Worn or Damaged Radiator Cap.
5 Inspect Radiator Hose - Ruptured, Cracked or Leaking Radiator Hose.
6 Inspect Freeze Plug - Leaking Freeze Plug(s).
7 Inspect Intake Manifold Gasket - Leaking, Worn, or Damaged Intake Manifold Gasket.
8 Inspect Water Outlet - Cracked, Leaking or Damaged Water Outlet.
9 Inspect Heater Control Valve - Leaking or Faulty Heater Control Valve.
10 Inspect Radiator Drain Pepcock - Loose, Damaged, or Faulty Radiator Drain Pepcock, or Pepcock O-ring.
11 Inspect Engine (DOMESTIC ONLY) - Cracked Cylinder Block Leaking Coolant into at least one Cylinder, causing white exhaust smoke.

Dec 03, 2011 | 1999 Honda CR-V

1 Answer

I HAVE ANITFREEZE LEAKS FROM MY 2000 CHEVY S10 BLAZER. IT'S HARD TO TELL BUT THE LEAK SEEMS TO BE COMING FROM UNDER THE MOTOR RATHER THAN FROM THE RADIATOR OR ANY HOSE I CAN SEE.


a common V6 failure is the intake manifold gasket. coolant will usually leak behind the water pump on the drivers side, however it can leak at other locations on the intake manifold gasket.

coolant leaks from other areas include the heater core, hoses, expansion plugs, trans cooler, and coolant overflow tank.

Jan 03, 2011 | 2000 Chevrolet Blazer

4 Answers

Loosing coolant no visible leaks about 1/2 gallon every 100 miles


How To Find & Fix Coolant Leaks

861e67b.gif

WHERE COOLANT LEAKS OCCUR
Coolant leaks can occur anywhere in the cooling system. Nine out of ten times, coolant leaks are easy to find because the coolant can be seen dripping, spraying, seeping or bubbling from the leaky component. Open the hood and visually inspect the engine and cooling system for any sign of liquid leaking from the engine, radiator or hoses. The color of the coolant may be green, orange or yellow depending on the type of antifreeze in the system. The most common places where coolant may be leaking are:
Water pump -- A bad shaft seal will allow coolant to dribble out of the vent hole just under the water pump pulley shaft. If the water pump is a two-piece unit with a backing plate, the gasket between the housing and back cover may be leaking. The gasket or o-ring that seals the pump to the engine front cover on cover-mounted water pumps can also leak coolant. Look for stains, discoloration or liquid coolant on the outside of the water pump or engine.

Radiator -- Radiators can develop leaks around upper or loser hose connections as a result of vibration. The seams where the core is mated to the end tanks is another place where leaks frequently develop, especially on aluminum radiators with plastic end tanks. On copper/brass radiators, leaks typically occur where the cooling tubes in the core are connected or soldered to the core headers. The core itself is also vulnerable to stone damage. Internal corrosion caused by old coolant that has never been changed can also eat through the metal in the radiator, causing it to leak.

Most cooling systems today are designed to operate at 8 to 14 psi. If the radiator can't hold pressure, your engine will overheat and lose coolant.

Hoses -- Cracks, pinholes or splits in a radiator hose or heater hose will leak coolant. A hose leak will usually send a stream of hot coolant spraying out of the hose. A corroded hose connection or a loose or damaged hose clamp may also allow coolant to leak from the end of a hose. Sometimes the leak may only occur once the hose gets hot and the pinhole or crack opens up.

Freeze plugs -- These are the casting plugs or expansion plugs in the sides of the engine block and/or cylinder head. The flat steel plugs corroded from the inside out, and may develop leaks that are hard to see because of the plug's location behind the exhaust manifold, engine mount or other engine accessories. On V6 and V8 blocks, the plugs are most easily inspected from underneath the vehicle.

Heater Core -- The heater core is located inside the heating ventilation and air conditioning (HVAC) unit under the dash. It is out of sight so you cannot see a leak directly. But if the heater core is leaking (or a hose connection to the heater core is leaking), coolant will be seeping out of the bottom of the HVAC unit and dripping on the floor inside the passenger compartment. Look for stains or wet spots on the bottom of the plastic HVAC case, or on the passenger side floor.

Intake Manifold gasket -- The gasket that seals the intake manifold to the cylinder heads may leak and allow coolant to enter the intake port, crankcase or dribble down the outside of the engine. Some engines such as General Motors 3.1L and 3.4L V6 engines as well as 4.3L, 5.0L and 5.7L V8s are notorious for leaky intake manifold gaskets. The intake manifold gaskets on these engines are plastic and often fail at 50,000 to 80,000 miles. Other troublesome applications include the intake manifold gaskets on Buick 3800 V6 and Ford 4.0L V6 engines.

