Question about Chevrolet Chevy

Open Question

How do i change rear brake pads on a chevrolet lacetti

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: 2001 Chevrolet Silverado

How do I remove the old front brake pads from a 2001 silverado?

Posted on Oct 24, 2008

Ad
samson-1
  • 153 Answers

SOURCE: rear brake cylinders are stuck, can not push them in

I'm not sure about your vehicle but some models must be turned as they go back.

Posted on Oct 27, 2008

  • 651 Answers

SOURCE: CHANGING REAR BRAKE PADS

the best thing you can do is go to an autoparts store and purchase a haynes repair manual for your car. cost about $18, but will show you everything you need to know, with pictures.

Posted on Nov 28, 2008

greg_margo
  • 1959 Answers

SOURCE: Jeep Commander Rear Brake Pad Installation

Per Chilton Auto repair manual:

Removal & Installation

  1. Raise and safely support the vehicle.
  2. Remove the rear wheel.
  3. Siphon a small amount of brake fluid from the master cylinder reservoir.
  4. Insert a small prybar through the caliper opening and pry the caliper cover (using the outboard brake pad) to bottom the piston in the caliper bore.
  5. Remove the caliper slide bolts.
  6. Remove the caliper from the anchor.

    WARNING Support the brake caliper with mechanics wire. Do not let the caliper hang by the brake hose.
  7. Remove the brake pads from the caliper.
To install:
  1. Install the brake pads onto the caliper.
  2. Lubricate the slide pin bolts with grease provided with the brake pads, or suitable silicon grease equivalent.
  3. Install the caliper on the anchor and tighten the slide pin bolts to 18 ft. lbs. (25 Nm).
  4. Install the rear wheel.
  5. Lower the vehicle.
  6. Pump the brake pedal several times until a firm pedal is obtained in order to properly seat the pads.
  7. Refill the brake fluid reservoir to the proper level.

Posted on May 17, 2009

Louie_3006
  • 79 Answers

SOURCE: how to change rear brake shoe pads of 2005 mitsubishi lancer

Hello, this do it yourself project is very manageable if it is brake pads that you are replacing on your car; if they are disc shoes it may be a little bit harder. In essence a brake job can be done straight out of a auto manual for your car and is not to diffucult as long as you follow good safety procedures while jacking up your vehicle and removing your wheels. First, I would park your car and setting your parking break will make your rear brakes impossible to get off so do not set it. I would however keep this in mind and be very careful working on your car then. I would chaulk your front wheel with a chaulk block or a brick. I would loosen your lug nuts just to break the intial torque I would then jack up the rear of your vehicle and set jack stands under your car in the proper locations. Then systematically, remover your wheel and then the two bolts holding your caliper to the spindle. Carefully, remove the caliper and do not let it hang becuase you will bend your brake line. Remove old shoes, then compress the caliper with a caliper compression tool from your local auto parts store or a c-clamp and a small block of wood. Inspect the rotor for deep gouges, a blue tint, or if you know you have gotten them really hot before I would replace the rotor. Next, install the new brake pads, put rotor back onto spindle and insert bolts back into caliper housing. Repeat for the next side and put the wheel back on and remember to torque your lug nuts to the proper specification. I hope this fixes your problem for you!

Posted on May 25, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Wat fuse is it and where on the car is it for brake lights on a Chevrolet Lacetti


I have no idea what a Lacetti is, but if you suspect a fuse problem, why not just check them all?

Mar 10, 2016 | Chevrolet Cars & Trucks

1 Answer

2000 Silverado changed front and rear brake pads now rear calipers are overheating. All disc no drum. Thanx


rear pads dont have so much work to do as front are the sliders free might be sticking on a bit so binding.or badly adjusted parking brake so not fully disengaged?

May 28, 2015 | 2000 Chevrolet Silverado

1 Answer

What other cars have the same crank shaft sensor as a chevrolet lacetti 2006, chevrolet opera 2006


check with GM spares as the sensor is probably the same used in a wide variety of Chevs of the same engine family.

Dec 03, 2014 | Chevrolet Cars & Trucks

1 Answer

My buddy changed the rear brake pads on my chevy silverado 99 / 1500 and when i drive off the brakes heat up


The rear brakes are adjusted to tight or the parking bbrake portion of the brakes was not installed properly or the parking brake is on.

Apr 29, 2011 | 1999 Chevrolet Silverado 1500

1 Answer

I have oil leaking from the rear driver side tire after changing the front brake pads, (did not bleed the brakes)


you have a rear wheel cylinder leaking and its puerly coincidental that you saw it at the same time as changing the front brake pads

Jan 23, 2011 | 2004 Chevrolet Cavalier

1 Answer

Abs/AWD light on 04 venture


Have you checked the brake fluid level?

Jun 06, 2010 | 2004 Chevrolet Venture Passanger

1 Answer

Changed the rear brake pads and now the brakes wont release.


When you replaced the pads did you make sure the calipers were working properly?, did you bleed the brake lines?, is emergency brake cable completely releaseing the rear brakes or is it hung up somewere?. Check these things first and if all is OK get it to mechanic.

Dec 22, 2009 | 2002 Chevrolet Blazer

3 Answers

Rear brake dragging


Suterman, RE: infamous GM right rear brake pad problem. A rapid inside RR brake pad wear problem is common on most GMC and Chevy trucks made from ?99 to ?04. The right rear brake caliper and pads are located in such a manner that road dirt/mud flies straight into them. This steady diet of grit causes the caliper to seize and the inside brake pad to wear out rapidly, causing the "squealing" or "grinding" noise often reported. SOLUTION: GM has had a problem with the rear brakes on their light duty trucks. There is a fix. The ALLDATA Information System shows GM Technical Service Bulletin # 00-05-23-005B, which they simply describe is a mud flap kit. This kit addresses the rapid brake pad wear problem. The GM mud flap kit is installed to block bombardment of road dirt and debris that is the cause of this very common problem. The GM kit part number is 15765007 and is pretty easy to install. I would suggest installing the mud flap kit before your next brake job.

Mar 04, 2009 | 2001 Chevrolet Silverado 1500

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

447 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8514 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...