Question about 1994 Ford Thunderbird

1 Answer

High shifting rpms in first gear will go to almost 3000 rpms before shift

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 117 Answers

The governor is stuck or the detent cable is broken.

Posted on Dec 19, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hyundai tiburon running at high rpms when shifting


hmmm....it would seem as if your trans is having a bit of a hard time shifting so its sort of waiting before it can shift to the next gear (possible the gear system is having a problem shifting due to it sticking to some gears) i'd have to say....a mechanic can take a look to see why its seemingly shifting late at high RPMs to me IMO the trans is just having a hard time shifting with gears wanting to stick together making the whole trans have a hard time shifting

Jan 05, 2017 | Hyundai Cars & Trucks

1 Answer

Why wont my nissan altima shift into overdrive


run the fault codes as there may be a problem i he VSS or TCM module

Jul 18, 2017 | 2005 Nissan Altima

1 Answer

High rpms when shifting into gear


check the linkage adjustment and also a bad motor mount

Jul 05, 2012 | 1993 GMC Sierra C3500

1 Answer

My turbo 400 shifts very hard and at a high rate of rpms 2600-3000 rpms and sometimes if i shift with shifter it will shift and sometimes not ?


You need a new transmission modulator valve it controls the shift points of the transmission with vacuum.

Dec 10, 2011 | Chevrolet Cars & Trucks

1 Answer

When pulling away the rpms run up to 3000 before shifting up


dude i have the same exact issue . have you learned anything new since the post ? i changed the maf sensor and it did nothing

Jun 23, 2010 | 1999 Mercury Cougar

1 Answer

92 prelude si (auto)


With normal acceleration the 1st to second shift point should be around 2500-3000 rpm. Most of your shifts under moderate acceleration will take place at this same point or when there a light load on the transmission. Under hard acceleration the RPMs will climp higher due to increased power needs and the computer will shift when less power is needed or the RPMs climb to an unsafe speed say5000-6000rpms (depending on where yours redlines). Also going up a steep hill will raise the RPMs higher and goind down a hill will cause a faster shift at lower RPMs. These can always be altered by an individual owner by adjusting shift points, using performance parts and if you have problems (low tranny fluid/trans issues). Your trans RPMS are fine and will vary depening on how your foot accelerates. The shift pattern should be the same every time you drive slow/medium/fast/, look for changes in those patterns you will also catch a problem early.

Jun 14, 2009 | 1992 Honda Prelude

2 Answers

Transmition wont shift


Sounds like a bad toque convertor or a bad front pump

May 23, 2009 | 1998 Ford Explorer

1 Answer

1995 grand cherokee trans not shifting in to second gear


Check transmission fluid levels,,replace lost fluid as needed,,,if this does not work,,take the car to a mechanic,,,sorry to say,,this kind of problem almost alway's requires a transmission mechanic to repair.

Jan 13, 2009 | 1995 Jeep Grand Cherokee

2 Answers

2004 jeep wrangler 2.4 litre 4 cylinder


check the ground wirea at the dipstick tube,remove them all,and bend the ends of the wire,look for weak or broken wires, i bought several 4 cyl jeep that had problems at shift, fall on their face < after the engine settled back in to place,so wires made contact> just a thot. the ground wires are small the engine moves,when shifting.

Jul 29, 2008 | 2004 Jeep Wrangler

Not finding what you are looking for?
1994 Ford Thunderbird Logo

Related Topics:

71 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5471 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...