INTERNAL COOLANT LEAKS
There are the worst kind of coolant leaks for two reasons. One is that they are impossible to see because they are hidden inside the engine. The other is that internal coolant leaks can be very expensive to repair.

Bad head gasket --Internal coolant leaks are most often due to a bad head gasket. The head gasket may leak coolant into a cylinder, or into the crankcase. Coolant leaks into the crankcase dilute the oil and can damage the bearings in your engine. A head gasket leaking coolant into a cylinder can foul the spark plug, and create a lot of white smoke in the exhaust. Adding sealer to the cooling system may plug the leak if it is not too bad, but eventually the head gasket will have to be replaced.

If you suspect a head gasket leak, have the cooling system pressure tested. If it fails to hold pressure, there is an internal leak. A "block tester" can also be used to diagnose a leaky head gasket. This device draws air from the cooling system into a chamber that contains a special blue colored leak detection liquid. Combustion gases will react with the liquid and cause it to change color from blue to green if the head gasket is leaking.

Head gasket failures are often the result of engine overheating (which may have occurred because of a coolant leak elsewhere in the cooling system, a bad thermostat, or an electric cooling fan not working). When the engine overheats, thermal expansion can crush and damage portions of the head gasket. This damaged areas may then start to leak combustion pressure and/or coolant.

Cracked Head or Block -- Internal coolant leaks can also occur if the cylinder head or engine block has a crack in a cooling jacket. A combustion chamber leak in the cylinder head or block will leak coolant into the cylinder. This dilutes the oil on the cylinder walls and can damage the piston and rings. If the coolant contains silicates (conventional green antifreeze), it can also foul the oxygen sensor and catalytic converter. If enough coolant leaks into the cylinder (as when the engine is sitting overnight), it may even hydro-lock the engine and prevent it from cranking when you try to start it. Internal leaks such as these can be diagnosed by pressure testing the cooling system or using a block checker.

A coolant leak into the crankcase is also bad news because it can damage the bearings. Coolant leaking into the crankcase will make the oil level on the dipstick appear to be higher than normal. The oil may also appear frothy, muddy or discolored because of the coolant contamination.

Leaky ATF oil cooler -- Internal coolant leakage can also occur in the automatic transmission fluid oil cooler inside the radiator. On most vehicles with automatic transmissions, ATF is routed through an oil cooler inside the radiator. If the tubing leaks, coolant can enter the transmission lines, contaminate the fluid and ruin the transmission. Red or brown drops of oil in the coolant would be a symptom of such a leak. Because the oil cooler is inside the radiator, the radiator must be replaced to eliminate the problem. The transmission fluid should also be changed.

continue...

Mar 12, 2010 | 1998 Oldsmobile 88

1 Answer

Loosing antifreeze


f735a20.gif

WHERE COOLANT LEAKS OCCUR
Coolant leaks can occur anywhere in the cooling system. Nine out of ten times, coolant leaks are easy to find because the coolant can be seen dripping, spraying, seeping or bubbling from the leaky component. Open the hood and visually inspect the engine and cooling system for any sign of liquid leaking from the engine, radiator or hoses. The color of the coolant may be green, orange or yellow depending on the type of antifreeze in the system. The most common places where coolant may be leaking are:
Water pump -- A bad shaft seal will allow coolant to dribble out of the vent hole just under the water pump pulley shaft. If the water pump is a two-piece unit with a backing plate, the gasket between the housing and back cover may be leaking. The gasket or o-ring that seals the pump to the engine front cover on cover-mounted water pumps can also leak coolant. Look for stains, discoloration or liquid coolant on the outside of the water pump or engine.

Radiator -- Radiators can develop leaks around upper or loser hose connections as a result of vibration. The seams where the core is mated to the end tanks is another place where leaks frequently develop, especially on aluminum radiators with plastic end tanks. On copper/brass radiators, leaks typically occur where the cooling tubes in the core are connected or soldered to the core headers. The core itself is also vulnerable to stone damage. Internal corrosion caused by old coolant that has never been changed can also eat through the metal in the radiator, causing it to leak.

Most cooling systems today are designed to operate at 8 to 14 psi. If the radiator can't hold pressure, your engine will overheat and lose coolant.

Hoses -- Cracks, pinholes or splits in a radiator hose or heater hose will leak coolant. A hose leak will usually send a stream of hot coolant spraying out of the hose. A corroded hose connection or a loose or damaged hose clamp may also allow coolant to leak from the end of a hose. Sometimes the leak may only occur once the hose gets hot and the pinhole or crack opens up.

