Question about 1997 Hyundai Elantra

1 Answer

I need the cylinder head torque settings for 1997

I need the cylinder head (and associated parts) torque settings for 1997 1.8L hyundai lantra

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 280 Answers

1998 Hyundai Lantra "G4GM" engine 1795cc.there are two heads or blocks, one is called the M10, other is the M12, figure out which one you have cause the torque is different for stage one by 5nm........... Dont get confused theres 2 different engines so 2 different torques for stage1---------
heres the full details: Stage 1 - m10 = 30nm / m12 = 35nm-------------------------- -------- Stage 2 - tighten by 60-65 degrees ------------ stage 3 - tighten by 60-65 degrees. no sequence is given in the data book for tightening so go off what you thinks right, it doesn't matter on this engine.

Posted on Jan 26, 2010

Testimonial: "Very accurate answer. Thanks, all is well now"

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I need the cylinder head torque settings for a hyundai getz 1.6 16 valve double overhead cam Engine cod G4ED


renew bolts
stage1- 30NM
stage2-90deg
stage3-individually slacken off 360deg
stage4-30NM
stage5-90deg

crank pulley bolt-142NM
cam sprocket bolt-88NM

i like to help people like you that give engine codes it makes it so much easier

Jul 20, 2016 | Hyundai Cars & Trucks

1 Answer

Torque settings head bolt hyundai 2.2 crdi 2006


is your motors head torques listed on

also has torque sequence page number reference layouts are bottom of the document

page 33 as a pdf

or page 50 of paper listings

http://olybrake.com/pdf/fel_pro_torque_specs_guide.pdf

May 11, 2016 | Hyundai Santa Fe Cars & Trucks

1 Answer

Could you advise what are the cylinder head bolt tension settings for hyundai lantra j5. Could you email me back on judy.ben@optusnet.com.au. Thanks


let me see if i can get some info 4 you.

edit
REMOVAL

1. Drain the coolant and disconnect the upper radiator hose.
2. Remove the breather hose (between the air cleaner and the head cover).
3. Remove the air-intake hose.
4. Remove the vacuum hose, fuel hose and coolant hose.
5. Remove the cables from the spark plugs. The cables should be removed by holding the boot portion.
6. Remove the ignition coil.
7. Remove the power steering oil pump and bracket.
8. Remove the intake manifold.
9. Remove the heat protector and exhaust manifold assembly.
10. Remove the coolant pump pulley and the crankshaft pulley.
11. Remove the timing belt cover.
12. Remove the timing belt tensioner pulley.
13. Remove the timing belt.
14. Remove the head cover.


15. Remove the cylinder head assembly. The cylinder head bolts should be removed by using Special Tool, Cylinder Head Bolt Wrench (09221-32001) or equivalent, in the sequence as shown in the illustration in two or three steps.
16. Remove the gasket pieces from the cylinder block top surface and cylinder head bottom surface. NOTE: Make sure that the gasket pieces do not fall in the engine.

INSTALLATION

1. Clean all gasket surfaces of the cylinder block and the cylinder head.
2. Install a new cylinder head gasket onto the cylinder head assembly. Apply sealant to the gasket and do not reuse the old cylinder head gasket.


3. Install the cylinder head bolts. Starting at top center, tighten all cylinder head bolts in sequence as shown in illustration, using the Cylinder Head Bolt Wrench (09221 - 32001) or equivalent. Repeat the procedure, re-tightening all cylinder head bolt to the specified torque. (torque spec is Cold Engine 105-115 Nm (76-83 ft lb) )
4. Install the timing belt tensioner pulley.
5. Install the timing belt on the camshaft sprocket, making sure that the tension side is tightened by turning the camshaft sprocket in reverse, all timing marks are in alignment.
6. Adjust the timing according to "Timing Belt"
7. Install the rocker cover and tighten the bolts to the specified torque. Tightening torque: Rocker cover belt:

2.5-3.5 Nm (25-35 kg.cm, 2-3 ft. lbs.)

8. Install the timing belt cover.
9. Install the new intake manifold gasket and the intake manifold. Tighten the nuts and bolts to the specified torque.
10. Install the new exhaust manifold gasket and the exhaust manifold. Tighten the exhaust manifold attaching nuts to the specified torque.
11. Install the surge tank and tighten the nuts bolts to the specified torque.
12. Install the power steering oil pump and bracket.
13. Install the ignition coil.
14. Install the air intake hose.
15. Connect the vacuum hose, fuel hose and water hose.
16. Install breather hose.

Jun 08, 2011 | Hyundai Elantra Cars & Trucks

1 Answer

1996 hyundai lantra cylinder head torque spec


dak408_40.gif
Revised Bulletin
This TSB supersedes the Cylinder Head Bolt Torque Specifications previously described in TSB # 96-20-003, TSB # 96-20-003-1 and TSB # 97-20-004.
DESCRIPTION:
This bulletin provides torque specification corrections to the 1996 and 1997 Elantra Shop Manual, 1997 Elantra Service Data Book, 1997 Tiburon Shop Manual and 1997 Tiburon Service Data Book.
Please record the corrections (listed) in the appropriate manuals and write the TSB number on the bottom of the pages listed below for future reference.
CYLINDER HEAD BOLT:
(M10) 30 Nm (300 kg.cm; 22 lb.ft) + (60°to 65°) + (60°to 65°)
(M12) 35 Nm (350 kg.cm; 26 lb.ft) + (60°to 65°) + (60°to 65°)

Nov 21, 2010 | Hyundai Motor 1996 Elantra

1 Answer

Correct torque on cylinder head bolts for Hyundai Elantra 1.8GLS


You have two bolt sizes the shorter or smaller of the two sizes is called M10 the torque is 22ft lbs +65 degrees +65 degrees again The larger of the two bolts is called a M12 the torque for these are 26ft lbs +65+65. There is a tightening order staring at the top center bolt and working in a circle They have to be torqued in three steps. If you dont under stand something about this repost and I can help you farther. If this is helpful please mark that it was I do this for free to help people DRIVE SAFE TIM

Feb 19, 2010 | 1997 Hyundai Elantra

2 Answers

Torque wrench settings for 97 hyundai lantra 1.8


They use throw away bolts. One use only, so don't reuse your old ones. You will need new ones. The smaller bolts 1st torque setting 22Ft/Lbs and the larger 26ft/lbs, the 2nd torque setting 60 degrees both bolt sizes and the 60 degrees for the third.

May 20, 2009 | 1997 Hyundai Elantra

1 Answer

How do i fit rings to my hyundai lantra 1.8, also wrench setting for engine.


You have to use a ring compressor. Available at any auto parts store.

May 16, 2009 | 1997 Hyundai Elantra

1 Answer

Hyundai Lantra 1996 1.8l


M10 30 Nm (22 ft lb) + (60°+65°) + (60°+65°) M12 35 Nm (26 ft lb) + (60°+65°) + (60°+65°)

Jun 01, 2008 | Hyundai Motor 1996 Elantra

Not finding what you are looking for?
1997 Hyundai Elantra Logo

627 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

77499 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8825 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...