Freeze plugs -- These are the casting plugs or expansion plugs in the sides of the engine block and/or cylinder head. The flat steel plugs corroded from the inside out, and may develop leaks that are hard to see because of the plug's location behind the exhaust manifold, engine mount or other engine accessories. On V6 and V8 blocks, the plugs are most easily inspected from underneath the vehicle.

Heater Core -- The heater core is located inside the heating ventilation and air conditioning (HVAC) unit under the dash. It is out of sight so you cannot see a leak directly. But if the heater core is leaking (or a hose connection to the heater core is leaking), coolant will be seeping out of the bottom of the HVAC unit and dripping on the floor inside the passenger compartment. Look for stains or wet spots on the bottom of the plastic HVAC case, or on the passenger side floor.

Intake Manifold gasket -- The gasket that seals the intake manifold to the cylinder heads may leak and allow coolant to enter the intake port, crankcase or dribble down the outside of the engine. Some engines such as General Motors 3.1L and 3.4L V6 engines as well as 4.3L, 5.0L and 5.7L V8s are notorious for leaky intake manifold gaskets. The intake manifold gaskets on these engines are plastic and often fail at 50,000 to 80,000 miles. Other troublesome applications include the intake manifold gaskets on Buick 3800 V6 and Ford 4.0L V6 engines.

INTERNAL COOLANT LEAKS
There are the worst kind of coolant leaks for two reasons. One is that they are impossible to see because they are hidden inside the engine. The other is that internal coolant leaks can be very expensive to repair.

Bad head gasket --Internal coolant leaks are most often due to a bad head gasket. The head gasket may leak coolant into a cylinder, or into the crankcase. Coolant leaks into the crankcase dilute the oil and can damage the bearings in your engine. A head gasket leaking coolant into a cylinder can foul the spark plug, and create a lot of white smoke in the exhaust. Adding sealer to the cooling system may plug the leak if it is not too bad, but eventually the head gasket will have to be replaced.

If you suspect a head gasket leak, have the cooling system pressure tested. If it fails to hold pressure, there is an internal leak. A "block tester" can also be used to diagnose a leaky head gasket. This device draws air from the cooling system into a chamber that contains a special blue colored leak detection liquid. Combustion gases will react with the liquid and cause it to change color from blue to green if the head gasket is leaking.

Head gasket failures are often the result of engine overheating (which may have occurred because of a coolant leak elsewhere in the cooling system, a bad thermostat, or an electric cooling fan not working). When the engine overheats, thermal expansion can crush and damage portions of the head gasket. This damaged areas may then start to leak combustion pressure and/or coolant.

Cracked Head or Block -- Internal coolant leaks can also occur if the cylinder head or engine block has a crack in a cooling jacket. A combustion chamber leak in the cylinder head or block will leak coolant into the cylinder. This dilutes the oil on the cylinder walls and can damage the piston and rings. If the coolant contains silicates (conventional green antifreeze), it can also foul the oxygen sensor and catalytic converter. If enough coolant leaks into the cylinder (as when the engine is sitting overnight), it may even hydro-lock the engine and prevent it from cranking when you try to start it. Internal leaks such as these can be diagnosed by pressure testing the cooling system or using a block checker.

A coolant leak into the crankcase is also bad news because it can damage the bearings. Coolant leaking into the crankcase will make the oil level on the dipstick appear to be higher than normal. The oil may also appear frothy, muddy or discolored because of the coolant contamination.

Leaky ATF oil cooler -- Internal coolant leakage can also occur in the automatic transmission fluid oil cooler inside the radiator. On most vehicles with automatic transmissions, ATF is routed through an oil cooler inside the radiator. If the tubing leaks, coolant can enter the transmission lines, contaminate the fluid and ruin the transmission. Red or brown drops of oil in the coolant would be a symptom of such a leak. Because the oil cooler is inside the radiator, the radiator must be replaced to eliminate the problem. The transmission fluid should also be changed.

continue..

Mar 12, 2010 | 2007 Hummer H3X

1 Answer

Hello, i have a coolant leak i thought it was the water pump but the leak is above the mount bolt of the water pump beside the valve cover no coolant has gone in the valve interior, could it be a cracked...


A crack in that area of the block, while possible, is highly unlikely. A crack in the block usually happens in between the cylinder walls on the side of the block. It is most likely leaking from the intake manifold gasket that connects the intake manifold to the heads, or if the upper radiator hose connects to the intake manifold, it could be leaking from the thermostat housing or hose. There are also coolant temperature sensors that are mounted in that area. Or last but not least, it could be leaking from one of the freeze plugs in the end of the head. Coolant runs through the block, heads and intake manifold.

Jan 03, 2010 | Chevrolet 1500 Cars & Trucks

1 Answer

Radiator leak 99 Ford Expedition back drivers side


You are likely leaking coolant from a heater line or hose,check the hose that comes from the water pump{smaller of the two] and see if it has a leak in it or if there is just a loose hose clamp.If you can't find a leak in the hoses or any steel tubes then you need to take it to a radiater shop and have it pressure tested to see if you have a leak in the intake manifold gasket or maybe even the head gasket,good luck.

Dec 02, 2009 | 2001 Ford Expedition

3 Answers

1999 Pontiac Grand Am with "lower intake leak"...What does this mean specifically? Would this mean the intake for the radiator, gasket, or valve?


Usually intake has to do with the induction system, as in intake manifold , The intake manifold can have several types of leaks, the intake can have a vacuum leak, oil leak, coolant leak or a combination of any of the before mentioned....hope this helps,

Aug 30, 2009 | 1999 Pontiac Grand Am GT

2 Answers

My daughter's 1997 Saturn is leaking coolant and overheating..


Coolant leaks can occur anywhere in the cooling system. Nine out of ten times, coolant leaks are easy to find because the coolant can be seen dripping, spraying, seeping or bubbling from the leaky component. So open the hood and visually inspect the engine and cooling system for any sign of liquid leaking from the engine, radiator or hoses. The color of the coolant may be green, orange or yellow depending on the type of antifreeze in the system. The most common places where coolant may be leaking are:Water pump. A bead shaft seal will allow coolant to dribble out of the vent hole just under the water pump pulley shaft. If the water pump is a two-piece unit with a backing plate, the gasket between the housing and back cover may be leaking. The gasket or o-ring that seals the pump to the engine front cover on cover-mounted water pumps can also leak coolant. Look for stains, discoloration or liquid coolant on the outside of the water pump or engine.Radiator. Radiators can develop leaks around upper or loser hose connections as a result of vibration. The seams where the core is mated to the end tanks is another place where leaks frequently develop, as is the area where the cooling tubes in the core are connected or soldered to the core headers. The core itself is also vulnerable to stone damage. But a major factor in many radiator leaks is internal corrosion that eats away from the inside out. That's why regular coolant flushes and replacing the antifreeze is so important.
oses. Cracks, pinholes or splits in a radiator hose or heater hose will leak coolant. A hose leak will usually send a stream of hot coolant spraying out of the hose. A corroded hose connection or a loose or damaged hose clamp may also allow coolant to leak from the end of a hose. Sometimes the leak may only occur once the hose gets hot and the pinhole or crack opens up. Freeze plugs (casting plugs or expansion plugs in the sides of the engine block and/or cylinder head). The flat steel plugs corroded from the inside out, and eventually eat through allowing coolant to leak from the engine. The plugs may be hard to see because they are behind the exhaust manifold, engine mount or other engine accessories. On V6 and V8 blocks, the plugs are most easily inspected from underneath the vehicle.
Heater Core. The heater core is located inside the heating ventilation and air conditioning (HVAC) unit under the dash. It is out of sight so you can�t see a leak directly. But if the heater core is leaking (or a hose connection to the heater core is leaking), coolant will be seeping out of the bottom of the HVAC unit and dripping on the carpet. Look for stains or wet spots on the bottom of the plastic HVAC case, or on the passenger side floor.
Intake Manifold gasket. The gasket that seals the intake manifold to the cylinder heads may leak and allow coolant to enter the intake port, crankcase or dribble down the outside of the engine. Some engines such as General Motors 3.1L and 3.4L V6 engines as well as 4.3L, 5.0L and 5.7L V8s are notorious for leaky intake manifold gaskets. The intake manifold gaskets on these engines are plastic and often fail at 30,000 to 80,000 miles. Other troublesome applications include the intake manifold gaskets on Buick 3800 V6 and Ford 4.0L V6 engines.
INTERNAL COOLANT LEAKS
There are the worst kind of coolant leaks for two reasons. One is that they are impossible to see because they are hidden inside the engine. The other is that internal coolant leaks can be very expensive to repair.


visit for more info:

http://www.aa1car.com/library/coolant_leaks.htm

Nov 24, 2008 | 1996 Saturn SL

Not finding what you are looking for?
2006 GMC Canyon Logo

310 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...